Reduced speed operation of forming equipment
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 2 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 63 % der Verlustzeit der Linie. Berichtet von 4 der 76 Studien, die sie beobachten konnten (begrenzte Evidenz).
Was passiert
The forming machine (press, blow-moulder, or forming line) runs below its ideal design rate because of deliberate slow-running, degraded mechanical or pneumatic performance, mould or tooling wear, or constraints imposed by upstream or downstream equipment and material properties. The cumulative gap between actual and ideal cycle time over the run constitutes the loss, even though the machine never fully stops.
Was man dagegen tut
Perform root cause analysis of the speed gap, including mould or tooling condition, servo or pneumatic drive performance, mechanical wear and material feed consistency, and restore or upgrade the limiting component. Validate performance against the rated speed curve and track the cycle time trend to detect recurring drift.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 2,1 % [0,6–5,0 %]
- Erwarteter Anteil an der Verlustzeit
- 1,3 % [0,4–3,2 %]
- Anteil an der Verlustzeit bei Auftreten
- 63 % [51–75 %]
- Studien / Einheiten
- 76 / 96
- Evidenzgrad
- C
Grad C: 2 bis 4 Studien oder eine Intervallbreite über 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte2,4 % [0,3–7,8 %]5 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte2,9 % [0,5–8,7 %]11 Studien
- Bier, Wein und Spirituosen2,5 % [0,3–8,6 %]0 Studien
- Backwaren und Teigwaren2,3 % [0,4–6,1 %]25 Studien
- Fleisch, Geflügel und Fisch3,6 % [0,5–12,2 %]3 Studien
- Obst- und Gemüseverarbeitung2,4 % [0,3–8,3 %]3 Studien
- Getreide- und Ölsaatenmüllerei2,6 % [0,3–8,9 %]0 Studien
- Zucker und Süßwaren2,1 % [0,3–6,3 %]8 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel2,2 % [0,3–7,2 %]7 Studien
- Futtermittel und Heimtiernahrung3,2 % [0,5–10,0 %]6 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)2,3 % [0,3–7,1 %]8 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseThe forming machine (press, blow-moulder, or forming line) runs below its ideal design rate because of deliberate slow-running, degraded mechanical or pneumatic performance, mould or tooling wear, or constraints imposed by upstream or downstream equipment and material properties. The cumulative gap between actual and ideal cycle time over the run constitutes the loss, even though the machine never fully stops.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseMES or SCADA shows the machine continuously in a running state but with actual cycle time, stroke rate or output counter increments persistently above the standard or ideal cycle time, without stop events being logged. Speed setpoint versus actual speed trends diverge, and the OEE performance factor drops while availability remains high.
Gegenmaßnahme
Ingenieurpraktische HinweisePerform root cause analysis of the speed gap, including mould or tooling condition, servo or pneumatic drive performance, mechanical wear and material feed consistency, and restore or upgrade the limiting component. Validate performance against the rated speed curve and track the cycle time trend to detect recurring drift.
4Quellen
- ANALISIS PRODUKTIVITAS MESIN PRESS DENGAN PENDEKATAN OVERALL EQUIPMENT EFFECTIVENESS(OEE) PADAPT. JAPFA COMFEED INDONESIA LAMPUNG (2017)Quelle öffnenAnteil an der Verlustzeit: 85,4 % · laut Bericht: “Reduced speed losses”
Wörtliches Zitat anzeigen
faktor tertinggi untuk total time losses yaitu pada reduced speed losses sebesar 282,85 jam atau 85,40%
- ANALISIS PRODUKTIVITAS MESIN PRESS DENGAN PENDEKATAN OVERALL EQUIPMENT EFFECTIVENESS(OEE) PADAPT. JAPFA COMFEED INDONESIA LAMPUNG (2017)Quelle öffnenVerlustzeit: 283 jam · laut Bericht: “Reduced speed losses”
Wörtliches Zitat anzeigen
faktor tertinggi untuk total time losses yaitu pada reduced speed losses sebesar 282,85 jam atau 85,40%
- ANALYSIS OF THE OVERALL EQUIPMENT EFFECTIVENESS TO MINIMIZE SIX BIG LOSSES OF COOKIE CAPPER MACHINE-A CASE STUDY IN MANUFACTURING INDUSTRY (2020)Quelle öffnenAnteil an der Verlustzeit: 22,8 % · laut Bericht: “Time lost to produce QC rejections”
Wörtliches Zitat anzeigen
Time lost to produce QC rejections 19.16% 24.26% 25.135 22.84%
- ANALYSIS OF THE OVERALL EQUIPMENT EFFECTIVENESS TO MINIMIZE SIX BIG LOSSES OF COOKIE CAPPER MACHINE-A CASE STUDY IN MANUFACTURING INDUSTRY (2020)Quelle öffnenAnteil an der Verlustzeit: 26,2 % · laut Bericht: “Speed loss”
Wörtliches Zitat anzeigen
Speed loss 21.55% 29.65% 27.50% 26.23%
- ANALYSIS OF THE OVERALL EQUIPMENT EFFECTIVENESS TO MINIMIZE SIX BIG LOSSES OF COOKIE CAPPER MACHINE-A CASE STUDY IN MANUFACTURING INDUSTRY (2020)Quelle öffnenAnteil an der Verlustzeit: 11,8 % · laut Bericht: “High FG”
Wörtliches Zitat anzeigen
High FG 35.53% 0% 0% 11.84%
- Anteil an der Verlustzeit: 23,8 % · laut Bericht: “reduced speed losses”
Wörtliches Zitat anzeigen
the three biggest factors that caused the low value of machine effectiveness were idling & minor stoppages losses of 24.61%, yield losses of 24.37%, and reduced speed losses of 23.78%
- Measuring the Efficiency of Contiform Machines with the Overall Equipment Effectiveness Method at PT Tirta Investama Pandaan (2025)Quelle öffnenAnteil an der Verlustzeit: 13,5 % · laut Bericht: “Reduce Speed”
Wörtliches Zitat anzeigen
The Six Big Losses analysis identified the two most dominant major losses, namely idle minor stoppage of 29.82% and reduce speed of 13.53%.
- Analisis Total Productive Maintenance (TPM) dengan Menggunakan Metode Overall Equipment Effectiveness (OEE) pada Mesin Blowing (2025)Quelle öffnenAnteil an der Verlustzeit: 0 % · laut Bericht: “Reduce Speed Losses”
Wörtliches Zitat anzeigen
Rata - rata 6,10 0,95 11,47 0,00 0,00 0,21

