Cambio de formato/molde en equipo de formado
En resumen
Aparece en cerca de 1 de cada 100 líneas estudiadas.
Cuando aparece, se lleva en promedio cerca del 58 % del tiempo perdido de la línea. La reportan 3 de los 76 estudios que podían observarla (evidencia limitada).
Qué pasa
Cambiar la máquina de formado de un formato o producto a otro requiere detener la producción para desmontar y montar moldes, utillaje o piezas de formado, reajustar los parámetros dimensionales y de proceso, y verificar las primeras unidades conformes antes de reanudar la marcha. El tiempo transcurrido entre la última unidad buena del formato anterior y la primera unidad buena del nuevo formato se pierde para la producción.
Qué se hace
Aplicar metodología SMED para separar las actividades internas de las externas en la preparación, estandarizar y preparar previamente el utillaje, emplear dispositivos de cambio rápido y referencias de posicionamiento, y documentar una secuencia repetible para reajustar la máquina de formado con el mínimo tiempo de parada.
Orientación práctica basada en conocimiento de ingeniería; no es una estimación estadística.
1Probabilidad y evidencia
- Probabilidad de presencia
- 1.3 % [0.3–3.2 %]
- Proporción esperada del tiempo perdido
- 0.7 % [0.2–1.9 %]
- Proporción del tiempo perdido cuando está presente
- 58 % [46–68 %]
- Estudios / unidades
- 76 / 96
- Grado de evidencia
- C
Grado C: de 2 a 4 estudios, o un intervalo de ancho mayor a 0,35.
2Probabilidad por segmento
- Productos lácteos2.1 % [0.3–7.4 %]5 estudios
- Refrescos, agua embotellada y jugos1.3 % [0.2–4.5 %]11 estudios
- Cerveza, vino y destilados1.6 % [0.2–6.0 %]0 estudios
- Panadería y pastas1.6 % [0.3–4.7 %]25 estudios
- Carne, aves y pescado1.5 % [0.2–5.2 %]3 estudios
- Procesamiento de frutas y vegetales1.5 % [0.2–5.1 %]3 estudios
- Molienda de granos y oleaginosas1.5 % [0.2–5.2 %]0 estudios
- Azúcar y confitería1.9 % [0.3–6.4 %]8 estudios
- Snacks, café, té y otros alimentos1.4 % [0.2–4.6 %]7 estudios
- Alimento animal y para mascotas1.4 % [0.2–4.7 %]6 estudios
- Manufactura de alimentos (sin especificar o mixta)1.4 % [0.2–4.6 %]8 estudios
3Mecanismo, firma en SCADA y contramedida
Mecanismo
Guía de ingenieríaCambiar la máquina de formado de un formato o producto a otro requiere detener la producción para desmontar y montar moldes, utillaje o piezas de formado, reajustar los parámetros dimensionales y de proceso, y verificar las primeras unidades conformes antes de reanudar la marcha. El tiempo transcurrido entre la última unidad buena del formato anterior y la primera unidad buena del nuevo formato se pierde para la producción.
Cómo se ve en los datos de SCADA
Guía de ingenieríaEl SCADA/MES muestra un estado de máquina parada sostenido, etiquetado como cambio de formato o preparación, delimitado entre el fin de la orden de producción anterior y el inicio de la nueva, sin alarmas de fallo activas; los contadores asociados de cambios de molde o utillaje y los registros de inicio del procedimiento de cambio suelen coincidir con la parada.
Contramedida
Guía de ingenieríaAplicar metodología SMED para separar las actividades internas de las externas en la preparación, estandarizar y preparar previamente el utillaje, emplear dispositivos de cambio rápido y referencias de posicionamiento, y documentar una secuencia repetible para reajustar la máquina de formado con el mínimo tiempo de parada.
4Fuentes
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Abrir fuenteDuración media del evento: 210 min · según el reporte: “changeover (selected type, average, long-run)”
Ver cita textual
The new changeover time was even lower than the project goal, but in the long run, the time was 210 minutes. This time is kept without any major problems.
