foratvise
Loslegen
Anlagenausfall (Störungen)

Mechanical, electrical or pneumatic component failure

Anlagenausfall (Störungen)VerfügbarkeitGesamte Linie oder nicht spezifizierte Anlage

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 59 % der Verlustzeit der Linie. Berichtet von 5 der 127 Studien, die sie beobachten konnten (gute Evidenz).

Was passiert

Wear, fatigue, misalignment, corrosion or electrical/pneumatic component degradation accumulates in drives, bearings, actuators, sensors, valves, wiring or control hardware until the part can no longer perform its function, forcing the line or a machine to stop until repaired. Because the failing component is not specified, the loss aggregates any breakdown of mechanical, electrical or pneumatic nature across the line rather than a single identifiable failure mode.

Was man dagegen tut

Apply condition-based and preventive maintenance with vibration, current and pressure monitoring on critical mechanical, electrical and pneumatic assets, keep critical spares available, and use root-cause/failure-mode analysis on recurring breakdowns to redesign weak components or revise maintenance intervals.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
1,4 % [0,5–3,2 %]
Erwarteter Anteil an der Verlustzeit
0,9 % [0,3–1,9 %]
Anteil an der Verlustzeit bei Auftreten
59 % [49–69 %]
Studien / Einheiten
127 / 161
Evidenzgrad
B

Grad B: 5 bis 9 Studien oder eine Intervallbreite zwischen 0,20 und 0,35.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    1,5 % [0,2–4,9 %]13 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    1,7 % [0,4–4,8 %]26 Studien
  • Bier, Wein und Spirituosen
    1,5 % [0,2–4,9 %]11 Studien
  • Backwaren und Teigwaren
    3,1 % [0,7–8,3 %]24 Studien
  • Fleisch, Geflügel und Fisch
    1,5 % [0,2–4,7 %]9 Studien
  • Obst- und Gemüseverarbeitung
    1,6 % [0,2–5,2 %]7 Studien
  • Getreide- und Ölsaatenmüllerei
    2,4 % [0,4–7,7 %]6 Studien
  • Zucker und Süßwaren
    1,5 % [0,2–5,0 %]9 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    1,6 % [0,3–4,9 %]5 Studien
  • Futtermittel und Heimtiernahrung
    1,6 % [0,2–5,2 %]7 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    1,6 % [0,2–4,8 %]10 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

Wear, fatigue, misalignment, corrosion or electrical/pneumatic component degradation accumulates in drives, bearings, actuators, sensors, valves, wiring or control hardware until the part can no longer perform its function, forcing the line or a machine to stop until repaired. Because the failing component is not specified, the loss aggregates any breakdown of mechanical, electrical or pneumatic nature across the line rather than a single identifiable failure mode.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

SCADA/MES logs show unplanned machine-down states with maintenance-coded stop reasons, fault or alarm codes from drives, motors, PLC I/O or pneumatic pressure switches, and a sudden drop to zero in actual speed or output counters that persists until a maintenance intervention is logged. Repeated short-interval alarms from the same tag before the final stop can indicate progressive degradation.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Apply condition-based and preventive maintenance with vibration, current and pressure monitoring on critical mechanical, electrical and pneumatic assets, keep critical spares available, and use root-cause/failure-mode analysis on recurring breakdowns to redesign weak components or revise maintenance intervals.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Anteil an der Verlustzeit: 30,2 % · laut Bericht: “mechanical and electrical failures”
    Wörtliches Zitat anzeigen
    These reasons were linked to specific root causes: mechanical and electrical failures explained 30.2% of the stoppages, while instrumentation faults represented 19%.
  2. Anteil an der geplanten Zeit: 7,65 % · laut Bericht: “recurrent failures in mechanical and pneumatic components”
    Wörtliches Zitat anzeigen
    High downtime rate due to recurrent failures in mechanical and pneumatic components 7.65% 1.03% 2.06%
  3. Anteil an der Verlustzeit: 50,0 % · laut Bericht: “equipment mechanical issues”
    Wörtliches Zitat anzeigen
    60% of work time produced results but 30% was lost because materials needed to wait for 40% of the time and 10% stemmed from machine downtime where 50% resulted from equipment mechanical issues.
  4. Verlustzeit: 11.990 min · laut Bericht: “fallas mecánicas, eléctricas y fallas operacionales”
    Wörtliches Zitat anzeigen
    Los motivos principales son las fallas mecánicas, eléctricas, y las fallas operacionales, las cuales generaron 11990 minutos de detención en el año 2024 según se presenta en la tabla 7
  5. Verlustzeit: 7.039 min · laut Bericht: “Falla Mecánica y eléctrica”
    Wörtliches Zitat anzeigen
    Falla Mecánica y eléctrica 7039 24.300% S/336,117.47
  6. Anteil an der Verlustzeit: 24,3 % · laut Bericht: “Falla Mecánica y eléctrica”
    Wörtliches Zitat anzeigen
    Falla Mecánica y eléctrica 7039 24.300% S/336,117.47
  7. Verlustzeit: 1.120 min/year · laut Bericht: “mechanical failures”
    Wörtliches Zitat anzeigen
    16,800 minutes/year lost to changeover times (setup), 1,120 minutes/year due to mechanical failures, 42,336 defective units/year, and 17,472 minutes/year spent searching for tools.
  8. Anzahl der Ereignisse: 7,00 failures/month · laut Bericht: “mechanical failures”
    Wörtliches Zitat anzeigen
    the number of mechanical failures, which averaged 7 per month, was reduced to 1 failure per machine
  9. Anteil an den Verlustereignissen: 50,0 % · laut Bericht: “falha elétrica”
    Wörtliches Zitat anzeigen
    os fatores causadores de perdas com maior impacto na produtividade foram a ocorrência de falha elétrica, seguido da ocorrência de falha mecânica nas máquinas, sendo estes os motivos correspondentes a mais de 50% das ocorrências
  10. Anteil an den Verlustereignissen: 50,0 % · laut Bericht: “falha mecânica”
    Wörtliches Zitat anzeigen
    os fatores causadores de perdas com maior impacto na produtividade foram a ocorrência de falha elétrica, seguido da ocorrência de falha mecânica nas máquinas, sendo estes os motivos correspondentes a mais de 50% das ocorrências