Schneiden, Aufschneiden und Entbeinen
Transverse cutting of green-bean pods into cut-style pieces (frozen and canned vegetables)
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Schneiden, Aufschneiden und Entbeinen kann höchstens 91 von je 100 geplanten Stunden nutzen. Der Rest entfällt auf Grenzen, die kein Werk vermeiden kann.
- 91höchstens nutzbar
- 9sind physikalische Grenze
Die drei Grenzen, die das festlegen
Laufzeit: bis 94 %
Der Rest sind Stillstände, die Physik oder Vorschrift erzwingen: Reinigung, Umrüsten, Abtauen.
Geschwindigkeit: bis 100 %
Wie nah an ihrer Höchstgeschwindigkeit sie laufen kann, ohne Produkt oder Anlage zu schädigen.
Gutprodukt: bis 97 %
Ein Teil des Produkts liegt auch bei gut beherrschtem Prozess außerhalb der Spezifikation.
Technisches Detail
Unsicherheitsintervalle, physikalische Modelle je Station und Quellen, für alle, die jede Zahl prüfen möchten.
1Szenario
Stemmed green-bean pods (Phaseolus vulgaris) of random length are laid in the pockets of a cutter and cut transversely by knives at a fixed pitch of 25.4 mm (one inch) into the cut style of the U.S. grade standard (pieces from 19 to 70 mm). Because the pod length is not a multiple of the pitch, every pod leaves a remainder at its end; a remainder shorter than 13 mm is a short piece, a defect of the grade standard. The pieces are then blanched and frozen or canned. The same ceilings are applied as an approximation to the slicing of bread and to the cutting of meat (derivation, section 7).
2Ergebnisse
- TheoretischThermodynamic minimum energy per kg: free energy of the new cut surfaces6,57 × 10⁻⁶ [6,36 × 10⁻⁶–6,76 × 10⁻⁶] kJ/kg
- Beste verfügbare TechnikState-of-the-art on-site energy of cutting/slicing for frozen vegetables (DOE)23,3 kJ/kg
- TypischCurrent typical on-site energy of cutting/slicing for frozen vegetables (DOE)39,5 kJ/kg
- New surface created per kg of pods0,0902 [0,0885–0,0916] m²/kg
- Surface free energy of the wet cut faces (surface tension of water)72,8 [71,3–74,2] mJ/m²
- Duration of one cut through the pod at the declared blade speed (not rate-limiting)4,75 [1,94–8,66] ms
- Mean number of pieces per pod (aligned cutter)4,50 [4,03–4,98]
- TheoretischMaximum yield of the cut (zero kerf of a knife blade)1,00
- Best dokumentiertEdible portion after removal of ends, strings and trimmings (USDA refuse)0,880
- Mass share of short pieces, cutter with one pod end registered0,0325 [0,0293–0,0372]
- Count share of short pieces, cutter with one pod end registered0,113 [0,103–0,127]
- Count share of short pieces with a random knife phase (both ends random)0,205 [0,187–0,226]
- Count share of short pieces (aligned) over the U.S. Grade A tolerance1,33 [1,21–1,50]
- TheoretischMaximum OEE quality factor (mass share of conforming pieces, one pod end registered)0,9675 [0,9628–0,9707]
- TypischQuality factor with a random knife phase (both end pieces random)0,935 [0,926–0,941]
- TheoretischMaximum availability (knife changes forced by wear and daily sanitation)0,938 [0,903–0,963]
- TheoretischMaximum performance factor (the cut is not rate-limiting)1,00
- TheoretischPhysics-bounded OEE0,907 [0,873–0,932]
3Obergrenzen je Dimension
- Theoretisch
- Beste verfügbare Technik
- Best dokumentiert
- Typisch
- TheoretischDOE bandwidth study: thermodynamic minimum of cutting/slicing for frozen vegetables set to zero (minimal chemical conversions); this model keeps the very small free energy of the new surfaces · Vergleichswert0 kJ/kg
