Conveying and accumulation
Conveying and accumulation of bottles between the filler and the labeller
In short
Conveying and accumulation can use at most 100 of every 100 planned hours. The rest goes to limits no plant can avoid.
- 100usable at most
The three limits that set it
Running time: up to 100 %
The rest are stops imposed by physics or by regulation: cleaning, changeovers, defrosting.
Speed: up to 100 %
How close to its maximum speed it can run without damaging the product or the equipment.
Good product: up to 100 %
Some product falls outside specification even with the process well under control.
Technical detail
Uncertainty intervals, physical models per station and sources, for anyone who wants to check each figure.
1Scenario
In a carbonated soft drink bottling line, filled and capped 0.5 L PET bottles leave the filler on lubricated plastic-chain conveyors, cross an accumulation table and are fed in single file to the labeller. The filler is the slowest machine of the line and the labeller runs faster (the V-graph of a bottling line). The accumulation table is the buffer: while the labeller is down, the filler keeps running into it; when the labeller restarts, its speed surplus empties it. Machine rates and the measured failure behaviour of the labeller are those of an industrial bottling plant; the conveyor geometry, the bottle and the conveyor speed are declared scenario values. The model bounds what physics allows the conveyor to do (stable transport, buffer capacity) and quantifies how much of the labeller's stopping time reaches the filler through a buffer of given size.
2Results
- Largest acceleration that base friction can give a free-standing container (mu g)1.27 [0.75–1.81] m/s²
- Inertial acceleration at which a container would tip (g D / 2h)3.54 [3.13–4.03] m/s²
- Tipping limit over friction coefficient, D / (2 h mu): above 1 the container slides before it tips2.78 [1.91–4.86]
- Share of containers that tip at the declared number of speed transfers (local friction above the tipping limit)2.66 × 10⁻¹⁴ [NaN × 10⁻Infinity–1.48 × 10⁻⁴]
- TheoreticalMaximum OEE quality factor (containers that stay upright)1.00000 [0.99985–1.00000]
- Conveyor speed needed to feed the labeller in single file with touching containers0.599 [0.573–0.626] m/s
- Shortest time in which friction brings a container from rest to the single-file speed0.470 [0.330–0.803] s
- Containers held by the accumulation table at densest (hexagonal) packing1,640 [771–3,813]
- Time the full buffer keeps the filler running while the labeller is down204 [96–473] s
- Time the labeller needs to empty a full buffer with its speed surplus (V-graph)1,406 [661–3,269] s
- Mean number of containers in the buffer80.0 [53.6–86.4]
- Share of time the filler is blocked by labeller stops that the buffer cannot absorb3.66 × 10⁻⁴ [1.59 × 10⁻⁶–3.30 × 10⁻³]
- Blocking with the buffer over blocking without any buffer0.0134 [0.0001–0.1206]
- TheoreticalThermodynamic minimum energy of horizontal transport0 kJ/kg
- TypicalFriction dissipated by the belt sliding under accumulated containers, per kg of product (declared buffer and speed)0.0127 [0.0069–0.0242] kJ/kg
- TheoreticalMaximum yield (conveying consumes no product)1.00
- TheoreticalMaximum availability (no conveyor stop is forced by physics or regulation)1.00
- Filler availability against labeller stops without a buffer (documented labeller MTBF and MTTR)0.973
- Filler availability against labeller stops propagated through the declared buffer0.9996 [0.9967–1.0000]
- TheoreticalPerformance factor (the conveyor carries the line rate with a speed surplus)1.00
- TheoreticalPhysics-bounded OEE1.00000 [0.99985–1.00000]
- OEE with the documented labeller stops propagated through the declared buffer0.9996 [0.9966–1.0000]
3Ceilings per dimension
- Theoretical
- Best available technique
- Best documented
- Typical
- TheoreticalMaximum OEE quality factor (containers that stay upright)1.00000 [0.99985–1.00000]
- TheoreticalThermodynamic minimum energy of horizontal transport0 kJ/kg
