foratvise
Get Started
Equipment failure (breakdowns)

Conveyor drive motor burnout or mechanical failure

Equipment failure (breakdowns)AvailabilityConveying and accumulation

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 1 of the 86 studies that could observe it (sparse evidence).

What happens

The conveyor drive motor overheats and burns its windings, or suffers mechanical failure of bearings, shaft or gearbox, usually due to sustained overload, jammed belt, lack of lubrication or electrical insulation degradation. Loss of torque or motor function stops the conveyor and interrupts material flow along the line.

What is done about it

Apply condition-based maintenance with vibration and thermal monitoring of the drive motor, verify correct motor sizing and overload protection settings, and keep lubrication and alignment within specification. Clear belt jams promptly and install mechanical or electronic overload protection that trips before windings overheat.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.7% [0.1–1.8%]
Expected share of lost time
0.4% [0.1–1.1%]
Share of lost time when present
58% [47–68%]
Studies / units
86 / 112
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.7% [0.1–2.7%]11 studies
  • Soft drinks, bottled water and juices
    0.9% [0.1–3.0%]28 studies
  • Brewing, wine and spirits
    0.7% [0.1–2.8%]12 studies
  • Bakery and pasta
    0.8% [0.1–3.1%]0 studies
  • Meat, poultry and seafood
    0.8% [0.1–2.9%]5 studies
  • Fruit and vegetable processing
    0.8% [0.1–2.8%]4 studies
  • Grain and oilseed milling
    0.8% [0.1–3.0%]4 studies
  • Sugar and confectionery
    0.8% [0.1–2.9%]4 studies
  • Snacks, coffee, tea and other foods
    0.8% [0.1–2.7%]4 studies
  • Animal feed and pet food
    0.8% [0.1–3.0%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.7% [0.1–2.7%]9 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The conveyor drive motor overheats and burns its windings, or suffers mechanical failure of bearings, shaft or gearbox, usually due to sustained overload, jammed belt, lack of lubrication or electrical insulation degradation. Loss of torque or motor function stops the conveyor and interrupts material flow along the line.

How it looks in SCADA data

Engineering guidance

Motor current or torque rises progressively before tripping on overcurrent or thermal overload alarm, followed by a prolonged conveyor stopped state requiring maintenance reset rather than operator clearance. Upstream equipment shows blocking and downstream equipment shows starvation during the stop, and the event log records an electrical or mechanical fault code tied to the drive motor.

Countermeasure

Engineering guidance

Apply condition-based maintenance with vibration and thermal monitoring of the drive motor, verify correct motor sizing and overload protection settings, and keep lubrication and alignment within specification. Clear belt jams promptly and install mechanical or electronic overload protection that trips before windings overheat.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of loss events: 81.0 % · as reported: “Queima do motor / falhas mecânicas”
    Show verbatim quote
    O tempo de linha parada pela queima do motor, ou falhas mecânicas representava 81% das ocorrências, de acordo com os registros históricos da área de manutenção, sendo assim esta causa foi validada.