Automation and instrumentation failure
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 56 % der Verlustzeit der Linie. Berichtet von 2 der 127 Studien, die sie beobachten konnten (begrenzte Evidenz).
Was passiert
A fault develops in the control or instrumentation layer of the line, such as a PLC or drive malfunction, a failed sensor or transmitter, a damaged cable or connector, or corrupted control logic. Because equipment control, interlocks or measurement depend on these elements, the affected machine or section loses proper function and cannot continue running safely or correctly until the fault is diagnosed and repaired.
Was man dagegen tut
Apply preventive calibration, testing and cleaning of sensors, transmitters and control cabinets on a scheduled basis, keep spare I/O cards, drives and critical instruments on hand, and use condition monitoring or diagnostic alarms on control networks to detect degradation before a hard failure occurs. Where the loop is critical to production continuity, add redundancy or voting logic to tolerate a single instrument or module failure.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,8 % [0,2–2,0 %]
- Erwarteter Anteil an der Verlustzeit
- 0,4 % [0,1–1,1 %]
- Anteil an der Verlustzeit bei Auftreten
- 56 % [45–66 %]
- Studien / Einheiten
- 127 / 161
- Evidenzgrad
- C
Grad C: 2 bis 4 Studien oder eine Intervallbreite über 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,9 % [0,1–3,0 %]13 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,8 % [0,1–2,4 %]26 Studien
- Bier, Wein und Spirituosen0,9 % [0,1–3,0 %]11 Studien
- Backwaren und Teigwaren1,1 % [0,2–3,5 %]24 Studien
- Fleisch, Geflügel und Fisch0,9 % [0,1–3,1 %]9 Studien
- Obst- und Gemüseverarbeitung0,9 % [0,1–3,0 %]7 Studien
- Getreide- und Ölsaatenmüllerei0,9 % [0,1–3,2 %]6 Studien
- Zucker und Süßwaren1,3 % [0,2–4,3 %]9 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,9 % [0,1–3,0 %]5 Studien
- Futtermittel und Heimtiernahrung0,9 % [0,1–3,2 %]7 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,9 % [0,1–3,0 %]10 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseA fault develops in the control or instrumentation layer of the line, such as a PLC or drive malfunction, a failed sensor or transmitter, a damaged cable or connector, or corrupted control logic. Because equipment control, interlocks or measurement depend on these elements, the affected machine or section loses proper function and cannot continue running safely or correctly until the fault is diagnosed and repaired.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseThe event appears as a controller or instrumentation fault alarm, loss of communication between the PLC and field devices, frozen or out-of-range sensor readings, or an unexpected drive trip, all logged against an automation or instrumentation downtime reason code. Equipment state transitions to fault or stopped, and upstream or downstream machines may show starvation or blocking while the affected station is down for repair.
Gegenmaßnahme
Ingenieurpraktische HinweiseApply preventive calibration, testing and cleaning of sensors, transmitters and control cabinets on a scheduled basis, keep spare I/O cards, drives and critical instruments on hand, and use condition monitoring or diagnostic alarms on control networks to detect degradation before a hard failure occurs. Where the loop is critical to production continuity, add redundancy or voting logic to tolerate a single instrument or module failure.
4Quellen
- Verlustzeit: 2,00 min · laut Bericht: “Instruções ao operador B”
Wörtliches Zitat anzeigen
9 Instruções ao operador B 2 0
- Verlustzeit: 0 min · laut Bericht: “Instruções ao operador B”
Wörtliches Zitat anzeigen
9 Instruções ao operador B 2 0
- Strategic formulation of industrial maintenance based on equipment reliability in a sugar and ethanol production plant (2020)Quelle öffnenZeit zwischen Ereignissen: 6,18 log(min) · laut Bericht: “Maintenance Instrumentation”
Wörtliches Zitat anzeigen
Maintenance Instrumentation 15 6.178 (5.289; 7.067)
- Strategic formulation of industrial maintenance based on equipment reliability in a sugar and ethanol production plant (2020)Quelle öffnenZeit zwischen Ereignissen: 6,24 log(min) · laut Bericht: “Maintenance Industrial Automation”
Wörtliches Zitat anzeigen
Maintenance Industrial Automation 9 6.242 (5.095; 7.390)
- Strategic formulation of industrial maintenance based on equipment reliability in a sugar and ethanol production plant (2020)Quelle öffnenAnzahl der Ereignisse: 9,00 events · laut Bericht: “Maintenance Industrial Automation”
Wörtliches Zitat anzeigen
Maintenance Industrial Automation 9 6.242 (5.095; 7.390)
- Strategic formulation of industrial maintenance based on equipment reliability in a sugar and ethanol production plant (2020)Quelle öffnenAnzahl der Ereignisse: 15,0 events · laut Bericht: “Maintenance Instrumentation”
Wörtliches Zitat anzeigen
Maintenance Instrumentation 15 6.178 (5.289; 7.067)
- ESTRATÉGIA DE MANUTENÇÃO EM UMA USINA DE AÇUCAR E ALCOOL UTILIZANDO MODELO ESTATÍSTICO DE CONFIABILIDADE (2024)Quelle öffnenAnzahl der Ereignisse: 50,0 events · laut Bericht: “Instrumentation (INST)”
Wörtliches Zitat anzeigen
INST 50 47,83 51,52 2653,99 30,00
- ESTRATÉGIA DE MANUTENÇÃO EM UMA USINA DE AÇUCAR E ALCOOL UTILIZANDO MODELO ESTATÍSTICO DE CONFIABILIDADE (2024)Quelle öffnenMittlere Ereignisdauer: 47,8 min · laut Bericht: “Instrumentation (INST)”
Wörtliches Zitat anzeigen
INST 50 47,83 51,52 2653,99 30,00
- Reliability-Centered Maintenance Model to Improve OEE in a Mass-Consumption Food Company: A Case Study from Peru (2025)Quelle öffnenAnteil an der Verlustzeit: 19,0 % · laut Bericht: “instrumentation faults”
Wörtliches Zitat anzeigen
These reasons were linked to specific root causes: mechanical and electrical failures explained 30.2% of the stoppages, while instrumentation faults represented 19%.

