foratvise
Get Started
Setup and adjustments

CIP cleaning during changeover

Setup and adjustmentsAvailabilityCleaning in place (CIP) and sanitation

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 56 % of the line's lost time. Reported by 0 of the 129 studies that could observe it (sparse evidence).

What happens

Between production runs the line or a section of it must be flushed, washed and sanitized in place (CIP) to remove residues before the next product or batch can start, consuming time that is not available for production. This is a required step of the changeover sequence rather than a failure, and its duration depends on circuit length, soil type and the number of wash/rinse/sanitize stages programmed.

What is done about it

Optimize and standardize the CIP recipe (concentration, temperature, flow and cycle times) for each product/soil combination, use automated recipe selection to avoid over-cleaning, and where feasible run CIP on isolated sections in parallel with changeover tasks on other parts of the line to shorten the critical path.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.3% [0.1–1.0%]
Expected share of lost time
0.2% [0.0–0.6%]
Share of lost time when present
56% [44–67%]
Studies / units
129 / 163
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.5%]13 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.3%]27 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.5%]11 studies
  • Bakery and pasta
    0.4% [0.0–1.4%]24 studies
  • Meat, poultry and seafood
    0.4% [0.0–1.5%]9 studies
  • Fruit and vegetable processing
    0.4% [0.0–1.6%]7 studies
  • Grain and oilseed milling
    0.4% [0.0–1.5%]6 studies
  • Sugar and confectionery
    0.4% [0.0–1.5%]9 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.5%]5 studies
  • Animal feed and pet food
    0.4% [0.0–1.5%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.4%]11 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Between production runs the line or a section of it must be flushed, washed and sanitized in place (CIP) to remove residues before the next product or batch can start, consuming time that is not available for production. This is a required step of the changeover sequence rather than a failure, and its duration depends on circuit length, soil type and the number of wash/rinse/sanitize stages programmed.

How it looks in SCADA data

Engineering guidance

MES/SCADA shows the line or affected equipment in a dedicated CIP or cleaning state with no production counts, often preceded by an end-of-run or product-change trigger and followed by a warm-up or first-good-unit event. Flow, temperature and conductivity trends on the CIP skid confirm the wash/rinse/sanitize phases while downstream stations register starvation.

Countermeasure

Engineering guidance

Optimize and standardize the CIP recipe (concentration, temperature, flow and cycle times) for each product/soil combination, use automated recipe selection to avoid over-cleaning, and where feasible run CIP on isolated sections in parallel with changeover tasks on other parts of the line to shorten the critical path.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 28.0 % · as reported: “CIP line washing”
    Show verbatim quote
    CIP line washing method allowed the company to save around 28 percent of the time and costs used for line washing.