foratvise
Get Started
Setup and adjustments

Tooling preparation and transport delay for changeover

Setup and adjustmentsAvailabilityForming, moulding and depositing

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 0 of the 76 studies that could observe it (sparse evidence).

What happens

During a format or product changeover the required dies, molds or tooling for the press are not staged at the point of use, so operators must locate, retrieve and physically carry them from a storage area before the new setup can begin. This logistics step is performed as internal setup time, while the press remains stopped and waiting, extending the overall changeover duration.

What is done about it

Apply SMED principles by converting this logistics step into external setup: pre-stage the next job's tooling, carts and fixtures next to the press while the current run is still producing, using kitted tool trolleys, labeled storage locations and a standardized retrieval sequence. Schedule a dedicated handler or forklift pass synchronized with the production schedule so tooling arrives at the press before the machine is stopped.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.3%]
Expected share of lost time
0.2% [0.0–0.7%]
Share of lost time when present
57% [45–67%]
Studies / units
76 / 96
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.5% [0.0–1.9%]5 studies
  • Soft drinks, bottled water and juices
    0.5% [0.0–1.8%]11 studies
  • Brewing, wine and spirits
    0.5% [0.0–2.1%]0 studies
  • Bakery and pasta
    0.4% [0.0–1.6%]25 studies
  • Meat, poultry and seafood
    0.5% [0.0–2.0%]3 studies
  • Fruit and vegetable processing
    0.5% [0.0–1.9%]3 studies
  • Grain and oilseed milling
    0.5% [0.0–2.0%]0 studies
  • Sugar and confectionery
    0.5% [0.0–1.9%]8 studies
  • Snacks, coffee, tea and other foods
    0.5% [0.0–1.8%]7 studies
  • Animal feed and pet food
    0.5% [0.0–1.9%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.5% [0.0–2.1%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During a format or product changeover the required dies, molds or tooling for the press are not staged at the point of use, so operators must locate, retrieve and physically carry them from a storage area before the new setup can begin. This logistics step is performed as internal setup time, while the press remains stopped and waiting, extending the overall changeover duration.

How it looks in SCADA data

Engineering guidance

The press shows an extended setup or idle machine-state with zero cycles and no active fault or alarm, preceding the first cycle of the new run. The pause duration correlates with operator presence/movement logs or manual changeover timestamps rather than with any equipment fault code, and the same transition recurs identically at every changeover between runs requiring different tooling.

Countermeasure

Engineering guidance

Apply SMED principles by converting this logistics step into external setup: pre-stage the next job's tooling, carts and fixtures next to the press while the current run is still producing, using kitted tool trolleys, labeled storage locations and a standardized retrieval sequence. Schedule a dedicated handler or forklift pass synchronized with the production schedule so tooling arrives at the press before the machine is stopped.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 112 s · as reported: “Prepare and transport tools to press”
    Show verbatim quote
    14 Preparar y trasladar herramientas a la prensa 111,8 X