foratvise
Loslegen
not classifiable

Manual non-value-added tasks

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 57 % der Verlustzeit der Linie. Berichtet von 1 der 112 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

Steps such as visual inspection, manual cap placement and manual staging or storage of finished product are carried out by hand because the line lacks automation for these functions, inserting labor-paced activities into an otherwise machine-paced flow. These tasks do not transform the product and add cycle time and variability that depend on operator availability and pace rather than equipment design rate.

Was man dagegen tut

Automate the manual functions that are feasible, such as vision-based inspection, mechanized cap placement, and conveyorized or robotic handling of finished goods, to remove labor-paced steps from the machine-paced flow. Where full automation is not justified, apply lean workplace design and standardized work to minimize the time and variability these manual tasks introduce.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,6 % [0,1–1,6 %]
Erwarteter Anteil an der Verlustzeit
0,3 % [0,1–0,9 %]
Anteil an der Verlustzeit bei Auftreten
57 % [46–67 %]
Studien / Einheiten
112 / 155
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,6 % [0,1–2,2 %]14 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    0,7 % [0,1–2,5 %]33 Studien
  • Bier, Wein und Spirituosen
    0,6 % [0,1–2,2 %]14 Studien
  • Backwaren und Teigwaren
    0,7 % [0,1–2,6 %]6 Studien
  • Fleisch, Geflügel und Fisch
    0,7 % [0,1–2,5 %]6 Studien
  • Obst- und Gemüseverarbeitung
    0,7 % [0,1–2,5 %]4 Studien
  • Getreide- und Ölsaatenmüllerei
    0,7 % [0,1–2,5 %]4 Studien
  • Zucker und Süßwaren
    0,7 % [0,1–2,6 %]4 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,6 % [0,1–2,4 %]8 Studien
  • Futtermittel und Heimtiernahrung
    0,7 % [0,1–2,4 %]5 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,6 % [0,1–2,2 %]14 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

Steps such as visual inspection, manual cap placement and manual staging or storage of finished product are carried out by hand because the line lacks automation for these functions, inserting labor-paced activities into an otherwise machine-paced flow. These tasks do not transform the product and add cycle time and variability that depend on operator availability and pace rather than equipment design rate.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

Because the activity is manual, SCADA/MES usually shows no equipment fault or alarm associated with the time consumed; the signature appears instead as manual or operator-assisted mode flags, extended idle or semi-automatic state durations between automatic cycles, and cycle-time variability not explained by any machine-state alarm. Throughput counters may show gaps or irregular pacing with no corresponding downtime code.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Automate the manual functions that are feasible, such as vision-based inspection, mechanized cap placement, and conveyorized or robotic handling of finished goods, to remove labor-paced steps from the machine-paced flow. Where full automation is not justified, apply lean workplace design and standardized work to minimize the time and variability these manual tasks introduce.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Verlustzeit: 2,59 h · laut Bericht: “non-value-added tasks (manual inspection, placement of caps, storage of finished products)”
    Wörtliches Zitat anzeigen
    The analysis showed that these inefficiencies resulted in an excessive time consumption of about 2.59 hours in non-value-added tasks.