Rework of off-specification product
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 2 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 46 % der Verlustzeit der Linie. Berichtet von 5 der 127 Studien, die sie beobachten konnten (gute Evidenz).
Was passiert
Product or packages produced during stable running fail to meet weight, fill, seal, appearance or other quality specifications at first pass and must be diverted for reprocessing, re-filling, re-labeling or re-packing instead of being accepted as good output. The underlying root causes can be process drift, material variability or minor equipment misadjustment, but the loss itself is the material, time and capacity consumed in recovering the units rather than scrapping them.
Was man dagegen tut
Tighten process control (fill weight, seal temperature/pressure, closure torque) through SPC and automatic feedback loops to reduce the generation of off-spec units at the source, and standardize rework procedures with clear acceptance criteria to minimize the handling time per diverted unit. Root-cause the recurring defect types feeding rework and address them through equipment calibration, material qualification or operator training rather than relying on downstream recovery.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 1,5 % [0,5–3,4 %]
- Erwarteter Anteil an der Verlustzeit
- 0,7 % [0,2–1,6 %]
- Anteil an der Verlustzeit bei Auftreten
- 46 % [35–57 %]
- Studien / Einheiten
- 127 / 161
- Evidenzgrad
- B
Grad B: 5 bis 9 Studien oder eine Intervallbreite zwischen 0,20 und 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte1,6 % [0,3–4,9 %]13 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte1,8 % [0,4–5,0 %]26 Studien
- Bier, Wein und Spirituosen4,3 % [0,8–12,7 %]11 Studien
- Backwaren und Teigwaren1,4 % [0,2–3,8 %]24 Studien
- Fleisch, Geflügel und Fisch1,6 % [0,2–5,2 %]9 Studien
- Obst- und Gemüseverarbeitung1,7 % [0,2–5,4 %]7 Studien
- Getreide- und Ölsaatenmüllerei1,7 % [0,3–5,3 %]6 Studien
- Zucker und Süßwaren2,2 % [0,4–6,8 %]9 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel1,7 % [0,2–5,5 %]5 Studien
- Futtermittel und Heimtiernahrung1,6 % [0,3–5,0 %]7 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)1,6 % [0,2–5,2 %]10 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseProduct or packages produced during stable running fail to meet weight, fill, seal, appearance or other quality specifications at first pass and must be diverted for reprocessing, re-filling, re-labeling or re-packing instead of being accepted as good output. The underlying root causes can be process drift, material variability or minor equipment misadjustment, but the loss itself is the material, time and capacity consumed in recovering the units rather than scrapping them.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseMES/quality modules show elevated counts of units flagged as rework or rejected-but-recoverable, often tied to a diversion or reject-lane actuator cycling, with a parallel rework or reprocessing line showing increased throughput and run time. Checkweigher, vision or seal-tester reject counters rise while overall line OEE availability stays largely unaffected, concentrating the loss in the quality/yield metric rather than in downtime.
Gegenmaßnahme
Ingenieurpraktische HinweiseTighten process control (fill weight, seal temperature/pressure, closure torque) through SPC and automatic feedback loops to reduce the generation of off-spec units at the source, and standardize rework procedures with clear acceptance criteria to minimize the handling time per diverted unit. Root-cause the recurring defect types feeding rework and address them through equipment calibration, material qualification or operator training rather than relying on downstream recovery.
4Quellen
- Analisis Efektivitas Mesin pada Divisi Pengalengan Jamur Di PT XYZ Menggunakan Metode Overall Equipment Effectiveness (2019)Quelle öffnenAnteil an der geplanten Zeit: 0 % · laut Bericht: “Rework Losses”
Wörtliches Zitat anzeigen
Rata-Rata 0,099271 9,29814 30,74813 0,00000 0,00000 0,13414
- Optimizing beverage manufacturing: integrating lean manufacturing and machine learning to enhance efficiency and reduce waste (2025)Quelle öffnenAnzahl der Ereignisse: 4,00 Boxes x 12 · laut Bericht: “Rework”
Wörtliches Zitat anzeigen
Rework Average 7 4
- Optimizing beverage manufacturing: integrating lean manufacturing and machine learning to enhance efficiency and reduce waste (2025)Quelle öffnenAnzahl der Ereignisse: 7,00 Boxes x 12 · laut Bericht: “Rework”
Wörtliches Zitat anzeigen
Rework Average 7 4
- Enhancing operational efficiency in craft beer production: implementation of lean manufacturing and TPM methodologies in SMES (2025)Quelle öffnenAnteil an der Verlustzeit: 14,0 % · laut Bericht: “reprocessing”
Wörtliches Zitat anzeigen
Among the main causes identified, errors in the conduct of operations accounted for 39.20%, reprocessing constituted 13.95%, and process shutdowns due to machine failures covered 46.85%.