- TypicalFriction dissipated by the belt sliding under accumulated containers, per kg of product (declared buffer and speed)0.0127 [0.0069–0.0242] kJ/kg
- TheoreticalMaximum yield (conveying consumes no product)1.00
- TheoreticalMaximum availability (no conveyor stop is forced by physics or regulation)1.00
- TheoreticalPerformance factor (the conveyor carries the line rate with a speed surplus)1.00
- TheoreticalPhysics-bounded OEE1.00000 [0.99985–1.00000]
4Loss cascade
- TheoreticalTypicalEnergy per unit of product0 kJ/kg → 0.0127 [0.0069–0.0242] kJ/kg (gap 0.0127 kJ/kg)
Horizontal transport lifts nothing and changes nothing in the container, so its thermodynamic minimum is zero. Energy is dissipated wherever the belt slides under a bottle that is held back: on an accumulation table the chain keeps running under every stationary bottle and dissipates mu m g v per bottle, which with the mean buffer level of the scenario is still a small fraction of a joule per kilogram of product. The electricity of a real conveyor line is dominated by chain friction on the wear strips, gearmotor losses and the conveyors that run empty or under a full table for long periods; lubrication lowers the friction term but too little friction lets bottles tip and fall.
5Physics-bounded OEE
- Loading time (ideal)1.000
- Availabilityfactor 1.001.000 (−0.000)
- Performancefactor 1.001.000 (−0.000)
- Qualityfactor 1.00000 [0.99985–1.00000]1.000 (−0.000)
- Physics-bounded OEE1.00000 [0.99985–1.00000]
6Full derivation
Scope. In a carbonated soft drink bottling line, filled and capped 0.5 L PET bottles leave the filler on lubricated plastic-chain conveyors, cross an accumulation table and are fed in single file to the labeller. The filler is the slowest machine and the labeller runs faster (the V-graph of a bottling line). The accumulation table is the buffer that decouples the two machines. Machine rates and the measured failure behaviour of the labeller come from an industrial bottling plant (Bär et al., 2021, Table A1); conveyor geometry, bottle and conveyor speed are declared. Symbols and their values, units, uncertainty distributions and sources are listed in the parameter table generated from config/physics/conveying.yaml. Numbers quoted here are point values; the output table gives the Monte Carlo intervals.
1. Mass balance — maximum yield
Conveying neither creates nor consumes product: every bottle that enters leaves, so . A bottle that tips and falls is a nonconforming unit (section 4), not a mass loss of conforming product.
2. Energy balance — minimum energy per kg
Horizontal transport lifts nothing and changes nothing in the bottle: its final state equals its initial state, so the thermodynamic minimum is zero. Energy is dissipated wherever the belt slides under a bottle that is held back. On an accumulation table the chain keeps running under every stationary bottle and dissipates the friction power per bottle, where is the coefficient of friction, the mass of the full bottle, the gravity acceleration and the belt speed. With the mean buffer level of section 5 and the filler output , the dissipation per kg of product is
It is small because the buffer is nearly empty most of the time (80 bottles on average). The electricity of a real conveyor line is dominated by chain friction on the wear strips, gearmotor losses and conveyors that run empty or under a full table for long periods.
3. Rate-limiting step — single-file speed and stable acceleration
Single-file speed. To feed the labeller with touching bottles of diameter the conveyor must run at least at
with = 33 197 bottles per hour, the measured set performance of the labeller. Conveyors run faster than this, so they do not set the cycle of the line: .
Stable acceleration. A free-standing bottle is accelerated only by the friction at its base, so its acceleration cannot exceed
with = 0.13, the coefficient of friction measured for bottles on a conveyor track with a dry lubricant (US 9 562 209 B2). The shortest time to bring a bottle from rest to the single-file speed is = 0.47 s: a belt that accelerates faster only slides under the bottles.
