Bearing failure
In short
It appears in about 2 of every 100 lines studied.
When it appears, it takes on average about 58 % of the line's lost time. Reported by 2 of the 37 studies that could observe it (limited evidence).
What happens
Rotating bearings supporting the bowl, shaft or drive of the separation equipment degrade through fatigue, wear, inadequate lubrication, contamination or misalignment, leading to increased friction, heat generation and eventually seizure or mechanical breakage. Once clearances or surfaces are damaged, vibration and play increase until the equipment can no longer rotate safely and must be stopped for repair.
What is done about it
Apply condition-based maintenance using vibration analysis, temperature monitoring and oil/grease sampling to detect bearing degradation early and replace bearings before catastrophic failure. Ensure correct lubrication schedules, proper alignment and sealing against process contamination during installation and routine maintenance.
Practical guidance written from engineering knowledge; it is not a statistical estimate.
1Probability and evidence
- Probability of presence
- 1.6% [0.3–4.4%]
- Expected share of lost time
- 0.9% [0.2–2.6%]
- Share of lost time when present
- 58% [48–69%]
- Studies / units
- 37 / 44
- Evidence grade
- C
Grade C: 2 to 4 studies, or an interval wider than 0.35.
2Probability by segment
- Dairy products1.8% [0.2–6.5%]5 studies
- Soft drinks, bottled water and juices1.9% [0.2–6.7%]1 study
- Brewing, wine and spirits1.9% [0.2–7.4%]1 study
- Bakery and pasta1.9% [0.2–6.9%]0 studies
- Meat, poultry and seafood1.8% [0.2–6.9%]2 studies
- Fruit and vegetable processing1.7% [0.2–6.0%]3 studies
- Grain and oilseed milling3.8% [0.4–13.7%]6 studies
- Sugar and confectionery1.8% [0.2–6.4%]3 studies
- Snacks, coffee, tea and other foods1.7% [0.2–6.1%]4 studies
- Animal feed and pet food1.7% [0.2–6.1%]5 studies
- Food manufacturing (unspecified or mixed)1.7% [0.2–6.1%]7 studies
3Mechanism, SCADA signature and countermeasure
Mechanism
Engineering guidanceRotating bearings supporting the bowl, shaft or drive of the separation equipment degrade through fatigue, wear, inadequate lubrication, contamination or misalignment, leading to increased friction, heat generation and eventually seizure or mechanical breakage. Once clearances or surfaces are damaged, vibration and play increase until the equipment can no longer rotate safely and must be stopped for repair.
How it looks in SCADA data
Engineering guidanceSCADA/MES data show rising vibration or temperature trends on the drive or bowl bearing points, increasing motor current or torque at constant load, and recurring unplanned stop events tagged to the drive/rotor subsystem with downtime logged for mechanical repair. Alarm history typically shows vibration-high or bearing-temperature-high warnings preceding the final equipment-failure stop.
Countermeasure
Engineering guidanceApply condition-based maintenance using vibration analysis, temperature monitoring and oil/grease sampling to detect bearing degradation early and replace bearings before catastrophic failure. Ensure correct lubrication schedules, proper alignment and sealing against process contamination during installation and routine maintenance.
4Sources
- Riplle Mill Machine Failure Analysis Using the Failure Mode and Effect Analysis (FMEA) Method at PT. Ujong Neubok In (2023)Open sourceTime between events: 3.00 Months · as reported: “Bearing”
Show verbatim quote
Bearing Broken 3 Months
- ANALISIS KERUSAKAN BEARING MAIN SHAFT PADA MESIN SCREW PRESS MSB 15 DENGAN METODE TOTAL PRODUCTIVE MAINTENANCE (TPM) DI PABRIK KELAPA SAWIT PT. XYZ (2024)Open sourceShare of loss events: 24.0 % · as reported: “Human error (Tidak mengikuti SOP) dalam pengoperasian”
Show verbatim quote
Man (manusia) 24% Human error (Tidak mengikuti SOP) dalam pengoperasian
- ANALISIS KERUSAKAN BEARING MAIN SHAFT PADA MESIN SCREW PRESS MSB 15 DENGAN METODE TOTAL PRODUCTIVE MAINTENANCE (TPM) DI PABRIK KELAPA SAWIT PT. XYZ (2024)Open sourceShare of loss events: 39.0 % · as reported: “Engine error (Tidak maksimal)”
Show verbatim quote
Machine (sistem operasi) 39% Engine error (Tidak maksimal)
- ANALISIS KERUSAKAN BEARING MAIN SHAFT PADA MESIN SCREW PRESS MSB 15 DENGAN METODE TOTAL PRODUCTIVE MAINTENANCE (TPM) DI PABRIK KELAPA SAWIT PT. XYZ (2024)Open sourceShare of loss events: 37.0 % · as reported: “Kemasukan besi, kawat dll.”
Show verbatim quote
Materials (bahan baku) 37% Kemasukan besi, kawat dll.

