Labeling machine changeover and setup
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 2 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 56 % der Verlustzeit der Linie. Berichtet von 8 der 85 Studien, die sie beobachten konnten (gute Evidenz).
Was passiert
Switching product, bottle shape or label format on the labeling machine requires mechanical adjustments such as changing label reels, resetting guide rails and star wheels, and recalibrating sensors and print/apply heads before stable operation is reached. Part of this work is done as internal setup with the line fully stopped, while other tasks could be performed externally while the previous run is still producing, so poor preparation extends the stoppage. The resulting dead time between the last good unit of the previous run and the first good unit of the new run is recorded as changeover loss.
Was man dagegen tut
Apply SMED analysis to separate internal from external setup tasks, pre-staging label reels, tooling and format parts so they are ready before the line stops, and standardizing guide and sensor settings with quick-adjust mechanisms or format recipes stored in the control system. Training operators on a documented changeover sequence and using quick-release fixtures further reduces the internal setup time.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 2,3 % [0,8–5,1 %]
- Erwarteter Anteil an der Verlustzeit
- 1,3 % [0,4–2,9 %]
- Anteil an der Verlustzeit bei Auftreten
- 56 % [45–66 %]
- Studien / Einheiten
- 85 / 113
- Evidenzgrad
- B
Grad B: 5 bis 9 Studien oder eine Intervallbreite zwischen 0,20 und 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte2,4 % [0,4–6,8 %]11 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte3,5 % [1,0–8,3 %]29 Studien
- Bier, Wein und Spirituosen7,1 % [1,8–17,2 %]13 Studien
- Backwaren und Teigwaren2,8 % [0,4–9,0 %]1 Studie
- Fleisch, Geflügel und Fisch2,6 % [0,4–7,7 %]4 Studien
- Obst- und Gemüseverarbeitung2,6 % [0,4–8,3 %]4 Studien
- Getreide- und Ölsaatenmüllerei2,6 % [0,4–8,0 %]3 Studien
- Zucker und Süßwaren2,7 % [0,4–8,4 %]3 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel2,5 % [0,4–8,0 %]4 Studien
- Futtermittel und Heimtiernahrung2,6 % [0,4–7,9 %]4 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)2,4 % [0,4–7,1 %]9 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseSwitching product, bottle shape or label format on the labeling machine requires mechanical adjustments such as changing label reels, resetting guide rails and star wheels, and recalibrating sensors and print/apply heads before stable operation is reached. Part of this work is done as internal setup with the line fully stopped, while other tasks could be performed externally while the previous run is still producing, so poor preparation extends the stoppage. The resulting dead time between the last good unit of the previous run and the first good unit of the new run is recorded as changeover loss.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseThe labeler machine state switches to setup, changeover or stopped mode for an extended duration between the end-of-batch event of one SKU and the start-of-production event of the next, often correlated with operator login or changeover job logs in the MES. Upstream and downstream conveyor accumulation and starvation states appear around the same window, and minor idle events may cluster immediately after restart while the machine stabilizes.
Gegenmaßnahme
Ingenieurpraktische HinweiseApply SMED analysis to separate internal from external setup tasks, pre-staging label reels, tooling and format parts so they are ready before the line stops, and standardizing guide and sensor settings with quick-adjust mechanisms or format recipes stored in the control system. Training operators on a documented changeover sequence and using quick-release fixtures further reduces the internal setup time.
4Quellen
- Optimizing beverage manufacturing: integrating lean manufacturing and machine learning to enhance efficiency and reduce waste (2025)Quelle öffnenAnzahl der Ereignisse: 8,00 Boxes x 12 · laut Bericht: “Mislabeling”
Wörtliches Zitat anzeigen
Mislabeling Average 15 8
- Optimizing beverage manufacturing: integrating lean manufacturing and machine learning to enhance efficiency and reduce waste (2025)Quelle öffnenAnzahl der Ereignisse: 15,0 Boxes x 12 · laut Bericht: “Mislabeling”
Wörtliches Zitat anzeigen
Mislabeling Average 15 8
- Optimizing beverage manufacturing: integrating lean manufacturing and machine learning to enhance efficiency and reduce waste (2025)Quelle öffnenMittlere Ereignisdauer: 42,0 min · laut Bericht: “Line change time”
Wörtliches Zitat anzeigen
Line change time Average 42 16
