foratvise
Get Started
Equipment failure (breakdowns)

Air compressor failure

Equipment failure (breakdowns)AvailabilityUtilities (steam, compressed air, chilled water, power)

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 131 studies that could observe it (sparse evidence).

What happens

A mechanical, electrical or control fault in the compressed air generation unit (motor, valves, bearings, cooling system or control electronics) causes the compressor to trip or stop, interrupting the supply of compressed air to pneumatic actuators, valves and cylinders across the line. Filling and packaging equipment that depends on pneumatic actuation then loses the pressure needed to operate grippers, valves, pistons and seals.

What is done about it

Implement preventive maintenance on compressors (filter and oil changes, vibration and temperature monitoring, valve inspection) and install redundant compressors or a backup air receiver sized to ride through short outages. Add pressure monitoring with early-warning alarms and automatic switchover to a standby unit to avoid line-wide pneumatic starvation.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.6%]
Expected share of lost time
0.3% [0.1–0.9%]
Share of lost time when present
57% [46–67%]
Studies / units
131 / 165
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.3%]13 studies
  • Soft drinks, bottled water and juices
    0.6% [0.1–2.0%]26 studies
  • Brewing, wine and spirits
    0.9% [0.1–3.4%]12 studies
  • Bakery and pasta
    0.6% [0.1–2.1%]25 studies
  • Meat, poultry and seafood
    0.7% [0.1–2.5%]9 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.4%]7 studies
  • Grain and oilseed milling
    0.7% [0.1–2.5%]7 studies
  • Sugar and confectionery
    0.6% [0.1–2.4%]9 studies
  • Snacks, coffee, tea and other foods
    0.7% [0.1–2.3%]5 studies
  • Animal feed and pet food
    0.7% [0.1–2.5%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.3%]11 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

A mechanical, electrical or control fault in the compressed air generation unit (motor, valves, bearings, cooling system or control electronics) causes the compressor to trip or stop, interrupting the supply of compressed air to pneumatic actuators, valves and cylinders across the line. Filling and packaging equipment that depends on pneumatic actuation then loses the pressure needed to operate grippers, valves, pistons and seals.

How it looks in SCADA data

Engineering guidance

Utility system logs show a drop in compressed air header pressure below setpoint coinciding with a compressor fault or trip alarm and a change in compressor run-state (running to fault/stopped). Downstream machines in filling, capping and packaging simultaneously register low-air alarms, actuator timeout faults or forced stops, with correlated downtime across multiple line assets fed from the same air header.

Countermeasure

Engineering guidance

Implement preventive maintenance on compressors (filter and oil changes, vibration and temperature monitoring, valve inspection) and install redundant compressors or a backup air receiver sized to ride through short outages. Add pressure monitoring with early-warning alarms and automatic switchover to a standby unit to avoid line-wide pneumatic starvation.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Time between events: 41,444 not reported · as reported: “Air Compressor”
    Show verbatim quote
    Waktu Kerusakan Weibull MTTF 41444,25
  2. Mean event duration: 338 not reported · as reported: “Air Compressor”
    Show verbatim quote
    Waktu Perbaikan Lognormal MTTR 337,5107
  3. Share of lost time: 35.0 % · as reported: “air compressor failures”
    Show verbatim quote
    Loss and waste analysis conducted on the beer manufacturing process illustrated in Fig. 1 indicates that more than 35% of the total production downtime is attributed to air compressor failures.