Blow Molding Container Defects
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 48 % der Verlustzeit der Linie. Berichtet von 3 der 76 Studien, die sie beobachten konnten (begrenzte Evidenz).
Was passiert
During the blowing stage preforms are reheated and stretched against the mold under pneumatic pressure; uneven preform temperature, incorrect blow pressure or timing, or worn mold halves cause containers to come out with thin or uneven wall sections, deformation, haze, flash lines or incomplete forming. These out-of-specification bottles are separated from the good output as first-pass defects rather than reworked inline.
Was man dagegen tut
Calibrate and periodically verify the preform heating profile, blow pressure staging and mold cooling circuits, and perform preventive maintenance and inspection of mold halves and valves to prevent wear-related defects. Implement statistical monitoring of wall-thickness and visual inspection results to detect drift before it generates sustained defect rates.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 1,0 % [0,2–2,7 %]
- Erwarteter Anteil an der Verlustzeit
- 0,5 % [0,1–1,3 %]
- Anteil an der Verlustzeit bei Auftreten
- 48 % [36–60 %]
- Studien / Einheiten
- 76 / 96
- Evidenzgrad
- C
Grad C: 2 bis 4 Studien oder eine Intervallbreite über 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte1,2 % [0,1–4,2 %]5 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte2,2 % [0,3–7,7 %]11 Studien
- Bier, Wein und Spirituosen1,2 % [0,1–4,7 %]0 Studien
- Backwaren und Teigwaren1,0 % [0,1–3,2 %]25 Studien
- Fleisch, Geflügel und Fisch1,2 % [0,1–4,4 %]3 Studien
- Obst- und Gemüseverarbeitung1,2 % [0,1–4,2 %]3 Studien
- Getreide- und Ölsaatenmüllerei1,2 % [0,1–4,7 %]0 Studien
- Zucker und Süßwaren1,1 % [0,1–4,0 %]8 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel1,1 % [0,1–4,2 %]7 Studien
- Futtermittel und Heimtiernahrung1,1 % [0,1–4,1 %]6 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)1,1 % [0,1–4,0 %]8 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseDuring the blowing stage preforms are reheated and stretched against the mold under pneumatic pressure; uneven preform temperature, incorrect blow pressure or timing, or worn mold halves cause containers to come out with thin or uneven wall sections, deformation, haze, flash lines or incomplete forming. These out-of-specification bottles are separated from the good output as first-pass defects rather than reworked inline.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseMES/SCADA shows an elevated reject or scrap counter at the blow molder or downstream inspection station while the machine remains in running state, often correlated with blow pressure, oven temperature or mold cooling parameters drifting outside their normal band. No corresponding unplanned stop is recorded, confirming the loss is a quality rather than an availability event.
Gegenmaßnahme
Ingenieurpraktische HinweiseCalibrate and periodically verify the preform heating profile, blow pressure staging and mold cooling circuits, and perform preventive maintenance and inspection of mold halves and valves to prevent wear-related defects. Implement statistical monitoring of wall-thickness and visual inspection results to detect drift before it generates sustained defect rates.
4Quellen
- Penerapan Metode Total Productive Maintenance untuk Mereduksi Downtime pada Lini Produksi Botol 1 di PT. Grahamas Intitirta (2020)Quelle öffnenVerlustzeit: 14,8 h · laut Bericht: “defect loss”
Wörtliches Zitat anzeigen
This can reduce Filling 1 downtime from 393.78 hours to 67.62 hours and Blowing 1 from 91.35 hours to 14.75 hours.
- Mittlere Ereignisdauer: 85,0 min · laut Bericht: “Setup time”
Wörtliches Zitat anzeigen
Blowing machine Filling machine Labelling machine (bottleneck resource) Packaging machine 85 minutes 69 minutes 148 minutes 97 minutes 57 minutes 73 minutes 0 minutes 51 minutes
- Mittlere Ereignisdauer: 57,0 min · laut Bericht: “Idle time”
Wörtliches Zitat anzeigen
Blowing machine Filling machine Labelling machine (bottleneck resource) Packaging machine 85 minutes 69 minutes 148 minutes 97 minutes 57 minutes 73 minutes 0 minutes 51 minutes
- Analisis Total Productive Maintenance (TPM) dengan Menggunakan Metode Overall Equipment Effectiveness (OEE) pada Mesin Blowing (2025)Quelle öffnenAnteil an der Verlustzeit: 0,210 % · laut Bericht: “Product Defect Losses”
Wörtliches Zitat anzeigen
Rata - rata 6,10 0,95 11,47 0,00 0,00 0,21
- Fehlerquote: 88,0 % · laut Bericht: “Proses Blowing”
Wörtliches Zitat anzeigen
Proses Blowing 310042 88% 88%
- Anzahl der Ereignisse: 310.042 units · laut Bericht: “Proses Blowing”
Wörtliches Zitat anzeigen
Proses Blowing | 310042 | 88% | 88%
- Anteil an den Verlustereignissen: 88,0 % · laut Bericht: “Proses Blowing”
Wörtliches Zitat anzeigen
Proses Blowing | 310042 | 88% | 88%