4. Process capability — quality ceiling (stability)
A bottle of base diameter whose centre of gravity is at height is a rigid body. When the belt accelerates under it, the friction force acts at the base and the inertial force at the centre of gravity; the bottle tips about its base edge when the overturning moment exceeds the restoring moment of its weight, i.e. when
The corresponding inertial acceleration is = 3.54 m/s². Because friction limits the acceleration to , a bottle slides before it can tip whenever ; the stability margin is
The lubricant documents keep friction at a proper value rather than the minimum, because for bottles an unacceptably low coefficient of friction "may result in an excessive number of tipped and fallen bottles" (US 7 745 381 B2). In this model low friction can never tip a free bottle, so that mechanism must come from contact forces the model leaves out (guide rails, curves, pushing neighbours). In the model, tipping can occur only where the local friction is high (a dry spot, a spill of sugar syrup). With the local friction scattered as and speed transfers between filler and labeller,
with the standard normal distribution function. For a full bottle on a lubricated track the stability ceiling does not limit quality; it would for empty PET bottles (high centre of gravity) or high-friction tracks, which are outside the validity of the model.
5. Buffer theory — what accumulation does for the line
Buffer capacity. The densest arrangement of equal circles in a plane is the hexagonal packing, which covers = 90.7 % of the area. A table of length and width therefore holds at most
( = 10 m, = 0.6 m, = 65 mm), an upper bound: edge effects and the single-file lanes reduce it.
Two-stage line with a buffer. The filler (rate = 28 998 per hour while not blocked) feeds the buffer; the labeller empties it at when it runs, where is its speed surplus (the V-graph: 33 197 against 28 998 per hour). The labeller fails at rate and is repaired at rate , with exponential times as in the plant simulation of the source (measured MTBF = 1 423 s, MTTR = 40 s). The filler is the bottleneck and is treated as reliable here: its own stops belong to the filling model and only lower the buffer level, so the blocking computed below is an upper bound. Material is treated as a continuous flow of level .
Let and be the stationary densities of the level while the labeller is up and down, the probability of an empty buffer with the labeller up (the labeller then runs at the filler rate) and the probability of a full buffer with the labeller down (the filler is blocked). While the labeller is down the level rises at ; while it is up it falls at . In the stationary state the probability flux across every level is zero,
and the balance of the up state, , then gives
The boundaries close the solution: the empty atom leaves at the failure rate, , and the full atom is fed by the rising level and left at the repair rate, , so
is the share of time the filler is blocked by labeller stops that outlast the buffer. Two limits check it: without a buffer () , the down-time share of the labeller, i.e. every labeller stop reaches the filler; with (the labeller's surplus drains faster than its stops fill) falls exponentially with . The mean level is . The tests check and against an independent event simulation of the same line.
Scenario values. With the documented rates and failure behaviour, per bottle and . The buffer time (how long a full buffer keeps the filler running) is = 204 s, five times the mean repair time; the time the labeller needs to empty a full buffer with its surplus is = 1 406 s, about one mean time between failures. Then
against = 0.9727 without any buffer: the table absorbs 98.7 % of the labeller's stopping time. The buffer theory states the role of conveying in a line: conveyors are interlinked so that a buffer absorbs the downtime of individual machines, and only when the buffer time is exceeded does the stop propagate (Bär et al., 2021).
6. Unavoidable stops and physics-bounded OEE
No conveyor stop is required by regulation or forced by a physical mechanism, and no cleaning-in-place applies to conveyors, so the cleaning model is not used:
Scope of the bound. The theoretical label of means physics-bounded under the declared scenario. Conveying does not bound the OEE of the line by physics: the conveyor carries the line rate with a speed surplus, and a full bottle on a lubricated track slides before it can tip. What conveying contributes is the buffer. The propagated labeller stops are the labeller's losses seen at the filler, so they enter only availability_scenario (0.99963) and oee_scenario (0.99963).
