Changeover adjustment time to first good unit
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei weniger als 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 56 % der Verlustzeit der Linie. Berichtet von 0 der 76 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
After a product or format changeover on the forming station, the mould, mandrel or tooling and the process parameters (temperature, pressure, alignment) must be adjusted and stabilised before the machine can produce a conforming form or product. The time and material consumed between the last good unit of the previous run and the first good form or product of the new run is counted as setup and adjustment loss.
Was man dagegen tut
Standardise changeover procedures with predefined set points and tooling positions, use quick-change tooling and automated recipe recall to shorten the adjustment window, and track time and scrap to first good unit as a changeover performance indicator to drive continuous improvement.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,4 % [0,1–1,3 %]
- Erwarteter Anteil an der Verlustzeit
- 0,2 % [0,0–0,7 %]
- Anteil an der Verlustzeit bei Auftreten
- 56 % [44–67 %]
- Studien / Einheiten
- 76 / 96
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,5 % [0,0–2,0 %]5 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,5 % [0,0–1,9 %]11 Studien
- Bier, Wein und Spirituosen0,5 % [0,0–2,0 %]0 Studien
- Backwaren und Teigwaren0,4 % [0,0–1,7 %]25 Studien
- Fleisch, Geflügel und Fisch0,5 % [0,0–1,9 %]3 Studien
- Obst- und Gemüseverarbeitung0,5 % [0,0–2,0 %]3 Studien
- Getreide- und Ölsaatenmüllerei0,5 % [0,0–2,0 %]0 Studien
- Zucker und Süßwaren0,5 % [0,0–1,9 %]8 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,5 % [0,0–1,8 %]7 Studien
- Futtermittel und Heimtiernahrung0,5 % [0,0–1,9 %]6 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,5 % [0,0–2,0 %]8 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseAfter a product or format changeover on the forming station, the mould, mandrel or tooling and the process parameters (temperature, pressure, alignment) must be adjusted and stabilised before the machine can produce a conforming form or product. The time and material consumed between the last good unit of the previous run and the first good form or product of the new run is counted as setup and adjustment loss.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseSCADA/MES shows a changeover or setup machine state bounded by the end-of-run event and a quality or counter event tagged as first good part, with repeated micro-adjustments of set points and no stable production counter increment during this interval. Rejected or scrap counts from trial pieces may accumulate before the first good unit flag is raised.
Gegenmaßnahme
Ingenieurpraktische HinweiseStandardise changeover procedures with predefined set points and tooling positions, use quick-change tooling and automated recipe recall to shorten the adjustment window, and track time and scrap to first good unit as a changeover performance indicator to drive continuous improvement.
4Quellen
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Quelle öffnenMittlere Ereignisdauer: 3,00 min · laut Bericht: “First good form”
Wörtliches Zitat anzeigen
First good form: 0:03:00
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Quelle öffnenMittlere Ereignisdauer: 27,0 min · laut Bericht: “First good product”
Wörtliches Zitat anzeigen
First good product: 0:27:00

