Start-of-production warm-up and adjustment
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei weniger als 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 57 % der Verlustzeit der Linie. Berichtet von 0 der 76 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
At the beginning of a production run the forming equipment must be brought from a cold or stopped condition up to its operating temperature, pressure, speed and dimensional settings; during this period operators make adjustments to feed, mould alignment and process parameters before the process stabilises, which is accounted as setup time rather than running time.
Was man dagegen tut
Apply standardized startup procedures and checklists, pre-heat or pre-condition the equipment ahead of the scheduled start time, and use recipe-driven automatic ramp-up sequences to shorten and make repeatable the warm-up and adjustment period.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,4 % [0,1–1,2 %]
- Erwarteter Anteil an der Verlustzeit
- 0,2 % [0,0–0,7 %]
- Anteil an der Verlustzeit bei Auftreten
- 57 % [44–67 %]
- Studien / Einheiten
- 76 / 96
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,5 % [0,0–2,1 %]5 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,5 % [0,0–1,8 %]11 Studien
- Bier, Wein und Spirituosen0,5 % [0,0–2,2 %]0 Studien
- Backwaren und Teigwaren0,4 % [0,0–1,6 %]25 Studien
- Fleisch, Geflügel und Fisch0,5 % [0,0–1,8 %]3 Studien
- Obst- und Gemüseverarbeitung0,5 % [0,0–2,1 %]3 Studien
- Getreide- und Ölsaatenmüllerei0,5 % [0,0–2,1 %]0 Studien
- Zucker und Süßwaren0,5 % [0,0–1,8 %]8 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,5 % [0,0–1,9 %]7 Studien
- Futtermittel und Heimtiernahrung0,5 % [0,0–1,8 %]6 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,5 % [0,0–2,0 %]8 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseAt the beginning of a production run the forming equipment must be brought from a cold or stopped condition up to its operating temperature, pressure, speed and dimensional settings; during this period operators make adjustments to feed, mould alignment and process parameters before the process stabilises, which is accounted as setup time rather than running time.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseSCADA/MES records a changeover or setup state code active from the line start command until the first stable cycle is confirmed, with ramp-up patterns visible in temperature, pressure or speed setpoints versus actual values, and manual parameter adjustments logged without associated fault alarms.
Gegenmaßnahme
Ingenieurpraktische HinweiseApply standardized startup procedures and checklists, pre-heat or pre-condition the equipment ahead of the scheduled start time, and use recipe-driven automatic ramp-up sequences to shorten and make repeatable the warm-up and adjustment period.
4Quellen
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Quelle öffnenMittlere Ereignisdauer: 3,00 min · laut Bericht: “Start of production”
Wörtliches Zitat anzeigen
Start of production: 0:03:00

