foratvise
Get Started
Equipment failure (breakdowns)

Washing/filling machine component failure

Equipment failure (breakdowns)AvailabilityContainer washing and rinsing

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 2 of the 80 studies that could observe it (limited evidence).

What happens

Mechanical or structural parts of the washing station and associated filler hardware (drive assemblies, pumps, infeed sections, panels, and small fasteners such as retaining washers or snap rings) wear, loosen or break under cyclic load and exposure to water, detergent or vibration. Their failure removes a required function of the machine, so the unit stops until the part is replaced or repaired.

What is done about it

Apply a preventive and predictive maintenance program covering drive, pump and panel subsystems, including periodic replacement of wear-prone fasteners such as retaining washers and snap rings before they fail. Use vibration, current and pressure monitoring to trigger condition-based replacement, and keep critical spare parts on hand to shorten repair time.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.0% [0.2–2.6%]
Expected share of lost time
0.6% [0.1–1.5%]
Share of lost time when present
58% [47–68%]
Studies / units
80 / 102
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.1% [0.1–3.8%]10 studies
  • Soft drinks, bottled water and juices
    1.2% [0.2–3.5%]27 studies
  • Brewing, wine and spirits
    1.5% [0.2–5.1%]12 studies
  • Bakery and pasta
    1.2% [0.1–4.1%]0 studies
  • Meat, poultry and seafood
    1.1% [0.1–4.0%]4 studies
  • Fruit and vegetable processing
    1.1% [0.1–4.3%]4 studies
  • Grain and oilseed milling
    1.2% [0.1–4.3%]3 studies
  • Sugar and confectionery
    1.2% [0.1–4.2%]3 studies
  • Snacks, coffee, tea and other foods
    1.1% [0.1–3.8%]4 studies
  • Animal feed and pet food
    1.2% [0.1–4.5%]4 studies
  • Food manufacturing (unspecified or mixed)
    1.1% [0.1–3.9%]9 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Mechanical or structural parts of the washing station and associated filler hardware (drive assemblies, pumps, infeed sections, panels, and small fasteners such as retaining washers or snap rings) wear, loosen or break under cyclic load and exposure to water, detergent or vibration. Their failure removes a required function of the machine, so the unit stops until the part is replaced or repaired.

How it looks in SCADA data

Engineering guidance

SCADA/MES logs show an unplanned stop state attributed to the specific washer or drive subsystem tag, often preceded by motor current, pressure or vibration trending out of normal range, or by a discrete fault/interlock alarm (drive fault, pump trip, panel interlock open). Downstream filling or packaging stations show starvation while the washing station remains in fault state until a maintenance work order clears it.

Countermeasure

Engineering guidance

Apply a preventive and predictive maintenance program covering drive, pump and panel subsystems, including periodic replacement of wear-prone fasteners such as retaining washers and snap rings before they fail. Use vibration, current and pressure monitoring to trigger condition-based replacement, and keep critical spare parts on hand to shorten repair time.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 1,140 min · as reported: “main drive washer”
    Show verbatim quote
    main drive washer 26 1140 297 6909 93.40 83.00
  2. Number of events: 26.0 events · as reported: “main drive washer”
    Show verbatim quote
    main drive washer 26 1140 297 6909 93.40 83.00
  3. Lost time: 635 min · as reported: “infeed washer”
    Show verbatim quote
    infeed washer 36 635 271 5769 85.22 69.31
  4. Number of events: 36.0 events · as reported: “infeed washer”
    Show verbatim quote
    infeed washer 36 635 271 5769 85.22 69.31
  5. Lost time: 400 min · as reported: “panel washer”
    Show verbatim quote
    panel washer 1 400 317 8309 99.69 99.82
  6. Number of events: 1.00 events · as reported: “panel washer”
    Show verbatim quote
    panel washer 1 400 317 8309 99.69 99.82
  7. Lost time: 395 min · as reported: “case washer”
    Show verbatim quote
    case washer 11 395 308 7304 96.86 87.75
  8. Number of events: 11.0 events · as reported: “case washer”
    Show verbatim quote
    case washer 11 395 308 7304 96.86 87.75
  9. Lost time: 270 min · as reported: “pump washer”
    Show verbatim quote
    pump washer 1 270 316 7909 99.37 95.01
  10. Number of events: 1.00 events · as reported: “pump washer”
    Show verbatim quote
    pump washer 1 270 316 7909 99.37 95.01
  11. Time between events: 34,555 not reported · as reported: “Snap Ring Washer”
    Show verbatim quote
    Waktu Kerusakan Weibull MTTF 34555,2
  12. Time between events: 29.1 not reported · as reported: “Pull Spring Washer”
    Show verbatim quote
    Waktu Kerusakan Weibull MTTF 29,126
  13. Mean event duration: 200 not reported · as reported: “Pull Spring Washer”
    Show verbatim quote
    Waktu Perbaikan Weibull MTTR 200
  14. Mean event duration: 115 not reported · as reported: “Snap Ring Washer”
    Show verbatim quote
    Waktu Perbaikan Weibull MTTR 114,5
  15. Share of lost time: 35.0 % · as reported: “mechanical failure in washing section”
    Show verbatim quote
    the main causes of the losses in production are stated as mechanical failure in washing section which covers the largest portion (35%), maintenance strategy followed by the plant (27%), maintenance management program (25%), and high cost of maintenance inventory control, and other (13%).