- TheoretischThermodynamic minimum energy per kg: free energy of the new cut surfaces6,57 × 10⁻⁶ [6,36 × 10⁻⁶–6,76 × 10⁻⁶] kJ/kg
- Beste verfügbare TechnikState-of-the-art on-site energy of cutting/slicing for frozen vegetables (DOE)23,3 kJ/kg
- TypischCurrent typical on-site energy of cutting/slicing for frozen vegetables (DOE)39,5 kJ/kg
- TheoretischMaximum yield of the cut (zero kerf of a knife blade)1,00
- Best dokumentiertEdible portion after removal of ends, strings and trimmings (USDA refuse)0,880
- TheoretischMaximum OEE quality factor (mass share of conforming pieces, one pod end registered)0,9675 [0,9628–0,9707]
- TypischQuality factor with a random knife phase (both end pieces random)0,935 [0,926–0,941]
- TheoretischMaximum availability (knife changes forced by wear and daily sanitation)0,938 [0,903–0,963]
- TheoretischMaximum performance factor (the cut is not rate-limiting)1,00
- TheoretischPhysics-bounded OEE0,907 [0,873–0,932]
4Verlustkaskade
- TheoretischBeste verfügbare TechnikEnergie je Produkteinheit6,57 × 10⁻⁶ [6,36 × 10⁻⁶–6,76 × 10⁻⁶] kJ/kg → 23,3 kJ/kg (Abstand 23,3 kJ/kg)
The thermodynamic minimum is the free energy of the new surfaces: a few millijoules per kilogram, because a 25 mm cut creates only about 0.08 square metres per kilogram. Real knives spend far more: the tissue deforms elastically and plastically before it fractures, the fracture energy of a fibrous tissue is several orders of magnitude above its surface energy, and the blade rubs against the cut faces. The DOE state-of-the-art and typical values also include conveying, alignment, the drives of the cutters and the water sprays that keep knives clean, so the gap between them and the surface energy is almost entirely machine energy, not cutting work.
- TheoretischTypischQualität0,9675 [0,9628–0,9707] → 0,935 [0,926–0,941] (Abstand 0,0330)
With one pod end registered against a stop, only the trailing remainder of each pod can be short. Cutters that take the pods in at a random position relative to the knives leave a random piece at both ends and roughly double the short pieces. Neither is a physical limit in the strict sense: a cutter that measured each pod and divided it into equal pieces would leave none; with the fixed-pitch knives of the scenario the geometric remainder is unavoidable. Ragged or crushed ends from blunt knives and broken pods are further technology losses.
- TheoretischBest dokumentiertAusbeute1,00 → 0,880 (Abstand 0,120)
The cut itself removes no material. The documented edible portion of raw green beans is 88 %: the stem ends, tips, strings and trimmings removed before cutting are a by-product of the preparation, reported as yield and not as an OEE loss.
5Physikalisch begrenzte OEE
- Belegungszeit (ideal)1,000
- VerfügbarkeitFaktor 0,938 [0,903–0,963]0,938 (−0,063)
- LeistungFaktor 1,000,938 (−0,000)
- QualitätFaktor 0,9675 [0,9628–0,9707]0,907 (−0,030)
- Physikalisch begrenzte OEE0,907 [0,873–0,932]
6Vollständige Herleitung
Scope. Stemmed green-bean pods (Phaseolus vulgaris) of random length lie in the pockets of a cutter and are cut transversely by knives at a fixed pitch = 25.4 mm (one inch) into the cut style of the U.S. grade standard for frozen beans (pieces from 19 to 70 mm long). The pieces are then blanched and frozen or canned. This is the operation cutting of the canned- and frozen-vegetable processes. Symbols, values, units, uncertainty distributions and sources are listed in the parameter table generated from config/physics/cutting.yaml.
