Eingeschlossene Studie
Implementing Lean and TPM for Machine Availability Enhancement: A Case Study in the Peruvian Food Processing Industry
1Bibliografische Angaben
- Autoren
- Luis Mauricio Mariluz-Cuadros, Brandon Minaya-Sanchez, Alberto Flores-Pérez
- Jahr
- 2025
- Publikationsorgan
- International Conference on Industrial Engineering and Operations Management (IEOM)
- Land
- Peru
- Segment
- Futtermittel und Heimtiernahrung
- Prozessfamilie
- Mahlen, Extrahieren und Trennen
- Studientyp
- Vorher-nachher-Intervention
- Extraktionsumfang
- Volltext
- Umfang
- 1 Werke · 1 Linien · — Maschinen
- Beobachtungszeitraum
- —
- Datenerhebung
- not_reported
- Intervention
Umfeld laut Studie anzeigen
The validation scenario was conducted in a case study of an agricultural production company specializing in the manufacturing of protein flours derived from animal by-products through the process known as rendering.
2Verzerrungsrisiko
Bewertet nach dem Schema des Protokolls: 2 geringe Bedenken, 1 einige Bedenken, 0 hohe Bedenken.
Gesamtpunktzahl 7Hohes Risiko
| Kriterium | Punkte |
|---|---|
| Is the observed line, machine or plant described well enough to classify its segment, process and equipment?Product, process and equipment are all described. | 2 / 2 |
| Is the observation period long enough and reported?Period not reported. | 0 / 2 |
| How were loss data collected?Interviews, estimates, or method not reported. | 0 / 2 |
| Are OEE, loading time and the loss categories defined explicitly?A standard definition is cited but its application is not shown. | 1 / 2 |
| Does the loss breakdown account for the total loss it claims to explain?Only the top causes are reported and the unexplained remainder can be computed. | 1 / 2 |
| Is there evidence of selective reporting of favourable results?Intervention study in which baseline and post-intervention periods differ in length or method. | 1 / 2 |
| Are the reported numbers internally consistent?Small inconsistencies (2 to 10 percentage points) or values that cannot be cross-checked. | 1 / 2 |
| Could conflicts of interest or the source of the data bias the result?Authors are employees of the plant or of an equipment/software vendor; no declaration. | 1 / 2 |
3Extrahierte Daten
Jeder Datenpunkt mit seiner Einordnung und dem wörtlichen Zitat, das ihn belegt.
| Berichtete Ursache | Verlustkategorie | Kennzahl | Wert | Extraktion |
|---|---|---|---|---|
—milling machineWörtliches Zitat anzeigen (Section 4.3 Autonomous Maintenance)Similarly, the mean time between failures (MTBF) increased from 27.27 hours to 39.30 hours, indicating a substantial enhancement in equipment reliability. | Anlagenausfall (Störungen) | Zeit zwischen Ereignissen | 39,3 hours | Durch Schiedsentscheid |
—milling machineWörtliches Zitat anzeigen (Section 4.3 Autonomous Maintenance)The mean time to repair (MTTR) was reduced from 2.36 hours to 1.84 hours, reflecting a 43.96% improvement. | Anlagenausfall (Störungen) | Mittlere Ereignisdauer | 1,84 hours | Durch Schiedsentscheid |
—milling machineWörtliches Zitat anzeigen (Section 4.3 Autonomous Maintenance)Similarly, the mean time between failures (MTBF) increased from 27.27 hours to 39.30 hours, indicating a substantial enhancement in equipment reliability. | Anlagenausfall (Störungen) | Zeit zwischen Ereignissen | 27,3 hours | Durch Schiedsentscheid |
—milling machineWörtliches Zitat anzeigen (Section 4.3 Autonomous Maintenance)The mean time to repair (MTTR) was reduced from 2.36 hours to 1.84 hours, reflecting a 43.96% improvement. | Anlagenausfall (Störungen) | Mittlere Ereignisdauer | 2,36 hours | Durch Schiedsentscheid |
—milling machineWörtliches Zitat anzeigen (Table 1)Availability Rate % 77.01% 90% 82.00% 6.48% | none | Verfügbarkeit | 82,0 % | Beide Extraktionen übereinstimmend |
—milling machineWörtliches Zitat anzeigen (Table 1)Availability Rate % 77.01% 90% 82.00% 6.48% | none | Verfügbarkeit | 77,0 % | Beide Extraktionen übereinstimmend |
setup time (total)milling machineWörtliches Zitat anzeigen (Table 1)Time to set up minute 303.54 195 210.02 -30.81% | Rüsten und Einstellen | Verlustzeit | 210 minute | Beide Extraktionen übereinstimmend |
