foratvise
Get Started
Setup and adjustments

Screw conveyor start-up/shutdown and cleaning sequence during changeover

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 56 % of the line's lost time. Reported by 0 of the 37 studies that could observe it (sparse evidence).

What happens

During product changeovers the screw conveyors that feed or connect the press, dryer and cooker must be stopped, emptied and cleaned, and then restarted in a defined order before the next run can resume; this coordinated sequencing and cleaning of multiple conveyor sections consumes non-productive changeover time. The delay is organizational/procedural rather than a mechanical failure, arising from the number of steps and the need to clear material from each conveyor section.

What is done about it

Standardize and document the start-up/shutdown and cleaning sequence for each conveyor section with checklists or interlocked automatic sequencing logic, and design conveyors with quick-clean or self-emptying features to shorten the procedure. Training operators on the fixed sequence and pre-staging cleaning tools also reduces the time lost in this step.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.7%]
Expected share of lost time
0.3% [0.0–1.0%]
Share of lost time when present
56% [43–66%]
Studies / units
37 / 44
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.0–2.5%]5 studies
  • Soft drinks, bottled water and juices
    0.6% [0.0–2.6%]1 study
  • Brewing, wine and spirits
    0.6% [0.0–2.7%]1 study
  • Bakery and pasta
    0.6% [0.0–2.7%]0 studies
  • Meat, poultry and seafood
    0.6% [0.0–2.4%]2 studies
  • Fruit and vegetable processing
    0.6% [0.0–2.5%]3 studies
  • Grain and oilseed milling
    0.6% [0.0–2.4%]6 studies
  • Sugar and confectionery
    0.6% [0.0–2.4%]3 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.0–2.2%]4 studies
  • Animal feed and pet food
    0.6% [0.0–2.4%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.0–2.6%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During product changeovers the screw conveyors that feed or connect the press, dryer and cooker must be stopped, emptied and cleaned, and then restarted in a defined order before the next run can resume; this coordinated sequencing and cleaning of multiple conveyor sections consumes non-productive changeover time. The delay is organizational/procedural rather than a mechanical failure, arising from the number of steps and the need to clear material from each conveyor section.

How it looks in SCADA data

Engineering guidance

SCADA/MES logs show a cluster of motor start and stop events on the screw conveyor drives occurring close together in time, with run-state signals toggling off then on across the press, dryer and cooker feed lines while material flow and downstream production counters remain flat. The event window is typically flagged as a changeover or setup state rather than an unplanned stop alarm.

Countermeasure

Engineering guidance

Standardize and document the start-up/shutdown and cleaning sequence for each conveyor section with checklists or interlocked automatic sequencing logic, and design conveyors with quick-clean or self-emptying features to shorten the procedure. Training operators on the fixed sequence and pre-staging cleaning tools also reduces the time lost in this step.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 16.2 s · as reported: “Encender transportadores helicoidales conectados al secador”
    Show verbatim quote
    Encender transportadores helicoidales conectados al secador 16,2
  2. Lost time: 9.00 s · as reported: “Apagar los transportadores helicoidales conectados a la prensa”
    Show verbatim quote
    Apagar los transportadores helicoidales conectados a la prensa 9
  3. Lost time: 185 s · as reported: “Limpiar los transportadores helicoidales que conectan con la prensa”
    Show verbatim quote
    Limpiar los transportadores helicoidales que conectan con la prensa 185, 4
  4. Lost time: 185 s · as reported: “Limpiar los transportadores helicoidales conectados al secador”
    Show verbatim quote
    Limpiar los transportadores helicoidales conectados al secador 184, 6
  5. Lost time: 10.2 s · as reported: “Apagar los transportadores helicoidales conectados al secador”
    Show verbatim quote
    Apagar los transportadores helicoidales conectados al secador 10,2
  6. Lost time: 18.6 s · as reported: “Encender lo transportadores helicoidales que alimentan la prensa”
    Show verbatim quote
    Encender lo transportadores helicoidales que alimentan la prensa 18,6
  7. Lost time: 107 s · as reported: “Encender el transportador helicoidal que alimenta al cocinador”
    Show verbatim quote
    Encender el transportador helicoidal que alimenta al cocinador 106, 5