1. Mass balance — maximum yield
A knife blade separates the tissue without removing any of it: the kerf of a blade is zero, and the juice lost from the two cut cells is negligible. The cut itself therefore keeps all the mass,
Before cutting, the stem ends and tips are removed (snipping). The USDA nutrient database gives a refuse of 12 % for raw green beans ("ends, strings, trimmings"), so the documented edible portion is = 0.88. That share is a by-product of the preparation, like the bran of milling: it is reported as yield and never enters the OEE.
2. Energy balance — minimum energy per unit of product
Thermodynamic minimum. Cutting changes no chemical bond of significance; the only reversible work it requires is the free energy of the new surfaces. Each cut creates two faces of area , so per kilogram
where = 9.5 mm is the pod diameter, the mean number of cuts per pod (section 4), the pod mass (the USDA household measure gives 55 g for ten pods 4 inches long, scaled to the mean length with a constant mass per unit length), and the surface free energy. The faces of a juicy tissue are wetted by cell sap, so is taken as the surface tension of water at the product temperature (IAPWS through CoolProp, 72.8 mJ/m² at 20 °C). With the point values ≈ 0.090 m²/kg and ≈ 6.6 mJ/kg, a millionth of the energy any real cutter uses. The DOE bandwidth study sets the thermodynamic minimum of cutting/slicing to zero; this model keeps the small surface term, as the milling model does.
The energy ceilings. Theoretical: . Best available technique: the state-of-the-art on-site intensity of cutting/slicing for frozen vegetables in the DOE study, 10 Btu/lb (23.3 kJ/kg). Typical: the current typical intensity of the same row, 17 Btu/lb (39.5 kJ/kg). The gap is almost entirely machine energy: elastic and plastic deformation of the tissue before it fractures, a fracture energy of the fibrous tissue several orders of magnitude above its surface energy, friction of the blade against the faces, and, inside the DOE values, conveying, aligning, drives and the water sprays that keep the knives clean.
3. Rate-limiting step
A knife edge moving at crosses the pod in , about 4.75 ms at the declared 2 m/s: the cut itself never limits the rate. The rate of a cutter is set by how fast the pods can be fed and laid in the pockets, a property of the machine, not of the product. The installed feeding rate is therefore the reference of the performance factor and ; no rate ceiling is reported.
4. Process capability — quality ceiling
Geometry of the remainder. A pod of length cut at a fixed pitch gives full pieces and a remainder
Pod lengths are not multiples of the pitch, so every pod leaves a remainder at its end. The U.S. grade standard defines a short piece in cut style as a unit less than = 13 mm long; it is a defect, and Grade A tolerates at most 8.5 % of units (acceptable quality level 7.90 %). Short pieces are therefore the non-conforming units of this operation.
Cutter with one pod end registered. If each pod rests against a stop, its first knife cut is exactly one pitch from the end and only the trailing remainder is random. With pod lengths the expectations per pod are computed by quadrature over (2401 points over ):
Taking the mass of a piece proportional to its length, the quality factor on a mass basis is
When is larger than about half the pitch the remainder is nearly uniform on and . The mean length is the USDA household length of 4 inches (101.6 mm); its spread is a declared assumption (coefficient of variation 0.15–0.25), on which the result hardly depends. With the point values = 0.9675: 3.25 % of the mass and 11.3 % of the pieces are short. The count share is about 1.33 times the Grade A tolerance (output short_count_over_tolerance), which means that short pieces must be graded out after the cutter; they cannot be left in the product.
Cutter with a random knife phase. If the pods enter at a random position relative to the knives, both end pieces are random. For a uniform offset the first piece is exactly uniform on , and the trailing remainder is exactly uniform too, because the convolution of any length distribution with a uniform distribution of width folds into a uniform one. Hence, for pods longer than one pitch,
giving = 0.9345 and a short count share of 20.5 %.
What the bound means. Neither value is a physical limit in the strict sense: a cutter that measured each pod and divided it into equal pieces would leave no short piece. The bound is the physics of the fixed-pitch technology of the scenario, which is the technology of industrial bean cutters; the derivation states it so that the ceiling is not mistaken for a law of nature. Crushed or ragged ends from blunt knives and broken pods are further technology losses (mechanical damage in the grade standard).
