foratvise
Get Started
Idling and minor stops (micro-stops)

Waiting time for decanter draining between batches

Idling and minor stops (micro-stops)PerformanceSeparation (centrifugation, filtration, membranes)

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 53 % of the line's lost time. Reported by 0 of the 37 studies that could observe it (sparse evidence).

What happens

In batch-wise separation processes the decanter centrifuge must fully discharge the liquid and solid phases of one batch before it can accept feed for the next, so the machine sits idle while residual product drains from the bowl, scroll and discharge ports. This sequential draining step is inherent to batch operation and creates a forced waiting period between consecutive processing cycles rather than a mechanical fault.

What is done about it

Reduce the forced wait by optimizing the discharge sequence and nozzle or valve configuration to shorten drain time, and decouple consecutive batches using buffer or surge tanks, dual feed lines or a second decanter so that draining of one batch overlaps with preparation or feeding of the next.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.7%]
Expected share of lost time
0.3% [0.0–0.9%]
Share of lost time when present
53% [40–65%]
Studies / units
37 / 44
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.0–2.6%]5 studies
  • Soft drinks, bottled water and juices
    0.6% [0.0–2.4%]1 study
  • Brewing, wine and spirits
    0.6% [0.0–2.5%]1 study
  • Bakery and pasta
    0.6% [0.0–2.6%]0 studies
  • Meat, poultry and seafood
    0.6% [0.0–2.6%]2 studies
  • Fruit and vegetable processing
    0.6% [0.0–2.7%]3 studies
  • Grain and oilseed milling
    0.6% [0.0–2.6%]6 studies
  • Sugar and confectionery
    0.6% [0.0–2.4%]3 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.0–2.7%]4 studies
  • Animal feed and pet food
    0.6% [0.0–2.5%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.0–2.6%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

In batch-wise separation processes the decanter centrifuge must fully discharge the liquid and solid phases of one batch before it can accept feed for the next, so the machine sits idle while residual product drains from the bowl, scroll and discharge ports. This sequential draining step is inherent to batch operation and creates a forced waiting period between consecutive processing cycles rather than a mechanical fault.

How it looks in SCADA data

Engineering guidance

SCADA/MES logs show the centrifuge changing to an idle or wait state between batch-run states, with feed flow, bowl speed or torque signals falling to near zero while a drain or standby timer runs before the next batch-start command is issued. Upstream feed vessels may show rising level or accumulation while the decanter is blocked from accepting new material, and the state-duration histogram shows a recurring gap matching the batch cadence.

Countermeasure

Engineering guidance

Reduce the forced wait by optimizing the discharge sequence and nozzle or valve configuration to shorten drain time, and decouple consecutive batches using buffer or surge tanks, dual feed lines or a second decanter so that draining of one batch overlaps with preparation or feeding of the next.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Time between events: 13.0 min · as reported: “waiting time between batches (decanter draining before next batch)”
    Show verbatim quote
    Given the mass flow rate of 3000 kg h−1 for the centrifuge series, the time necessary for processing a 700 kg batch averaged 14 min, followed by the average 13 min of wait time between batches.