Unspecified filler loss (unclassified cause)
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 59 % der Verlustzeit der Linie. Berichtet von 5 der 120 Studien, die sie beobachten konnten (gute Evidenz).
Was passiert
The source reports aggregate time losses on the filler under generic headings such as equipment, operational or planned losses, without identifying a specific failure mode, adjustment, stoppage reason or defect mechanism. The underlying physical or organisational cause of the lost time cannot be determined from the label alone, so it may correspond to any combination of breakdowns, minor stops, changeovers or scheduled downtime on the filling station.
Was man dagegen tut
Improve downtime data collection by requiring operators or the control system to tag every stop on the filler with a specific reason code (mechanical fault, format change, cleaning, lack of material, etc.) instead of a generic category, and audit the fault-coding structure in the MES. This enables reclassification of historical generic entries into actionable categories such as equipment failure, setup or organizational causes.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 1,4 % [0,4–3,3 %]
- Erwarteter Anteil an der Verlustzeit
- 0,8 % [0,2–2,0 %]
- Anteil an der Verlustzeit bei Auftreten
- 59 % [49–69 %]
- Studien / Einheiten
- 120 / 162
- Evidenzgrad
- B
Grad B: 5 bis 9 Studien oder eine Intervallbreite zwischen 0,20 und 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte2,0 % [0,3–6,0 %]18 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte2,3 % [0,6–5,5 %]44 Studien
- Bier, Wein und Spirituosen1,4 % [0,2–4,5 %]16 Studien
- Backwaren und Teigwaren1,8 % [0,3–6,1 %]0 Studien
- Fleisch, Geflügel und Fisch1,6 % [0,2–4,9 %]6 Studien
- Obst- und Gemüseverarbeitung1,7 % [0,2–5,3 %]4 Studien
- Getreide- und Ölsaatenmüllerei2,3 % [0,4–7,5 %]6 Studien
- Zucker und Süßwaren1,7 % [0,2–5,4 %]3 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel1,6 % [0,2–4,9 %]6 Studien
- Futtermittel und Heimtiernahrung1,6 % [0,2–5,2 %]4 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)1,5 % [0,2–4,7 %]13 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseThe source reports aggregate time losses on the filler under generic headings such as equipment, operational or planned losses, without identifying a specific failure mode, adjustment, stoppage reason or defect mechanism. The underlying physical or organisational cause of the lost time cannot be determined from the label alone, so it may correspond to any combination of breakdowns, minor stops, changeovers or scheduled downtime on the filling station.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseIn SCADA/MES data this appears as time booked against broad loss buckets (equipment, operational, planned) for the filler without a linked fault code, alarm, or state transition detail, making it impossible to tie the duration to a specific machine state or sensor event. Analysts typically see only aggregated downtime totals per shift or per category rather than discrete event records.
Gegenmaßnahme
Ingenieurpraktische HinweiseImprove downtime data collection by requiring operators or the control system to tag every stop on the filler with a specific reason code (mechanical fault, format change, cleaning, lack of material, etc.) instead of a generic category, and audit the fault-coding structure in the MES. This enables reclassification of historical generic entries into actionable categories such as equipment failure, setup or organizational causes.
4Quellen
- An Example Application On Comparison Of Six Sigma And Kaizen From Total Quality Managment Techniquies (2018)Quelle öffnenVerlustzeit: 252.000 litre · laut Bericht: “ilk üç sebep”
Wörtliches Zitat anzeigen
Yukarıdaki Pareto grafiğinin incelenmesi sonucunda, ortaya çıkan ve aşağıda değerlendirmesi yapılan ilk üç sebebin 252.000 litre şurup kaybına neden olarak ortaya çıkan toplam şurup kaybının %88.4 lük kısmını oluşturduğu belirlenmiştir.
- An Example Application On Comparison Of Six Sigma And Kaizen From Total Quality Managment Techniquies (2018)Quelle öffnenAnteil an der Verlustzeit: 88,4 % · laut Bericht: “ilk üç sebep”
Wörtliches Zitat anzeigen
...ortaya çıkan toplam şurup kaybının %88.4 lük kısmını oluşturduğu belirlenmiştir.
