foratvise
Loslegen
Rüsten und Einstellen

Changeover and setup adjustment on grinding mill

Rüsten und EinstellenVerfügbarkeitMahlen und Zerkleinern

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 54 % der Verlustzeit der Linie. Berichtet von 2 der 43 Studien, die sie beobachten konnten (begrenzte Evidenz).

Was passiert

Production stops while the grinding mill is reconfigured between runs: changing grinding plates, screens or rollers, resetting gaps and feed parameters, and fine-tuning the machine until it reaches stable operating conditions for the new product or specification. This elapsed time between the last good unit of the previous run and the first good unit of the next run is non-productive by nature.

Was man dagegen tut

Standardize and document the setup procedure with pre-set gap and feed references per product, use quick-change tooling for plates/screens, and prepare parts and adjustments offline (SMED approach) to shorten the changeover window.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
1,3 % [0,2–3,7 %]
Erwarteter Anteil an der Verlustzeit
0,7 % [0,1–1,9 %]
Anteil an der Verlustzeit bei Auftreten
54 % [42–64 %]
Studien / Einheiten
43 / 48
Evidenzgrad
C

Grad C: 2 bis 4 Studien oder eine Intervallbreite über 0,35.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    1,4 % [0,1–5,3 %]5 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    1,5 % [0,1–5,9 %]1 Studie
  • Bier, Wein und Spirituosen
    1,5 % [0,1–6,0 %]0 Studien
  • Backwaren und Teigwaren
    1,5 % [0,1–5,6 %]0 Studien
  • Fleisch, Geflügel und Fisch
    1,5 % [0,2–6,0 %]0 Studien
  • Obst- und Gemüseverarbeitung
    1,4 % [0,2–5,3 %]2 Studien
  • Getreide- und Ölsaatenmüllerei
    1,4 % [0,1–5,5 %]7 Studien
  • Zucker und Süßwaren
    1,9 % [0,2–6,3 %]10 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    1,3 % [0,1–4,9 %]5 Studien
  • Futtermittel und Heimtiernahrung
    2,0 % [0,2–7,4 %]6 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    1,4 % [0,2–5,1 %]7 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

Production stops while the grinding mill is reconfigured between runs: changing grinding plates, screens or rollers, resetting gaps and feed parameters, and fine-tuning the machine until it reaches stable operating conditions for the new product or specification. This elapsed time between the last good unit of the previous run and the first good unit of the next run is non-productive by nature.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