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Abrir fuenteNúmero de eventos: 58.0 events/year · según el reporte: “changeover (selected type, annual frequency)”
Ver cita textual
At a frequency of 58 changeovers per year and with a given number of operators and wage rates, the annual savings would be 91 thousand. CZK.
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Abrir fuenteDuración media del evento: 244 min · según el reporte: “changeover (selected type, average)”
Ver cita textual
The project team decided on the main goal of the project, which was to reduce the time of the selected sort by 10% of the average changeover time, from 244 minutes to 220 minutes.
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Abrir fuenteDuración media del evento: 185 min · según el reporte: “changeover (most frequent type)”
Ver cita textual
Of these types of changeovers, the fourth longest changeover was the most frequent (which would take 185 minutes), but the longest and second most frequent type of changeover (240 minutes) was eventually chosen by project team for the next step.
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Abrir fuenteDuración media del evento: 240 min · según el reporte: “changeover (selected type for SMED project)”
Ver cita textual
Of these types of changeovers, the fourth longest changeover was the most frequent (which would take 185 minutes), but the longest and second most frequent type of changeover (240 minutes) was eventually chosen by project team for the next step.
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Abrir fuenteDuración media del evento: 194 min · según el reporte: “changeover (selected type, average, first re-measurement)”
Ver cita textual
The average throw time dropped from 244 minutes to 194 minutes (Figure 7) and the target was met.
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Abrir fuenteDuración media del evento: 4.00 min · según el reporte: “Exchange of molds”
Ver cita textual
Exchange of molds: 0:04:00
- CHANGEOVER TIME REDUCTION THROUGH LEAN TOOL “SMED” – A CASE STUDY FROM FOOD SECTOR (2018)Abrir fuenteDuración media del evento: 7.00 min · según el reporte: “Forming of molds”
Ver cita textual
Forming of molds: 0:07:00
- Application of Lean-Total Productive Maintenance Tools to Reduce Setup Times and Machine Stoppages on the Molding Line of an SME in the Food Industry (2023)Abrir fuenteTiempo perdido: 280 min · según el reporte: “Total duration of mold change”
Ver cita textual
From the data collection of the total duration of mold change times, a total of 280 minutes on average was obtained, and the times of internal activities, 254 min, and external activities, 26 min.
- Improvement Model for the Production Area to increase Labor Productivity through Lean Manufacturing tools in a bakery company (2026)Abrir fuenteTiempo perdido: 82.0 min · según el reporte: “format changeovers (changing from circular to rectangular cookies)”
Ver cita textual
It was documented that the setup time averages 1.37 hours per day (82 minutes), consuming a significant portion of the available shift time.
- Improving Production Efficiency in a Chocolate SME through Continuous Flow, SMED and Poka-Yoke (2026)Abrir fuenteNúmero de eventos: 10.0 events/week · según el reporte: “operational interruptions during mold changeover”
Ver cita textual
As-Is interruptions: 10 per week → 1 per week
- Improving Production Efficiency in a Chocolate SME through Continuous Flow, SMED and Poka-Yoke (2026)Abrir fuenteNúmero de eventos: 1.00 events/week · según el reporte: “operational interruptions during mold changeover”
Ver cita textual
Week 5: 1 interruption
- Improving Production Efficiency in a Chocolate SME through Continuous Flow, SMED and Poka-Yoke (2026)Abrir fuenteNúmero de eventos: 5.00 events/week · según el reporte: “operational interruptions during mold changeover”
Ver cita textual
Week 1: 5 interruptions
- Improving Production Efficiency in a Chocolate SME through Continuous Flow, SMED and Poka-Yoke (2026)Abrir fuenteNúmero de eventos: 3.00 events/week · según el reporte: “operational interruptions during mold changeover”
Ver cita textual
Weeks 2, 3, and 4 stabilized at three interruptions each, showing improved workflow continuity and reduced operational stops.