No double counting. The labeller's own stops are reported by the labelling model (availability_documented); this model reports the share of them that reaches the filler through a buffer of given size. A line calculation must use either the labeller's own downtime (the line without buffers) or the propagated share computed here, never both. In the physics bound, the labelling model forces no stop that a buffer could absorb (its is 1), so the physics-bounded availability of conveying is 1 and the buffer matters only for the declared and documented stops.
7. Assumptions and validity
See the assumption and validity lists generated from the configuration file. The most influential inputs (sensitivity table) are the buffer length and width, the bottle diameter and the documented failure behaviour for the scenario availability, and the friction coefficient and its local scatter for stability.
References
- Bär, R. M., Zeilmann, M., Nophut, C., Kleinert, J., Beyer, K., Voigt, T. (2021). Simulation of energy and media demand of beverage bottling plants by automatic model generation. Sustainability, 13, 10089. doi:10.3390/su131810089
- United States Patent 9 562 209 B2 (2017). Dry lubricant for conveying containers (Ecolab USA Inc.).
- United States Patent 7 745 381 B2 (2010). Lubricant for conveying containers (Ecolab Inc.).
7Parameters and provenance
- 28,998 1/h
Set performance of the filling and closing machine of an industrial bottling plant (measured; the table cell is shared with the empty bottle inspector)
Technology · Fixed
Verified quoteShow verbatim quote
Empty bottle inspector 1 28,998 1 433 68 86.4 0.93 0.005 0.61 0.006 0.61 0.009 0.64 0.075 20.73 0.022 14.84 0.025 14.59 0.038 14.18 0.271 Filling and Closing machine 120Simulation of Energy and Media Demand of Beverage Bottling Plants by Automatic Model Generation (Bär, R. M.; Zeilmann, M.; Nophut, C.; Kleinert, J.; Beyer, K.; Voigt, T.), Sustainability 13, 10089 (2021), CC BY 4.0 (opens in a new tab). MDPI (copy distributed by a co-author's institution), 2021. p. 18. doi:10.3390/su131810089
- 33,197 1/h
Set performance of the labelling machine of the same plant (measured)
Technology · Fixed
Verified quoteShow verbatim quote
Labelling machine 33,197 30 1423 40 97.3Simulation of Energy and Media Demand of Beverage Bottling Plants by Automatic Model Generation (Bär, R. M.; Zeilmann, M.; Nophut, C.; Kleinert, J.; Beyer, K.; Voigt, T.), Sustainability 13, 10089 (2021), CC BY 4.0 (opens in a new tab). MDPI (copy distributed by a co-author's institution), 2021. p. 18. doi:10.3390/su131810089
- 1,423 s
Measured mean time between failures of the labelling machine
Benchmark · Fixed
Verified quoteShow verbatim quote
Labelling machine 33,197 30 1423 40 97.3Simulation of Energy and Media Demand of Beverage Bottling Plants by Automatic Model Generation (Bär, R. M.; Zeilmann, M.; Nophut, C.; Kleinert, J.; Beyer, K.; Voigt, T.), Sustainability 13, 10089 (2021), CC BY 4.0 (opens in a new tab). MDPI (copy distributed by a co-author's institution), 2021. p. 18. doi:10.3390/su131810089
- 40 s
Measured mean time to repair of the labelling machine
Benchmark · Fixed
Verified quoteShow verbatim quote
Labelling machine 33,197 30 1423 40 97.3Simulation of Energy and Media Demand of Beverage Bottling Plants by Automatic Model Generation (Bär, R. M.; Zeilmann, M.; Nophut, C.; Kleinert, J.; Beyer, K.; Voigt, T.), Sustainability 13, 10089 (2021), CC BY 4.0 (opens in a new tab). MDPI (copy distributed by a co-author's institution), 2021. p. 18. doi:10.3390/su131810089
- 0.13
Coefficient of friction between the bottles and the lubricated conveyor track
Property · Triangular 0.06, 0.13, 0.2
Verified quoteShow verbatim quote
The coefficient of friction of the bottles on the track was likewise determined to be 0.09 at 30 minutes after the lubricant spray was applied and 0.13 at 90 minutes after the lubricant spray was applied.US 9 562 209 B2, Dry lubricant for conveying containers (Ecolab USA Inc.), granted 2017-02-07 (opens in a new tab). United States Patent and Trademark Office (full text as published by Google Patents), 2017. US9562209B2
- 0.03
Local scatter of the friction coefficient along the track (dry spots
Scenario · Uniform 0.01 to 0.05
Declared assumptionNo open source quantifies the local scatter; declared assumption.