SCADA/MES shows the mill in a changeover or setup machine-state with the line otherwise idle or starved downstream, bracketed by order or recipe change events; motor running at low or no load with no material throughput logged, followed by a ramp-up period before stable speed and load are reached.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Standardize and document the setup procedure with pre-set gap and feed references per product, use quick-change tooling for plates/screens, and prepare parts and adjustments offline (SMED approach) to shorten the changeover window.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Anteil an der geplanten Zeit: 7,35 % · laut Bericht: “Setup and Adjustment Losses”
    Wörtliches Zitat anzeigen
    = 750 10200 𝑥 100% = 7,353
  2. Anteil an der Verlustzeit: 1,82 % · laut Bericht: “Setup and adjusment losses”
    Wörtliches Zitat anzeigen
    Setup and adjusment losses 6,00 1,82 99,21
  3. Verlustzeit: 6,00 jam · laut Bericht: “Setup and adjusment losses”
    Wörtliches Zitat anzeigen
    Setup and adjusment losses 6,00 1,82 99,21
  4. Anteil an der Verlustzeit: 0,159 % · laut Bericht: “setup and adjustment losses”
    Wörtliches Zitat anzeigen
    Rata-rata kerugian yang terjadi pada setiap mesin yaitu breakdown losses 0,048%, setup and adjustment losses 0,159%, idle and minor stoppages 12,127%, dan reduced speed losses 11,749%.
  5. Anteil an der geplanten Zeit: 4,00 % · laut Bericht: “set up and adjustment”
    Wörtliches Zitat anzeigen
    Rata-rata waktu set up & adjustment losses pada mesin grinding yaitu sebesar 4%.
  6. Verlustzeit: 22,0 jam · laut Bericht: “setup and adjustment”
    Wörtliches Zitat anzeigen
    Setup and adjustment (jam) 22 35 12 18 42 17
  7. Verlustzeit: 35,0 jam · laut Bericht: “setup and adjustment”
    Wörtliches Zitat anzeigen
    Setup and adjustment (jam) 22 35 12 18 42 17
  8. Verlustzeit: 12,0 jam · laut Bericht: “setup and adjustment”
    Wörtliches Zitat anzeigen
    Setup and adjustment (jam) 22 35 12 18 42 17
  9. Verlustzeit: 18,0 jam · laut Bericht: “setup and adjustment”
    Wörtliches Zitat anzeigen
    Setup and adjustment (jam) 22 35 12 18 42 17
  10. Verlustzeit: 42,0 jam · laut Bericht: “setup and adjustment”
    Wörtliches Zitat anzeigen
    Setup and adjustment (jam) 22 35 12 18 42 17
  11. Verlustzeit: 17,0 jam · laut Bericht: “setup and adjustment”
    Wörtliches Zitat anzeigen
    Setup and adjustment (jam) 22 35 12 18 42 17
  12. Verlustzeit: 210 minute · laut Bericht: “setup time (total)”
    Wörtliches Zitat anzeigen
    Time to set up minute 303.54 195 210.02 -30.81%
  13. Verlustzeit: 304 minute · laut Bericht: “setup time (total)”
    Wörtliches Zitat anzeigen
    Time to set up minute 303.54 195 210.02 -30.81%
  14. Anzahl der Ereignisse: 175 times · laut Bericht: “faults”
    Wörtliches Zitat anzeigen
    Number of faults times 243 120 175 -27.98%
  15. Anzahl der Ereignisse: 243 times · laut Bericht: “faults”
    Wörtliches Zitat anzeigen
    Number of faults times 243 120 175 -27.98%
  16. Verlustzeit: 301 minutes · laut Bericht: “setup time (total)”
    Wörtliches Zitat anzeigen
    As a result, the total setup time decreased from 301.28 minutes to 210.02 minutes, representing a 30.81% improvement.
  17. Verlustzeit: 301 minutes · laut Bericht: “internal setup activities”
    Wörtliches Zitat anzeigen
    The total time for internal activities was reduced from 301.28 minutes to 225.21 minutes, representing a 25.63% reduction in downtime, while external tasks remained stable or were improved slightly.
  18. Anteil an der Verlustzeit: 25,0 % · laut Bericht: “frequent operator failures”
    Wörtliches Zitat anzeigen
    At Level 1 of the analysis, the primary causes were identified as high unproductive times (75%) and frequent operator failures (25%).
  19. Anteil an der Verlustzeit: 29,0 % · laut Bericht: “frequent setup stops”
    Wörtliches Zitat anzeigen
    At Level 2, the root causes of unproductive times were mainly attributed to high machine shutdowns due to failure (45.98%) and frequent setup stops (29.02%).
  20. Verlustzeit: 225 minutes · laut Bericht: “internal setup activities”
    Wörtliches Zitat anzeigen
    The total time for internal activities was reduced from 301.28 minutes to 225.21 minutes, representing a 25.63% reduction in downtime, while external tasks remained stable or were improved slightly.
  21. Anteil an der Verlustzeit: 0,730 % · laut Bericht: “setup & adjustment losses”
    Wörtliches Zitat anzeigen
    Sementara itu, breakdown losses sebesar 3,33%, setup & adjustment losses sebesar 0,73%, dan process defect losses sebesar 2,5% tergolong rendah, sehingga tidak menjadi faktor dominan dalam penurunan kinerja mesin.