Cut piece dimension/weight out of customer specification limits
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 48 % der Verlustzeit der Linie. Berichtet von 3 der 39 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
Process variability in the cutting or portioning step, such as blade wear, inconsistent actuator positioning, or raw material size variation, makes the resulting piece dimension or weight drift away from the target. When the process mean shifts or the distribution becomes skewed, an increasing share of pieces falls beyond the upper or lower specification limit set by a given customer.
Was man dagegen tut
Apply statistical process control with corrective adjustment rules to recenter the cutting or portioning process before drift reaches the specification limits, including routine blade maintenance and actuator calibration. Segregate or pre-sort incoming raw material by size when feedstock variability is the dominant driver, and review customer-specific tolerance windows against actual process capability.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,9 % [0,2–2,9 %]
- Erwarteter Anteil an der Verlustzeit
- 0,5 % [0,1–1,4 %]
- Anteil an der Verlustzeit bei Auftreten
- 48 % [36–60 %]
- Studien / Einheiten
- 39 / 48
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte1,1 % [0,1–4,2 %]5 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte1,1 % [0,1–4,5 %]1 Studie
- Bier, Wein und Spirituosen1,1 % [0,1–4,6 %]0 Studien
- Backwaren und Teigwaren1,1 % [0,1–4,5 %]0 Studien
- Fleisch, Geflügel und Fisch1,6 % [0,2–5,9 %]5 Studien
- Obst- und Gemüseverarbeitung1,1 % [0,1–4,0 %]6 Studien
- Getreide- und Ölsaatenmüllerei1,1 % [0,1–4,4 %]3 Studien
- Zucker und Süßwaren1,1 % [0,1–4,4 %]3 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel1,1 % [0,1–4,7 %]3 Studien
- Futtermittel und Heimtiernahrung1,1 % [0,1–4,2 %]5 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)1,1 % [0,1–3,9 %]8 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseProcess variability in the cutting or portioning step, such as blade wear, inconsistent actuator positioning, or raw material size variation, makes the resulting piece dimension or weight drift away from the target. When the process mean shifts or the distribution becomes skewed, an increasing share of pieces falls beyond the upper or lower specification limit set by a given customer.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseStatistical process control charts on the cutting line show the measured dimension or weight distribution shifting or becoming skewed toward one specification limit, with growing counts of individual points beyond USL or LSL for a specific customer product. Downstream checkweigher or inspection stations log corresponding rises in reject or hold counts tied to that product code.
Gegenmaßnahme
Ingenieurpraktische HinweiseApply statistical process control with corrective adjustment rules to recenter the cutting or portioning process before drift reaches the specification limits, including routine blade maintenance and actuator calibration. Segregate or pre-sort incoming raw material by size when feedstock variability is the dominant driver, and review customer-specific tolerance windows against actual process capability.
4Quellen
- Six Sigma application in an Irish meat processing plant to improve process yields (2023)Quelle öffnenFehlerquote: 88,0 % · laut Bericht: “Customer D non-conforming at LSL”
Wörtliches Zitat anzeigen
D | non-conforming at the lower specification limit at 84 and 88%, respectively
- Six Sigma application in an Irish meat processing plant to improve process yields (2023)Quelle öffnenFehlerquote: 84,0 % · laut Bericht: “Customer C non-conforming at LSL”
Wörtliches Zitat anzeigen
C | non-conforming at the lower specification limit at 84 and 88%, respectively
- Six Sigma application in an Irish meat processing plant to improve process yields (2023)Quelle öffnenFehlerquote: 100 % · laut Bericht: “Customer C non-conforming below LSL”
Wörtliches Zitat anzeigen
C | 100% non-conforming, where the results fell largely below the lower specification limit. No over-trimming
- Six Sigma application in an Irish meat processing plant to improve process yields (2023)Quelle öffnenFehlerquote: 20,0 % · laut Bericht: “Customer C non-conforming, left skewed toward LSL”
Wörtliches Zitat anzeigen
C | 20% were non-conforming within the specifications left skewed of the target (i.e. the non-conforming longissimus dorsi were found towards the lower limit (LSL)
- Six Sigma application in an Irish meat processing plant to improve process yields (2023)Quelle öffnenFehlerquote: 20,0 % · laut Bericht: “Customer E outside specification”
Wörtliches Zitat anzeigen
E | 20% outside specifications
- Six Sigma application in an Irish meat processing plant to improve process yields (2023)Quelle öffnenFehlerquote: 16,0 % · laut Bericht: “Customer A non-conforming at USL”
Wörtliches Zitat anzeigen
Outlier observed A customer specification – however, it was the most conforming specification, with only 16% non-conforming in the USL
- Six Sigma application in an Irish meat processing plant to improve process yields (2023)Quelle öffnenFehlerquote: 100 % · laut Bericht: “Customer A outliers non-conforming”
Wörtliches Zitat anzeigen
A | Outliers - 100% non-conforming with the specification requirements
- Six Sigma application in an Irish meat processing plant to improve process yields (2023)Quelle öffnenFehlerquote: 20,0 % · laut Bericht: “Customer E non-conforming, right skewed toward USL”
Wörtliches Zitat anzeigen
E | 20% were non-conforming within the specifications -Right skewed of the target (i.e. that non-conforming were found towards the upper specification limit (USL))