- Optimizing beverage manufacturing: integrating lean manufacturing and machine learning to enhance efficiency and reduce waste (2025)Quelle öffnenMittlere Ereignisdauer: 16,0 min · laut Bericht: “Line change time”
Wörtliches Zitat anzeigen
Line change time Average 42 16
- USO DA TROCA RÁPIDA DE FERRAMENTAS – TRF – COMO ESTRATÉGIA DE AUMENTO DE PRODUTIVIDADE EM UMA ROTULADORA DE GARRAFAS PLÁSTICAS (2012)Quelle öffnenVerlustzeit: 2,00 min · laut Bericht: “Adjustment of tulip height”
Wörtliches Zitat anzeigen
Regulagem da altura das tulipas 2
- USO DA TROCA RÁPIDA DE FERRAMENTAS – TRF – COMO ESTRATÉGIA DE AUMENTO DE PRODUTIVIDADE EM UMA ROTULADORA DE GARRAFAS PLÁSTICAS (2012)Quelle öffnenVerlustzeit: 3,00 min · laut Bericht: “Adjustment of gluing units”
Wörtliches Zitat anzeigen
Regulagem dos grupos coladores 3
- USO DA TROCA RÁPIDA DE FERRAMENTAS – TRF – COMO ESTRATÉGIA DE AUMENTO DE PRODUTIVIDADE EM UMA ROTULADORA DE GARRAFAS PLÁSTICAS (2012)Quelle öffnenVerlustzeit: 1,00 min · laut Bericht: “Adjustment of label sensors”
Wörtliches Zitat anzeigen
Regulagem dos sensores dos rótulos 1
- USO DA TROCA RÁPIDA DE FERRAMENTAS – TRF – COMO ESTRATÉGIA DE AUMENTO DE PRODUTIVIDADE EM UMA ROTULADORA DE GARRAFAS PLÁSTICAS (2012)Quelle öffnenVerlustzeit: 1,00 min · laut Bericht: “Adjustment of tulip height”
Wörtliches Zitat anzeigen
Regulagem da altura das tulipas 1
- USO DA TROCA RÁPIDA DE FERRAMENTAS – TRF – COMO ESTRATÉGIA DE AUMENTO DE PRODUTIVIDADE EM UMA ROTULADORA DE GARRAFAS PLÁSTICAS (2012)Quelle öffnenVerlustzeit: 3,00 min · laut Bericht: “Adjustment of gluing units”
Wörtliches Zitat anzeigen
Regulagem dos grupos coladores 3
- USO DA TROCA RÁPIDA DE FERRAMENTAS – TRF – COMO ESTRATÉGIA DE AUMENTO DE PRODUTIVIDADE EM UMA ROTULADORA DE GARRAFAS PLÁSTICAS (2012)Quelle öffnenVerlustzeit: 1,00 min · laut Bericht: “Adjustment of label sensors”
Wörtliches Zitat anzeigen
Regulagem dos sensores dos rótulos 1
- Redução de tempos de setup: aplicação de troca rápida de ferramentas em indústria de bebidas (2015)Quelle öffnenVerlustzeit: 31,1 min:s · laut Bericht: “external setup”
Wörtliches Zitat anzeigen
Verificação da rotulagem 00:10 TOTAL 16:34 31:06
- Study on Preventive Maintenance Strategies of Filling Equipment Based on Reliability-Cantered Maintenance (2021)Quelle öffnenVerlustzeit: 450 min · laut Bericht: “LM”
Wörtliches Zitat anzeigen
Total 2540 485 500 560 450 265 225 240 220 5485 224940 2.44%
- Study on Preventive Maintenance Strategies of Filling Equipment Based on Reliability-Cantered Maintenance (2021)Quelle öffnenAnzahl der Ereignisse: 17,0 events · laut Bericht: “LM”
Wörtliches Zitat anzeigen
Total 61 21 24 22 17 7 11 10 8 181
- Mittlere Ereignisdauer: 148 min · laut Bericht: “Setup time”
Wörtliches Zitat anzeigen
Blowing machine Filling machine Labelling machine (bottleneck resource) Packaging machine 85 minutes 69 minutes 148 minutes 97 minutes 57 minutes 73 minutes 0 minutes 51 minutes
- Mittlere Ereignisdauer: 0 min · laut Bericht: “Idle time”
Wörtliches Zitat anzeigen
Blowing machine Filling machine Labelling machine (bottleneck resource) Packaging machine 85 minutes 69 minutes 148 minutes 97 minutes 57 minutes 73 minutes 0 minutes 51 minutes
- Mittlere Ereignisdauer: 148 min · laut Bericht: “equipment setup”
Wörtliches Zitat anzeigen
In short, our results showed that before the method made its mark, the equipment setup averaged 148 minutes, and after the implementation, the setup time decreased to two digits, approximately 19 minutes (Fig. 4).
- Mittlere Ereignisdauer: 19,0 min · laut Bericht: “equipment setup”
Wörtliches Zitat anzeigen
In short, our results showed that before the method made its mark, the equipment setup averaged 148 minutes, and after the implementation, the setup time decreased to two digits, approximately 19 minutes (Fig. 4).
- Optimizing Beverage Manufacturing: Integrating Lean Manufacturing and Machine Learning to Enhance Efficiency and Reduce Waste (2024)Quelle öffnenFehlerquote: 25,0 % · laut Bericht: “incorrectly labeled bottles”
Wörtliches Zitat anzeigen
The main issues concerning the product process include 25% of incorrectly labeled bottles, 18% of improperly sealed bottles, and 12% of reprocessing in the current alcoholic beverage production process.
- Enhancing Productivity through Quick Changeovers: A SMED-Based Methodology in Manufacturing Industry (2026)Quelle öffnenVerlustzeit: 900 s · laut Bericht: “Bottle labeling (per bag)”
Wörtliches Zitat anzeigen
3 Bottle labeling (per bag) 900 - 900
- Enhancing Productivity through Quick Changeovers: A SMED-Based Methodology in Manufacturing Industry (2026)Quelle öffnenVerlustzeit: 600 s · laut Bericht: “Bottle labeling (per bag)”
Wörtliches Zitat anzeigen
2 Bottle labeling (per bag) 600 - 600

