foratvise
Get Started
Process defects (scrap and rework)

Bag Fill Weight and Seal Defects

Process defects (scrap and rework)QualityFilling

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 49 % of the line's lost time. Reported by 1 of the 120 studies that could observe it (sparse evidence).

What happens

Drift or miscalibration in the dosing/weighing system of the bag filling machine causes the filled weight to deviate from the nominal target, while faults in the bag sealing/welding station (incomplete seal, misaligned weld) produce bags that fail integrity checks. Both defect modes occur on the same filling equipment and are detected only after the bag is closed, so the nonconforming unit must be rejected or reworked.

What is done about it

Perform periodic calibration and verification of the filling scale against certified reference weights, and implement closed-loop feedback from the checkweigher to the doser to correct drift automatically. Schedule preventive maintenance and alignment checks on the sealing/welding head, and add an inline seal-integrity test before the bag leaves the filling station.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.6%]
Expected share of lost time
0.3% [0.1–0.8%]
Share of lost time when present
49% [37–62%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.3%]18 studies
  • Soft drinks, bottled water and juices
    0.5% [0.1–1.8%]44 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.2%]16 studies
  • Bakery and pasta
    0.7% [0.1–2.9%]0 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.4%]6 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.4%]4 studies
  • Grain and oilseed milling
    0.7% [0.1–2.5%]6 studies
  • Sugar and confectionery
    0.7% [0.1–2.6%]3 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.2%]6 studies
  • Animal feed and pet food
    0.7% [0.1–2.6%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.9% [0.1–3.4%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Drift or miscalibration in the dosing/weighing system of the bag filling machine causes the filled weight to deviate from the nominal target, while faults in the bag sealing/welding station (incomplete seal, misaligned weld) produce bags that fail integrity checks. Both defect modes occur on the same filling equipment and are detected only after the bag is closed, so the nonconforming unit must be rejected or reworked.

How it looks in SCADA data

Engineering guidance

MES/SCADA logs show checkweigher deviations above or below the nominal setpoint, rising reject counters tagged to the filling machine, and discrete seal/weld fault alarms correlated with the same equipment ID. Trend charts of average fill weight per batch or shift reveal a positive bias, while reject-bin or downgrade counts increase without a corresponding stop in machine-state duration.

Countermeasure

Engineering guidance

Perform periodic calibration and verification of the filling scale against certified reference weights, and implement closed-loop feedback from the checkweigher to the doser to correct drift automatically. Schedule preventive maintenance and alignment checks on the sealing/welding head, and add an inline seal-integrity test before the bag leaves the filling station.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 45.0 % · as reported: “sacarias rejeitadas por peso fora da especificação”
    Show verbatim quote
    sacarias rejeitadas por peso fora da especificação contribuíram com 45%, produtos com peso médio acima do nominal com 20%, e os problemas de soldagem, com 35%.
  2. Share of lost time: 20.0 % · as reported: “produtos com peso médio acima do nominal”
    Show verbatim quote
    sacarias rejeitadas por peso fora da especificação contribuíram com 45%, produtos com peso médio acima do nominal com 20%, e os problemas de soldagem, com 35%.
  3. Share of lost time: 35.0 % · as reported: “problemas de soldagem”
    Show verbatim quote
    sacarias rejeitadas por peso fora da especificação contribuíram com 45%, produtos com peso médio acima do nominal com 20%, e os problemas de soldagem, com 35%.