- Analisis Produktivitas Mesin Filling Botol Dengan Metode Overal Equipment Effectiveness Dan Failure Mode And Effect Analysis (2023)Quelle öffnenAnteil an den Verlustereignissen: 28,3 % · laut Bericht: “Downtime Losses”
Wörtliches Zitat anzeigen
Reduce Speed Losses with an average proportion of 3.82% and a relative frequency of 39.01%, Downtime Losses with an average of 2.27% and a relative frequency of 28.31%, Defect Losses with an average of 1.58% and a relative frequency of 15.59%, Idle and Minor Stoppage with an average of 1.55% and a relative frequency of 15.85%.
- Analisis Produktivitas Mesin Filling Botol Dengan Metode Overal Equipment Effectiveness Dan Failure Mode And Effect Analysis (2023)Quelle öffnenAnteil an der geplanten Zeit: 2,27 % · laut Bericht: “Downtime Losses”
Wörtliches Zitat anzeigen
Reduce Speed Losses with an average proportion of 3.82% and a relative frequency of 39.01%, Downtime Losses with an average of 2.27% and a relative frequency of 28.31%, Defect Losses with an average of 1.58% and a relative frequency of 15.59%, Idle and Minor Stoppage with an average of 1.55% and a relative frequency of 15.85%.
- Anteil an der Verlustzeit: 12,8 % · laut Bericht: “machine downtime”
Wörtliches Zitat anzeigen
machine downtime was reduced from 12.80% to 4.44%
- Anteil an der Verlustzeit: 4,44 % · laut Bericht: “machine downtime”
Wörtliches Zitat anzeigen
machine downtime was reduced from 12.80% to 4.44%
- Integration of Overall Equipment Effectiveness and Six Sigma Approach to Minimize Product Defect and Machine Downtime (2023)Quelle öffnenAnteil an den Verlustereignissen: 4,00 % · laut Bericht: “No Code”
Wörtliches Zitat anzeigen
No Code 192 4
- Integration of Overall Equipment Effectiveness and Six Sigma Approach to Minimize Product Defect and Machine Downtime (2023)Quelle öffnenAnzahl der Ereignisse: 192 units · laut Bericht: “No Code”
Wörtliches Zitat anzeigen
No Code 192 4
- Integration of Overall Equipment Effectiveness and Six Sigma Approach to Minimize Product Defect and Machine Downtime (2023)Quelle öffnenVerlustzeit: 29,5 h · laut Bericht: “Total Downtime”
Wörtliches Zitat anzeigen
Total Downtime 29.48 2.84
- Enhancing Production Efficiency and Quality in the Carbonated Beverage Industry: A Lean Manufacturing Approach (2024)Quelle öffnenVerlustzeit: 95,0 min · laut Bericht: “Downtime machines”
Wörtliches Zitat anzeigen
Downtime machines (min) 185 95 -48.65%
- Enhancing Production Efficiency and Quality in the Carbonated Beverage Industry: A Lean Manufacturing Approach (2024)Quelle öffnenVerlustzeit: 185 min · laut Bericht: “Downtime machines”
Wörtliches Zitat anzeigen
Downtime machines (min) 185 95 -48.65%
- Lean and RCM-Based Production Model to Improve Operational Efficiency in the Production Line of a Peruvian Dairy SME (2025)Quelle öffnenAnteil an der Verlustzeit: 37,0 % · laut Bericht: “product losses during the filling process”
Wörtliches Zitat anzeigen
The analysis found two main reasons for this inefficiency: unproductive time during the packaging process, which made up 63% of the problem, and product losses during the filling process, which made up the other 37%.
- Lean and RCM-Based Production Model to Improve Operational Efficiency in the Production Line of a Peruvian Dairy SME (2025)Quelle öffnenAnteil an der Verlustzeit: 63,0 % · laut Bericht: “unproductive time during the packaging process”
Wörtliches Zitat anzeigen
The analysis found two main reasons for this inefficiency: unproductive time during the packaging process, which made up 63% of the problem, and product losses during the filling process, which made up the other 37%.
- Verlustzeit: 160 min · laut Bericht: “Planned losses”
Wörtliches Zitat anzeigen
Planned losses (min) 0 160 0 0 0 160 7
- Verlustzeit: 494 min · laut Bericht: “Operational losses”
Wörtliches Zitat anzeigen
Operational losses (min) 278 494 106 53 157 1088 48
- Verlustzeit: 364 min · laut Bericht: “Equipment losses”
Wörtliches Zitat anzeigen
Equipment losses (min) 420 364 24 55 152 1015 44.8