- 4
Number of speed transfers a bottle crosses between filler and labeller (dead plates, conveyor-to-conveyor and table transfers)
Scenario · Uniform 2 to 8
Declared assumption - 65 mm
Base (standing) diameter of the 0.5 L PET bottle
Scenario · Uniform 62 to 68 mm
Declared assumptionNo open bottle drawing was used; declared assumption.
- 90 mm
Height of the centre of gravity of the full bottle above its base
Scenario · Uniform 80 to 100 mm
Declared assumption - 0.55 kg
Mass of the full bottle
Scenario · Fixed
Declared assumption - 10 m
Length of the accumulation table
Scenario · Uniform 5 to 20 m
Declared assumption - 0.6 m
Width of the accumulation table
Scenario · Uniform 0.4 to 0.8 m
Declared assumption - 1 m/s
Speed of the conveyor belt under the accumulated bottles
Scenario · Uniform 0.8 to 1.5 m/s
Declared assumption
8Benchmarks
| Benchmark | Ceiling | Value | Provenance |
|---|---|---|---|
Availability of the labelling machine itself (97.3 %, measured); it equals the filler availability against labeller stops only when there is no buffer (availability_unbuffered)Show verbatim quoteLabelling machine 33,197 30 1423 40 97.3Simulation of Energy and Media Demand of Beverage Bottling Plants by Automatic Model Generation (Bär, R. M.; Zeilmann, M.; Nophut, C.; Kleinert, J.; Beyer, K.; Voigt, T.), Sustainability 13, 10089 (2021), CC BY 4.0 (opens in a new tab). MDPI (copy distributed by a co-author's institution), 2021. p. 18. doi:10.3390/su131810089 | Best documented | 97.3 % | Verified quote |
9Unavoidable stops
- Labeller stops that outlast the buffer (scenario: availability_scenario only)Verified quote
Conveyors are interlinked so that a buffer absorbs the downtime of a machine; when the buffer time is exceeded the stop propagates to the filler as a tailback. The stops belong to the labeller, not to physics, so they enter only the scenario availability.
Show verbatim quote
The interlinking of the conveyors enables the buffering of downtimes caused, for example, by the failures of individual machines. If the buffer time of the conveyors is exceeded, downtimes lead to failure propagation, which is characterized as a lack or tailback situation.Simulation of Energy and Media Demand of Beverage Bottling Plants by Automatic Model Generation (Bär, R. M.; Zeilmann, M.; Nophut, C.; Kleinert, J.; Beyer, K.; Voigt, T.), Sustainability 13, 10089 (2021), CC BY 4.0 (opens in a new tab). MDPI (copy distributed by a co-author's institution), 2021. p. 4. doi:10.3390/su131810089
10Assumptions
- Bottles are rigid bodies standing on a flat track; the only horizontal force on a free bottle is base friction (Coulomb, coefficient mu). A bottle tips only if the local friction exceeds D / (2h); bottles pushed by neighbours or guide rails are outside the model.
- Buffer capacity is the densest (hexagonal) packing of equal circles on the table area, an upper bound; edge effects and the single-file lanes are neglected.
- Buffer theory: continuous flow; the labeller fails and is repaired with exponential times (as in the source plant simulation); the filler is the bottleneck and is treated as reliable in this two-stage model: its own stops belong to the filling model and only lower the buffer level, so the blocking computed here is an upper bound.
