foratvise
Get Started
Equipment failure (breakdowns)

Gripper/clamp breakage

Equipment failure (breakdowns)AvailabilityForming, moulding and depositing

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 76 studies that could observe it (sparse evidence).

What happens

The mechanical grippers or clamps that hold and transfer the material or mould during the forming cycle accumulate fatigue from repeated clamping, impact and thermal cycles until a component fractures or deforms beyond function. The break can occur in the gripper jaw, pivot pin, spring or actuating linkage, causing the forming station to lose its grip on the part.

What is done about it

Apply preventive maintenance with periodic inspection and replacement of gripper components based on cycle counts, use wear-resistant materials or hardened pins and jaws, and monitor clamping force or stroke to detect early degradation before fracture occurs.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.7% [0.1–2.1%]
Expected share of lost time
0.4% [0.1–1.2%]
Share of lost time when present
57% [46–67%]
Studies / units
76 / 96
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.9% [0.1–3.2%]5 studies
  • Soft drinks, bottled water and juices
    1.1% [0.1–4.1%]11 studies
  • Brewing, wine and spirits
    0.9% [0.1–3.5%]0 studies
  • Bakery and pasta
    0.7% [0.1–2.4%]25 studies
  • Meat, poultry and seafood
    0.9% [0.1–3.5%]3 studies
  • Fruit and vegetable processing
    0.9% [0.1–3.4%]3 studies
  • Grain and oilseed milling
    0.9% [0.1–3.3%]0 studies
  • Sugar and confectionery
    0.8% [0.1–3.1%]8 studies
  • Snacks, coffee, tea and other foods
    0.8% [0.1–3.0%]7 studies
  • Animal feed and pet food
    0.9% [0.1–3.1%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.9% [0.1–3.2%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The mechanical grippers or clamps that hold and transfer the material or mould during the forming cycle accumulate fatigue from repeated clamping, impact and thermal cycles until a component fractures or deforms beyond function. The break can occur in the gripper jaw, pivot pin, spring or actuating linkage, causing the forming station to lose its grip on the part.

How it looks in SCADA data

Engineering guidance

The SCADA/MES logs an equipment fault alarm or station-stopped state tied to the gripper axis or clamp mechanism, often with a mechanical fault code rather than a sensor fault, followed by an extended downtime state until maintenance replaces the part. Upstream and downstream stations may show starvation or blocking while the forming unit is offline.

Countermeasure

Engineering guidance

Apply preventive maintenance with periodic inspection and replacement of gripper components based on cycle counts, use wear-resistant materials or hardened pins and jaws, and monitor clamping force or stroke to detect early degradation before fracture occurs.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of loss events: 19.0 % · as reported: “Quebra das pinças”
    Show verbatim quote
    Quebra das pinças. Esta causa não foi validada, pois representava apenas de 19 % das ocorrências, já que todo o processo de montagem das caixas e sacos são automáticos.