foratvise
Loslegen
Anlagenausfall (Störungen)

Label applicator jam or misfeed

Anlagenausfall (Störungen)VerfügbarkeitEtikettieren und Kennzeichnen

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei weniger als 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 57 % der Verlustzeit der Linie. Berichtet von 0 der 85 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

Labels with excess adhesive stick to the backing web, dispensing plate or guide rails, while labels cut outside the correct length or with dimensional variation fail to register properly and get caught at the peel edge or applicator pads. The resulting tearing, folding or buildup of adhesive residue blocks the label path and stalls the applicator mechanism, so the fault must be cleared and the mechanism cleaned or adjusted before production can resume.

Was man dagegen tut

Control label stock quality and storage conditions to keep adhesive tack and die-cut dimensions within specification, and verify incoming reels against applicator tolerances before loading. Maintain and periodically clean the peel plate, rollers and sensors, and adjust tension, dispensing speed and sensor sensitivity to the specific label format in use.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,4 % [0,1–1,4 %]
Erwarteter Anteil an der Verlustzeit
0,3 % [0,0–0,8 %]
Anteil an der Verlustzeit bei Auftreten
57 % [46–68 %]
Studien / Einheiten
85 / 113
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,5 % [0,0–2,0 %]11 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    0,4 % [0,0–1,5 %]29 Studien
  • Bier, Wein und Spirituosen
    0,5 % [0,0–1,9 %]13 Studien
  • Backwaren und Teigwaren
    0,6 % [0,0–2,3 %]1 Studie
  • Fleisch, Geflügel und Fisch
    0,5 % [0,0–2,1 %]4 Studien
  • Obst- und Gemüseverarbeitung
    0,5 % [0,1–2,0 %]4 Studien
  • Getreide- und Ölsaatenmüllerei
    0,5 % [0,0–2,3 %]3 Studien
  • Zucker und Süßwaren
    0,5 % [0,0–2,1 %]3 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,5 % [0,0–2,1 %]4 Studien
  • Futtermittel und Heimtiernahrung
    0,5 % [0,0–2,2 %]4 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,5 % [0,0–2,2 %]9 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

Labels with excess adhesive stick to the backing web, dispensing plate or guide rails, while labels cut outside the correct length or with dimensional variation fail to register properly and get caught at the peel edge or applicator pads. The resulting tearing, folding or buildup of adhesive residue blocks the label path and stalls the applicator mechanism, so the fault must be cleared and the mechanism cleaned or adjusted before production can resume.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

MES/SCADA logs show repeated short-to-medium downtime events tagged to the label applicator station, often with label sensor or photocell fault codes and a rising missing-label or label-reject counter. The applicator or labeling axis state alternates between running and fault/stopped, while upstream filling or capping may continue briefly causing blocking until the line is halted.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Control label stock quality and storage conditions to keep adhesive tack and die-cut dimensions within specification, and verify incoming reels against applicator tolerances before loading. Maintain and periodically clean the peel plate, rollers and sensors, and adjust tension, dispensing speed and sensor sensitivity to the specific label format in use.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Anzahl der Ereignisse: 1.595 occurrences · laut Bericht: “sticky labels, jammed labels, labels too short or too long, and labels getting caught”
    Wörtliches Zitat anzeigen
    These problems have caused downtime from October to December 2023, with a total downtime of 6448 minutes and a frequency of 1595 occurrences.
  2. Verlustzeit: 6.448 minutes · laut Bericht: “sticky labels, jammed labels, labels too short or too long, and labels getting caught”
    Wörtliches Zitat anzeigen
    These problems have caused downtime from October to December 2023, with a total downtime of 6448 minutes and a frequency of 1595 occurrences.