Packaging Equipment Setup and Adjustment
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 55 % der Verlustzeit der Linie. Berichtet von 3 der 112 Studien, die sie beobachten konnten (begrenzte Evidenz).
Was passiert
During changeover or after drift from target settings, operators must manually adjust packaging machine parameters such as fill measurement, sealing position or mechanical stops to bring the equipment back to a correct running condition. This non-value-added adjustment time occurs between runs or after a product/format change and is not caused by a component breakdown.
Was man dagegen tut
Standardize changeover and adjustment procedures with pre-set recipes, quick-change tooling and go/no-go gauges, and apply SMED principles to separate internal and external setup tasks. Provide operators with guided HMI instructions and target setpoints to reduce the variability and duration of manual adjustments.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 1,0 % [0,3–2,5 %]
- Erwarteter Anteil an der Verlustzeit
- 0,6 % [0,1–1,4 %]
- Anteil an der Verlustzeit bei Auftreten
- 55 % [42–65 %]
- Studien / Einheiten
- 112 / 155
- Evidenzgrad
- C
Grad C: 2 bis 4 Studien oder eine Intervallbreite über 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte1,1 % [0,1–3,7 %]14 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,9 % [0,1–2,7 %]33 Studien
- Bier, Wein und Spirituosen1,5 % [0,2–4,4 %]14 Studien
- Backwaren und Teigwaren1,7 % [0,2–5,9 %]6 Studien
- Fleisch, Geflügel und Fisch1,2 % [0,2–4,1 %]6 Studien
- Obst- und Gemüseverarbeitung1,2 % [0,1–4,3 %]4 Studien
- Getreide- und Ölsaatenmüllerei1,7 % [0,2–6,0 %]4 Studien
- Zucker und Süßwaren1,2 % [0,2–4,0 %]4 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel1,1 % [0,2–3,8 %]8 Studien
- Futtermittel und Heimtiernahrung1,2 % [0,2–4,0 %]5 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)1,1 % [0,1–3,5 %]14 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseDuring changeover or after drift from target settings, operators must manually adjust packaging machine parameters such as fill measurement, sealing position or mechanical stops to bring the equipment back to a correct running condition. This non-value-added adjustment time occurs between runs or after a product/format change and is not caused by a component breakdown.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseThe line or machine state log shows a manual or adjustment mode with operator intervention flags rather than a fault/alarm code, often with repeated short stop-start cycles and parameter change entries clustered around changeover timestamps. Output counters remain near zero while the machine state indicates setup rather than running or faulted.
Gegenmaßnahme
Ingenieurpraktische HinweiseStandardize changeover and adjustment procedures with pre-set recipes, quick-change tooling and go/no-go gauges, and apply SMED principles to separate internal and external setup tasks. Provide operators with guided HMI instructions and target setpoints to reduce the variability and duration of manual adjustments.
4Quellen
- Use of packing equipment efficiency as an estimate of the overall plant effectiveness and as a tool to improve financial results of a food-processing unit (2017)Quelle öffnenAnteil an der Verlustzeit: 23,0 % · laut Bericht: “mechanical adjustments”
Wörtliches Zitat anzeigen
A deeper analysis of non-scheduled maintenance data (Figure 9) shows that major causes of packing equipment failure are related to: electrical failures (26%), unscheduled operational (26%) or mechanical (23%) adjustments, worn parts or equipment breakdown (13%) and automation failures (6%).
- Use of packing equipment efficiency as an estimate of the overall plant effectiveness and as a tool to improve financial results of a food-processing unit (2017)Quelle öffnenAnteil an der Verlustzeit: 26,0 % · laut Bericht: “unscheduled operational adjustments”
Wörtliches Zitat anzeigen
A deeper analysis of non-scheduled maintenance data (Figure 9) shows that major causes of packing equipment failure are related to: electrical failures (26%), unscheduled operational (26%) or mechanical (23%) adjustments, worn parts or equipment breakdown (13%) and automation failures (6%).
- Anteil an der Verlustzeit: 23,9 % · laut Bericht: “failures or adjustments of the packaging machine”
Wörtliches Zitat anzeigen
The total number of failures or adjustments of all machines was 117 h, of which 23.93% were failures or adjustments of the packaging machine.
- Anzahl der Ereignisse: 23,0 events · laut Bericht: “adjustment”
Wörtliches Zitat anzeigen
During the four-week study, the largest number of events involved adjustment (23 events) and five were associated with a failure of the packaging machine.
- Anteil an der Verlustzeit: 2,19 % · laut Bericht: “Measurement Adjustment”
Wörtliches Zitat anzeigen
Measurement Adjustment 2.19% 2.15% 1.49%
- Anteil an der Verlustzeit: 1,49 % · laut Bericht: “Measurement Adjustment”
Wörtliches Zitat anzeigen
Measurement Adjustment 2.19% 2.15% 1.49%
- Penerapan Metode Overall Equipment Effectiveness (OEE) dan Six Big Losses untuk Mengukur Efektivitas Mesin Packing pada PT. Surya Tsabat Mandiri (2023)Quelle öffnenAnteil an der geplanten Zeit: 5,06 % · laut Bericht: “Setup and adjustment”
Wörtliches Zitat anzeigen
3 Setup and adjustment 5,06 16,09 94,63
- Penerapan Metode Overall Equipment Effectiveness (OEE) dan Six Big Losses untuk Mengukur Efektivitas Mesin Packing pada PT. Surya Tsabat Mandiri (2023)Quelle öffnenAnteil an der Verlustzeit: 16,1 % · laut Bericht: “Setup and adjustment”
Wörtliches Zitat anzeigen
3 Setup and adjustment 5,06 16,09 94,63
- Improving Overall Equipment Effectiveness in the Packaging Process of Finished Cattle Feed: A Case Study of an Animal Feed Production Facility (2025)Quelle öffnenVerlustzeit: 11,0 h · laut Bericht: “Frequent stitching adjustments”
Wörtliches Zitat anzeigen
bags stuck on conveyor Before packaging. Bags falling in machinery. Pallet flow issues. lmoroper bag attachment. Frequent stitching adjiustments. Hour 180 40 23 16 11 Cum % 67% 82% 90% 96% 100% 180 40 23 16 11