5. Unavoidable stops — maximum availability
Knife edges wear against soil, fibres and seeds; a blunt edge crushes the pod and leaves ragged ends, so the knives are changed at an interval set by wear (, declared 8 h) and each change takes (declared 10 min). Plant debris and juice accumulate on knives, pockets and conveyors, and the open equipment is sanitised once per production day (, declared 1 h). The cutter is cleaned by hand or with foam, not in place, so the cleaning model does not apply. Over a production period :
6. Physics-bounded OEE
Scope of the bound. The theoretical label of means physics-bounded under the declared scenario: the ceiling follows from the physics of the operation for the declared product, equipment and schedule, and it is a bound only conditional on those declarations. It follows the common definition of all models: counts only stops required by regulation or forced by a physical mechanism, at their physical minimum duration, plus the start-up they force; is the ratio of the physics-limited ideal cycle to the cycle of the capable process; is the share of conforming units, and mass losses of conforming product are reported only as yield.
The point values and the Monte Carlo intervals over the declared uncertainty of every input are reported in the output table.
7. Assumptions, validity and use for other processes
See the assumption and validity lists generated from the configuration file. The most influential inputs (sensitivity table) are the pitch, the short-piece limit and the mean pod length for quality, and the sanitation time and knife-change frequency for availability.
Use for other processes. The codebook assigns cutting to three processes. For canned and frozen vegetables the model applies directly to cut beans and, with their own pitch and defect limit, to other vegetables cut transversely. For the slicing of bread the same geometry applies as an approximation: a loaf of random length sliced at a fixed pitch leaves end pieces (heels) whose length is the remainder, and with a random phase both ends are random; the share of heels shorter than the minimum slice is then of the mass. For the cutting of frozen meat into portions the remainder of each muscle is the trim of the portioning, again bounded by the same expression for a fixed portion length; the deboning yield, set by the bone share of the carcass, is a mass loss of the preparation reported as yield and is not modelled here. In both cases the availability terms (knife wear and sanitation) carry over as declared values.
References
- U.S. Department of Agriculture, Agricultural Marketing Service. United States Standards for Grades of Frozen Green Beans and Frozen Wax Beans, seventh issue, effective August 19, 1996 (61 FR 37663).
- U.S. Department of Agriculture, Agricultural Research Service. USDA National Nutrient Database for Standard Reference, Release 28, food group 11, record 11052 (Beans, snap, green, raw), 2015.
- van der Sman, R. G. M., Delbaere, S. M., Timmermans, R. A. H. (2026). Modeling of enzyme inactivation and quality changes during blanching of green beans. Current Research in Food Science, 12, 101424. doi:10.1016/j.crfs.2026.101424 (pod diameter)
- U.S. Department of Energy. Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing, 2017 (Table A1-1, frozen vegetables).
- Bell, I. H., Wronski, J., Quoilin, S., Lemort, V. (2014). Pure and pseudo-pure fluid thermophysical property evaluation and the open-source thermophysical property library CoolProp. Industrial & Engineering Chemistry Research, 53, 2498–2508. doi:10.1021/ie4033999
7Parameter und Herkunft
- 4 inch
Mean length of the pods presented to the cutter
Stoffwert · Gleichverteilt 3,5 bis 4,5 inch
Verifiziertes ZitatWörtliches Zitat anzeigen
Measure 2 = 55g: 10 beans (4" long)USDA National Nutrient Database for Standard Reference, Release 28 (2015): Food Group 11, Vegetables and Vegetable Products (nutrient report) (öffnet in neuem Tab). U.S. Department of Agriculture, Agricultural Research Service, Nutrient Data Laboratory, 2015. S. 165. USDA SR28, food group 11 report (sr28fg11.pdf)
- 0,2
Coefficient of variation of the pod length
Szenario · Gleichverteilt 0,15 bis 0,25
Deklarierte AnnahmeNo open source with the length distribution of processing pods was found; declared assumption. For any spread larger than about half the pitch the remainder is nearly uniform and the result hardly depends on it (derivation, section 4).