- Analisis Efektivitas Mesin pada Divisi Pengalengan Jamur Di PT. Suryajaya Abadiperkasa Menggunakan Metode Overall Equipment Effectiveness (2020)Quelle öffnenAnteil an der Verlustzeit: 0 % · laut Bericht: “Rework Losses”
Wörtliches Zitat anzeigen
Rata-Rata 0,099271 9,29814 30,74813 0,00000 0,00000 0,13414
- Enhancing Operational Efficiency in Craft Beer Production: Implementation of Lean Manufacturing and TPM Methodologies in SMEs (2024)Quelle öffnenAnteil an der Verlustzeit: 14,0 % · laut Bericht: “reprocessing”
Wörtliches Zitat anzeigen
errors in the conduct of operations accounted for 39.20%, reprocessing constituted 13.95%, and process shutdowns due to machine failures covered 46.85%.
- Optimizing Beverage Manufacturing: Integrating Lean Manufacturing and Machine Learning to Enhance Efficiency and Reduce Waste (2024)Quelle öffnenFehlerquote: 12,0 % · laut Bericht: “reprocessing”
Wörtliches Zitat anzeigen
The main issues concerning the product process include 25% of incorrectly labeled bottles, 18% of improperly sealed bottles, and 12% of reprocessing in the current alcoholic beverage production process.
- Aggregate Analysis of Packaging Machine Effectiveness Using the OEE Method at PT. XYZ (2025)Quelle öffnenAnteil an der Verlustzeit: 22,0 % · laut Bericht: “Rework Losses”
Wörtliches Zitat anzeigen
Rework Losses 8.890 29.095 22% 72%
- Aggregate Analysis of Packaging Machine Effectiveness Using the OEE Method at PT. XYZ (2025)Quelle öffnenVerlustzeit: 8.890 Minutes · laut Bericht: “Rework Losses”
Wörtliches Zitat anzeigen
Rework Losses 8.890 29.095 22% 72%
- Enhancing Operational Effectiveness in a Beverage Bottling SME through SMED, 5S, and TPM Maintenance Practices (2025)Quelle öffnenAnteil an der Verlustzeit: 19,0 % · laut Bericht: “the necessity for product reprocessing”
Wörtliches Zitat anzeigen
Detailed decomposition of the shortfall reveals that parasitic machine velocity losses exert a 47% share on ineffective output, protracted repair durations 34%, and the necessity for product reprocessing 19%.
- Machine Learning, MRP, and Lean Tools as an Internal Innovation Strategy to Improve Efficiency in a Bottling Company (2025)Quelle öffnenFehlerquote: 19,0 % · laut Bericht: “rework”
Wörtliches Zitat anzeigen
In the initial process diagnosis, an inefficiency level of 19% was identified, reflecting high variability, rework, and bottlenecks.
- Machine Learning, MRP, and Lean Tools as an Internal Innovation Strategy to Improve Efficiency in a Bottling Company (2025)Quelle öffnenFehlerquote: 13,0 % · laut Bericht: “rework”
Wörtliches Zitat anzeigen
With the validation of the pilot test, this value was reduced to 13%, representing a relative improvement of 32% compared to the initial condition.
- Improving Production Efficiency in a Chocolate SME through Continuous Flow, SMED and Poka-Yoke (2026)Quelle öffnenFehlerquote: 25,0 % · laut Bericht: “reprocessing”
Wörtliches Zitat anzeigen
Reprocessing: 25% → 5%
- Improving Production Efficiency in a Chocolate SME through Continuous Flow, SMED and Poka-Yoke (2026)Quelle öffnenFehlerquote: 5,00 % · laut Bericht: “reprocessing”
Wörtliches Zitat anzeigen
Reprocessing: 25% → 5%
- Penerapan Konsep Total Productive Maintenance (TPM) dalam Peningkatan Overall Equipment Effectiveness (OEE) pada Mesin Pengisian Botol di PT Trita Musi Prasada (2026)Quelle öffnenVerlustzeit: 0 menit · laut Bericht: “Rework Loss”
Wörtliches Zitat anzeigen
Rework Loss 0 0% 100%
- Penerapan Konsep Total Productive Maintenance (TPM) dalam Peningkatan Overall Equipment Effectiveness (OEE) pada Mesin Pengisian Botol di PT Trita Musi Prasada (2026)Quelle öffnenVerlustzeit: 0 menit · laut Bericht: “Rework Loss”
Wörtliches Zitat anzeigen
Rework Loss 0 0% 100%

