foratvise
Get Started
Setup and adjustments

Changeover adjustment time to first good unit

Setup and adjustmentsAvailabilityForming, moulding and depositing

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 56 % of the line's lost time. Reported by 0 of the 76 studies that could observe it (sparse evidence).

What happens

After a product or format changeover on the forming station, the mould, mandrel or tooling and the process parameters (temperature, pressure, alignment) must be adjusted and stabilised before the machine can produce a conforming form or product. The time and material consumed between the last good unit of the previous run and the first good form or product of the new run is counted as setup and adjustment loss.

What is done about it

Standardise changeover procedures with predefined set points and tooling positions, use quick-change tooling and automated recipe recall to shorten the adjustment window, and track time and scrap to first good unit as a changeover performance indicator to drive continuous improvement.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.3%]
Expected share of lost time
0.2% [0.0–0.7%]
Share of lost time when present
56% [44–67%]
Studies / units
76 / 96
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.5% [0.0–2.0%]5 studies
  • Soft drinks, bottled water and juices
    0.5% [0.0–1.9%]11 studies
  • Brewing, wine and spirits
    0.5% [0.0–2.0%]0 studies
  • Bakery and pasta
    0.4% [0.0–1.7%]25 studies
  • Meat, poultry and seafood
    0.5% [0.0–1.9%]3 studies
  • Fruit and vegetable processing
    0.5% [0.0–2.0%]3 studies
  • Grain and oilseed milling
    0.5% [0.0–2.0%]0 studies
  • Sugar and confectionery
    0.5% [0.0–1.9%]8 studies
  • Snacks, coffee, tea and other foods
    0.5% [0.0–1.8%]7 studies
  • Animal feed and pet food
    0.5% [0.0–1.9%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.5% [0.0–2.0%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

After a product or format changeover on the forming station, the mould, mandrel or tooling and the process parameters (temperature, pressure, alignment) must be adjusted and stabilised before the machine can produce a conforming form or product. The time and material consumed between the last good unit of the previous run and the first good form or product of the new run is counted as setup and adjustment loss.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows a changeover or setup machine state bounded by the end-of-run event and a quality or counter event tagged as first good part, with repeated micro-adjustments of set points and no stable production counter increment during this interval. Rejected or scrap counts from trial pieces may accumulate before the first good unit flag is raised.

Countermeasure

Engineering guidance

Standardise changeover procedures with predefined set points and tooling positions, use quick-change tooling and automated recipe recall to shorten the adjustment window, and track time and scrap to first good unit as a changeover performance indicator to drive continuous improvement.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Mean event duration: 3.00 min · as reported: “First good form”
    Show verbatim quote
    First good form: 0:03:00
  2. Mean event duration: 27.0 min · as reported: “First good product”
    Show verbatim quote
    First good product: 0:27:00