- 4 inch
Length of the pods of the USDA household measure (sets the linear density with m_10)
Stoffwert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
Measure 2 = 55g: 10 beans (4" long)USDA National Nutrient Database for Standard Reference, Release 28 (2015): Food Group 11, Vegetables and Vegetable Products (nutrient report) (öffnet in neuem Tab). U.S. Department of Agriculture, Agricultural Research Service, Nutrient Data Laboratory, 2015. S. 165. USDA SR28, food group 11 report (sr28fg11.pdf)
- 55 g
Mass of ten pods of the measure length; pod mass m_pod = (m_10 / 10) mu_L / L_10 (constant linear density)
Stoffwert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
Measure 2 = 55g: 10 beans (4" long)USDA National Nutrient Database for Standard Reference, Release 28 (2015): Food Group 11, Vegetables and Vegetable Products (nutrient report) (öffnet in neuem Tab). U.S. Department of Agriculture, Agricultural Research Service, Nutrient Data Laboratory, 2015. S. 165. USDA SR28, food group 11 report (sr28fg11.pdf)
- 9,5 mm
Pod diameter
Stoffwert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
The mean weight of 150 individual segments was 3.32 g (range: 2.16–4.30 g), with an average diameter of 9.5 mm (range: 7.2–11.0 mm).Modeling of enzyme inactivation and quality changes during blanching of green beans (van der Sman, Delbaere, Timmermans; Current Research in Food Science 12: 101424) (öffnet in neuem Tab). Elsevier (open access, CC BY 4.0); full text served by PubMed Central, 2026. doi:10.1016/j.crfs.2026.101424; PMC13217498
- 0,12
Refuse of raw green beans: ends, strings and trimmings (share of the purchased mass)
Vergleichswert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
Beans, snap, green, raw 12% Ends, strings, trimmingsUSDA National Nutrient Database for Standard Reference, Release 28 (2015): Food Group 11, Vegetables and Vegetable Products (nutrient report) (öffnet in neuem Tab). U.S. Department of Agriculture, Agricultural Research Service, Nutrient Data Laboratory, 2015. S. 163. USDA SR28, food group 11 report (sr28fg11.pdf)
- 25,4 mm
Knife pitch (nominal piece length), one inch
Szenario · Fest
Deklarierte AnnahmeProduct decision within the cut style of the U.S. grade standard, 'cut transversely into pieces less than 70 mm (2.75 in) but not less than 19 mm (0.75 in) in length' (usda_ams_frozen_beans_1996, section 52.2322(b)). Declared value.
- 13 mm
Length below which a unit in cut style is a short piece (defect)
Regulatorisch · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
Short piece means a unit in cut style, that is less than 13 mm (0.50 in) in lengthUnited States Standards for Grades of Frozen Green Beans and Frozen Wax Beans (seventh issue, effective August 19, 1996; 61 FR 37663) (öffnet in neuem Tab). U.S. Department of Agriculture, Agricultural Marketing Service, Fruit and Vegetable Division, 1996. S. 7. 7 CFR 52.2321-52.2330 (U.S. grade standards, 61 FR 37663)
- 8,5 %
U.S. Grade A tolerance for short pieces in cut style (percentage of units)
Regulatorisch · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
8.50 7.90 Short Pieces, Cut StyleUnited States Standards for Grades of Frozen Green Beans and Frozen Wax Beans (seventh issue, effective August 19, 1996; 61 FR 37663) (öffnet in neuem Tab). U.S. Department of Agriculture, Agricultural Marketing Service, Fruit and Vegetable Division, 1996. S. 12. 7 CFR 52.2321-52.2330 (U.S. grade standards, 61 FR 37663)
- 20 °C
Temperature of the pods during cutting (sets the surface tension of the cell sap)
Szenario · Gleichverteilt 10 bis 30 °C
Deklarierte Annahme - 10 Btu/lb
State-of-the-art on-site energy intensity of cutting/slicing, frozen vegetables (DOE bandwidth study)
Vergleichswert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
Cutting/slicing 17 10 10 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 56. DOE/EE-1571; OSTI ID 1512366
- 17 Btu/lb
Current typical on-site energy intensity of cutting/slicing, frozen vegetables (DOE bandwidth study)
Vergleichswert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
Cutting/slicing 17 10 10 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 56. DOE/EE-1571; OSTI ID 1512366
- 2 m/s
Speed of the knife edge through the pod
Szenario · Gleichverteilt 1 bis 5 m/s
Deklarierte AnnahmeDeclared order of magnitude of rotary knives; it only shows that the cut lasts milliseconds.
