foratvise
Loslegen
Anlagenausfall (Störungen)

Forming/blow-moulding machine breakdown

Anlagenausfall (Störungen)VerfügbarkeitFormen, Gießen und Dosieren

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 2 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 58 % der Verlustzeit der Linie. Berichtet von 5 der 76 Studien, die sie beobachten konnten (gute Evidenz).

Was passiert

A mechanical, electrical, pneumatic or hydraulic component of the blow-mould or forming machine (e.g. mould clamping, heater, actuator, drive or control element) degrades or fails, interrupting the forming process until a technician intervenes. The fault is severe enough that the operator cannot clear it alone and maintenance repair or part replacement is required.

Was man dagegen tut

Apply condition-based or preventive maintenance on critical mould, heating, clamping and drive components, track recurring fault codes to identify weak subsystems, and keep critical spare parts available to shorten repair time. Root-cause analysis of repeated breakdowns should drive design or procedural changes to eliminate the failure mode.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
2,3 % [0,7–5,3 %]
Erwarteter Anteil an der Verlustzeit
1,3 % [0,4–3,1 %]
Anteil an der Verlustzeit bei Auftreten
58 % [47–67 %]
Studien / Einheiten
76 / 96
Evidenzgrad
B

Grad B: 5 bis 9 Studien oder eine Intervallbreite zwischen 0,20 und 0,35.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    2,6 % [0,4–8,2 %]5 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    4,2 % [0,8–12,2 %]11 Studien
  • Bier, Wein und Spirituosen
    2,8 % [0,4–9,5 %]0 Studien
  • Backwaren und Teigwaren
    2,5 % [0,5–6,7 %]25 Studien
  • Fleisch, Geflügel und Fisch
    2,7 % [0,4–8,6 %]3 Studien
  • Obst- und Gemüseverarbeitung
    3,7 % [0,5–12,0 %]3 Studien
  • Getreide- und Ölsaatenmüllerei
    2,8 % [0,4–9,4 %]0 Studien
  • Zucker und Süßwaren
    2,3 % [0,4–7,1 %]8 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    2,4 % [0,4–7,3 %]7 Studien
  • Futtermittel und Heimtiernahrung
    2,4 % [0,4–7,6 %]6 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    3,6 % [0,6–11,5 %]8 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

A mechanical, electrical, pneumatic or hydraulic component of the blow-mould or forming machine (e.g. mould clamping, heater, actuator, drive or control element) degrades or fails, interrupting the forming process until a technician intervenes. The fault is severe enough that the operator cannot clear it alone and maintenance repair or part replacement is required.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

SCADA/MES logs a prolonged machine-down or fault state on the forming/blow-mould asset, typically with a specific alarm or fault code and a maintenance work order; downstream filling or conveying equipment shows starvation while upstream feed accumulates or stops. Repeated short recoveries followed by recurrence of the same alarm code indicate an intermittent failure mode rather than a one-off event.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Apply condition-based or preventive maintenance on critical mould, heating, clamping and drive components, track recurring fault codes to identify weak subsystems, and keep critical spare parts available to shorten repair time. Root-cause analysis of repeated breakdowns should drive design or procedural changes to eliminate the failure mode.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Verlustzeit: 125 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 125 130 227 397 132
  2. Verlustzeit: 130 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 125 130 227 397 132
  3. Verlustzeit: 227 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 125 130 227 397 132
  4. Verlustzeit: 397 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 125 130 227 397 132
  5. Verlustzeit: 132 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 125 130 227 397 132
  6. Verlustzeit: 132 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 125 130 227 397 132
  7. Verlustzeit: 397 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 125 130 227 397 132
  8. Verlustzeit: 227 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 125 130 227 397 132
  9. Verlustzeit: 130 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 125 130 227 397 132
  10. Verlustzeit: 125 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 125 130 227 397 132
  11. Anteil an der Verlustzeit: 7,45 % · laut Bericht: “Electrical downtime”
    Wörtliches Zitat anzeigen
    Electrical downtime 0% 15.53% 6.82% 7.45%
  12. Anteil an der Verlustzeit: 21,0 % · laut Bericht: “Mechanical Downtime”
    Wörtliches Zitat anzeigen
    Mechanical Downtime 17.43% 20.14% 25.54% 21.03%
  13. Anteil an der Verlustzeit: 28,0 % · laut Bericht: “equipment failures”
    Wörtliches Zitat anzeigen
    The primary causes of low efficiency are idling and minor stoppages (48%) and equipment failures (28%), both of which are influenced by a lack of preventive maintenance and errors in machine settings.
  14. Verlustzeit: 3.564 menit · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    rata-rata 3.564 193,25 3.757,25