foratvise
Get Started
Process defects (scrap and rework)

Weight/yield loss during pulping

Process defects (scrap and rework)QualitySeparation (centrifugation, filtration, membranes)

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 1 of the 37 studies that could observe it (sparse evidence).

What happens

During pulping, raw material is mechanically separated into pulp, juice and fibrous/skin waste; part of the usable mass is retained in the discarded fraction, lost as free moisture, or left unextracted due to screen, blade or pressure settings, so the recovered pulp mass is lower than the theoretical yield from the input material.

What is done about it

Optimize and periodically verify pulper screen mesh size, blade clearance and extraction pressure against raw material characteristics, recalibrate scales and flow meters used for mass balance, and adjust process parameters by product lot to minimize fiber/skin retention and moisture carryover.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.9% [0.1–2.8%]
Expected share of lost time
0.5% [0.1–1.4%]
Share of lost time when present
48% [36–59%]
Studies / units
37 / 44
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.1% [0.1–4.5%]5 studies
  • Soft drinks, bottled water and juices
    1.1% [0.1–4.6%]1 study
  • Brewing, wine and spirits
    1.1% [0.1–4.8%]1 study
  • Bakery and pasta
    1.1% [0.1–4.4%]0 studies
  • Meat, poultry and seafood
    1.1% [0.1–4.6%]2 studies
  • Fruit and vegetable processing
    1.6% [0.1–5.9%]3 studies
  • Grain and oilseed milling
    1.1% [0.1–4.3%]6 studies
  • Sugar and confectionery
    1.1% [0.1–4.6%]3 studies
  • Snacks, coffee, tea and other foods
    1.1% [0.1–4.3%]4 studies
  • Animal feed and pet food
    1.1% [0.1–4.2%]5 studies
  • Food manufacturing (unspecified or mixed)
    1.1% [0.1–4.2%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During pulping, raw material is mechanically separated into pulp, juice and fibrous/skin waste; part of the usable mass is retained in the discarded fraction, lost as free moisture, or left unextracted due to screen, blade or pressure settings, so the recovered pulp mass is lower than the theoretical yield from the input material.

How it looks in SCADA data

Engineering guidance

Mass balance reports from load cells or flow meters show recovered pulp output consistently below the expected ratio relative to metered raw material input, with a declining yield percentage trend rather than discrete stop events; no equipment fault or downtime alarm is associated with the loss.

Countermeasure

Engineering guidance

Optimize and periodically verify pulper screen mesh size, blade clearance and extraction pressure against raw material characteristics, recalibrate scales and flow meters used for mass balance, and adjust process parameters by product lot to minimize fiber/skin retention and moisture carryover.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Defect rate: 20.0 % · as reported: “weight loss in pulping”
    Show verbatim quote
    it should be noted that in the initial diagnosis, a 20% weight loss was lost within the process, in the pulping area.