- 24 h
Production period of the availability balance (one production day)
Szenario · Fest
Deklarierte Annahme - 1 h
Daily sanitation of the cutter (removal of debris, washing, sanitising)
Szenario · Gleichverteilt 0,5 bis 1,5 h
Deklarierte AnnahmeOpen equipment cleaned by hand or with foam; the cleaning model (recirculated circuits) does not apply. Declared duration.
- 8 h
Running time between knife changes (edge wear)
Szenario · Gleichverteilt 4 bis 12 h
Deklarierte AnnahmeSet by edge wear against soil and fibres; no open source with a value was found. Declared assumption.
- 10 min
Duration of one knife change
Szenario · Gleichverteilt 5 bis 15 min
Deklarierte Annahme
8Vergleichswerte
| Vergleichswert | Obergrenze | Wert | Herkunft |
|---|---|---|---|
DOE bandwidth study: thermodynamic minimum of cutting/slicing for frozen vegetables set to zero (minimal chemical conversions); this model keeps the very small free energy of the new surfacesWörtliches Zitat anzeigenCutting/slicing 17 10 10 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 56. DOE/EE-1571; OSTI ID 1512366 | Theoretisch | 0 Btu/lb | Verifiziertes Zitat |
U.S. Grade A acceptable quality level for short pieces in cut style: 7.90 % of units. Not compared: a count share of the finished lot (after grading), not a mass-based quality factorWörtliches Zitat anzeigen8.50 7.90 Short Pieces, Cut StyleUnited States Standards for Grades of Frozen Green Beans and Frozen Wax Beans (seventh issue, effective August 19, 1996; 61 FR 37663) (öffnet in neuem Tab). U.S. Department of Agriculture, Agricultural Marketing Service, Fruit and Vegetable Division, 1996. S. 12. 7 CFR 52.2321-52.2330 (U.S. grade standards, 61 FR 37663) | — | 7,9 % | Verifiziertes Zitat |
9Unvermeidbare Stillstände
- Knife changeDeklarierte Annahme
Knife edges wear against soil, fibres and seeds; a blunt edge crushes the pod and leaves ragged ends (mechanical damage in the grade standard), so knives are changed at an interval set by wear.
- Daily sanitationDeklarierte Annahme
Plant debris and juice accumulate on knives, pockets and conveyors; the open equipment is cleaned and sanitised once per production day.
10Annahmen
- Pod lengths are normally distributed (truncated at zero) with the USDA household length as mean; the pitch is fixed. For the cutter with one pod end registered, the expectation over the pod length is computed by quadrature; for a random knife phase both end pieces are exactly uniform on (0, a) for pods longer than one pitch.
- Short pieces are non-conforming units of the cut style and count as quality losses on a mass basis (mass of short pieces over the mass cut); pieces of 13–19 mm are not defects in the grade standard and are kept. Pod mass is proportional to length (constant linear density).
- The thermodynamic minimum is the free energy of the new surfaces with the cut faces wetted by cell sap, taken as the surface tension of pure water at the product temperature (IAPWS through CoolProp); dissolved solutes and the tissue itself would change it slightly, without changing its order of magnitude.