setup time (total)milling machineWörtliches Zitat anzeigen (Table 1)Time to set up minute 303.54 195 210.02 -30.81% | Rüsten und Einstellen | Verlustzeit | 304 minute | Beide Extraktionen übereinstimmend |
faultsmilling machineWörtliches Zitat anzeigen (Table 1)Number of faults times 243 120 175 -27.98% | Anlagenausfall (Störungen) | Anzahl der Ereignisse | 175 times | Beide Extraktionen übereinstimmend |
faultsmilling machineWörtliches Zitat anzeigen (Table 1)Number of faults times 243 120 175 -27.98% | Anlagenausfall (Störungen) | Anzahl der Ereignisse | 243 times | Beide Extraktionen übereinstimmend |
—milling machineWörtliches Zitat anzeigen (Table 1)MTTR (Average repair time) minute 2.36 1.5 1.84 -22.03% | none | Mittlere Ereignisdauer | 2,36 minute | Einfache Extraktion |
—milling machineWörtliches Zitat anzeigen (Table 1)MTBF (Mean time between failures) minute 27.23 45 39.3 44.33% | none | Zeit zwischen Ereignissen | 27,2 minute | Einfache Extraktion |
setup time (total)milling machineWörtliches Zitat anzeigen (Section 4.3 SMED)As a result, the total setup time decreased from 301.28 minutes to 210.02 minutes, representing a 30.81% improvement. | Rüsten und Einstellen | Verlustzeit | 301 minutes | Einfache Extraktion |
internal setup activitiesmilling machineWörtliches Zitat anzeigen (Section 4.3 SMED / Figure 4)The total time for internal activities was reduced from 301.28 minutes to 225.21 minutes, representing a 25.63% reduction in downtime, while external tasks remained stable or were improved slightly. | Rüsten und Einstellen | Verlustzeit | 301 minutes | Einfache Extraktion |
high unproductive timesmilling machineWörtliches Zitat anzeigen (Section 4.2 / Figure 2)At Level 1 of the analysis, the primary causes were identified as high unproductive times (75%) and frequent operator failures (25%). | Aus dem Bericht nicht klassifizierbar | Anteil an der Verlustzeit | 75,0 % | Einfache Extraktion |
frequent operator failuresmilling machineWörtliches Zitat anzeigen (Section 4.2 / Figure 2)At Level 1 of the analysis, the primary causes were identified as high unproductive times (75%) and frequent operator failures (25%). | Organisatorische oder externe Stillstände (Material- oder Personalmangel, Ausfall der Versorgung) | Anteil an der Verlustzeit | 25,0 % | Einfache Extraktion |
high machine shutdowns due to failuremilling machineWörtliches Zitat anzeigen (Section 4.2)At Level 2, the root causes of unproductive times were mainly attributed to high machine shutdowns due to failure (45.98%) and frequent setup stops (29.02%). | Anlagenausfall (Störungen) | Anteil an der Verlustzeit | 46,0 % | Einfache Extraktion |
frequent setup stopsmilling machineWörtliches Zitat anzeigen (Section 4.2)At Level 2, the root causes of unproductive times were mainly attributed to high machine shutdowns due to failure (45.98%) and frequent setup stops (29.02%). | Rüsten und Einstellen | Anteil an der Verlustzeit | 29,0 % | Einfache Extraktion |
lack of order and cleanliness in the facilitymilling machineWörtliches Zitat anzeigen (Section 4.2)On the other hand, operator failures were linked to a lack of order and cleanliness in the facility (21%). | Organisatorische oder externe Stillstände (Material- oder Personalmangel, Ausfall der Versorgung) | Anteil an der Verlustzeit | 21,0 % | Einfache Extraktion |
—milling machineWörtliches Zitat anzeigen (Table 1)MTTR (Average repair time) minute 2.36 1.5 1.84 -22.03% | none | Mittlere Ereignisdauer | 1,84 minute | Einfache Extraktion |
—milling machineWörtliches Zitat anzeigen (Table 1)MTBF (Mean time between failures) minute 27.23 45 39.3 44.33% | none | Zeit zwischen Ereignissen | 39,3 minute | Einfache Extraktion |
internal setup activitiesmilling machineWörtliches Zitat anzeigen (Section 4.3 SMED / Figure 4)The total time for internal activities was reduced from 301.28 minutes to 225.21 minutes, representing a 25.63% reduction in downtime, while external tasks remained stable or were improved slightly. | Rüsten und Einstellen | Verlustzeit | 225 minutes | Einfache Extraktion |
Beobachtungseinheiten
- Milling machines · Mahlen und Zerkleinern · Nach der Intervention
- Milling machines · Mahlen und Zerkleinern · Ausgangslage