- The cut is not rate-limiting: a knife crosses the pod in milliseconds and the rate is set by feeding and aligning the pods, so P_max = 1 against the installed feeding rate. Availability counts knife changes forced by edge wear and the daily sanitation at declared durations; the open cutter is cleaned by hand or foam, so the cleaning model does not apply.
11Gültigkeitsbereich
- Transverse cutting of green and wax beans into cut style (pieces 19–70 mm) with knives at a fixed pitch.
- Approximation for other products cut at a fixed pitch from pieces of random length (bread slices and end crusts, meat portions from muscles of random length); deboning yield is not modelled.
12Sensitivität
- Length below which a unit in cut style is a short piece (defect)Elastizität -0,069Spearman-ρ —
- Production period of the availability balance (one production day)Elastizität +0,045Spearman-ρ —
- Daily sanitation of the cutter (removal of debris, washing, sanitising)Elastizität -0,044Spearman-ρ -0,77
- Mean length of the pods presented to the cutterElastizität +0,034Spearman-ρ +0,14
- Knife pitch (nominal piece length), one inchElastizität +0,034Spearman-ρ —
- Running time between knife changes (edge wear)Elastizität +0,022Spearman-ρ +0,42
- Duration of one knife changeElastizität -0,022Spearman-ρ -0,39
- Coefficient of variation of the pod lengthElastizität +0,001Spearman-ρ -0,01
- Größe steigt mit dem Parameter
- Größe sinkt mit dem Parameter
13Validierungsprüfungen
- Dimensionsanalyse18 outputs converted to their declared unitsBestanden
- Jeder zitierte Wert an seiner Quelle verifiziert11 verified, 0 failedBestanden
- Kein dokumentierter Wert übertrifft die theoretische GrenzeBestanden
- Obergrenzen in physikalischer ReihenfolgeBestanden
- Anteile zwischen 0 und 1Bestanden
14Verlustursachen in dieser Operation
- Abdomen cut depth/position deviationProzessfehler (Ausschuss und Nacharbeit)0,9 % [0,2–2,8 %]D39 Studien
- Cut piece dimension/weight out of customer specification limitsProzessfehler (Ausschuss und Nacharbeit)0,9 % [0,2–2,9 %]D39 Studien
- Over-trimmingProzessfehler (Ausschuss und Nacharbeit)0,9 % [0,2–2,7 %]D39 Studien
- Waiting time due to line imbalance at cutting stationLeerlauf und Kurzstillstände0,9 % [0,1–2,7 %]D39 Studien
15Literatur
- United States Standards for Grades of Frozen Green Beans and Frozen Wax Beans (seventh issue, effective August 19, 1996; 61 FR 37663) (öffnet in neuem Tab). U.S. Department of Agriculture, Agricultural Marketing Service, Fruit and Vegetable Division, 1996. S. 7. 7 CFR 52.2321-52.2330 (U.S. grade standards, 61 FR 37663)
- USDA National Nutrient Database for Standard Reference, Release 28 (2015): Food Group 11, Vegetables and Vegetable Products (nutrient report) (öffnet in neuem Tab). U.S. Department of Agriculture, Agricultural Research Service, Nutrient Data Laboratory, 2015. S. 165. USDA SR28, food group 11 report (sr28fg11.pdf)
- Modeling of enzyme inactivation and quality changes during blanching of green beans (van der Sman, Delbaere, Timmermans; Current Research in Food Science 12: 101424) (öffnet in neuem Tab). Elsevier (open access, CC BY 4.0); full text served by PubMed Central, 2026. doi:10.1016/j.crfs.2026.101424; PMC13217498
- Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 56. DOE/EE-1571; OSTI ID 1512366
- doi:10.1016/j.crfs.2026.101424 — Pod diameter of green-bean segments.
- doi:10.1021/ie4033999 — Thermophysical property library (surface tension of water).