- Availability: no conveyor stop is forced by physics or regulation, so availability_max = 1. The propagated stops of the labeller are the labeller's losses seen at the filler: in a line calculation use either the labeller's own downtime (no buffer) or the propagated share computed here, never both.
- No cleaning-in-place applies to conveyors, so the cleaning model is not used. Performance is 1: the conveyors run faster than the line rate and do not set the cycle.
11Range of validity
- Free-standing rigid or filled containers on horizontal mass and single-file conveyors; empty PET bottles (high centre of gravity, light weight), inclines and air conveyors are outside the model.
- One buffer between a reliable bottleneck and one faster downstream machine with exponential failures; several buffers in series need a decomposition method.
12Sensitivity
- Base (standing) diameter of the 0.5 L PET bottleelasticity 0.000Spearman ρ +0.09
- Height of the centre of gravity of the full bottle above its baseelasticity 0.000Spearman ρ -0.22
- Local scatter of the friction coefficient along the track (dry spotselasticity 0.000Spearman ρ -0.87
- Coefficient of friction between the bottles and the lubricated conveyor trackelasticity 0.000Spearman ρ -0.24
- Output rises with the parameter
- Output falls with the parameter
13Validation checks
- Dimensional analysis22 outputs converted to their declared unitsPassed
- Every cited value verified against its source7 verified, 0 failedPassed
- No documented value beats the theoretical limitPassed
- Ceilings in physical orderPassed
- Fractions within 0 and 1Passed
14Causes of loss in this operation
- Unclassified Loss (Generic OEE Category Label Only)not classifiable1.0% [0.2–2.6%]C86 studies
- Conveyor mechanical fault or jamEquipment failure (breakdowns)0.9% [0.2–2.3%]C86 studies
- Transfer carriage failure at tippler stationEquipment failure (breakdowns)0.7% [0.1–1.9%]D86 studies
- Conveyor line breakdown stoppageEquipment failure (breakdowns)0.7% [0.1–1.9%]D86 studies
- Depalletizer/Unpacker Equipment FailureEquipment failure (breakdowns)0.7% [0.1–1.9%]D86 studies
- Expedition feed conveyor failureEquipment failure (breakdowns)0.7% [0.1–2.0%]D86 studies
- Product leakage/spillage from bulk material conveying equipmentEquipment failure (breakdowns)0.7% [0.1–1.9%]D86 studies
- Discharge conveyor failureEquipment failure (breakdowns)0.7% [0.1–1.9%]D86 studies
- Helical screw conveyor failureEquipment failure (breakdowns)0.7% [0.1–1.8%]D86 studies
- Transportation time between stationsnot classifiable0.7% [0.1–1.9%]D86 studies
- Conveyor drive motor burnout or mechanical failureEquipment failure (breakdowns)0.7% [0.1–1.8%]D86 studies
- Metal conveyor chain/track failureEquipment failure (breakdowns)0.7% [0.1–1.8%]D86 studies
- Conveyor cleaning during changeoverSetup and adjustments0.6% [0.1–1.7%]D86 studies
- Conveyor belt misalignment / tracking faultEquipment failure (breakdowns)0.4% [0.1–1.4%]D86 studies
- Conveyor roller fouling from dirt buildupEquipment failure (breakdowns)0.4% [0.1–1.4%]D86 studies
- Rotary conveyor dry-run failureEquipment failure (breakdowns)0.4% [0.1–1.3%]D86 studies
- Product jam/blockage on infeed conveyorIdling and minor stops (micro-stops)0.4% [0.1–1.2%]D86 studies
15References
- Simulation of Energy and Media Demand of Beverage Bottling Plants by Automatic Model Generation (Bär, R. M.; Zeilmann, M.; Nophut, C.; Kleinert, J.; Beyer, K.; Voigt, T.), Sustainability 13, 10089 (2021), CC BY 4.0 (opens in a new tab). MDPI (copy distributed by a co-author's institution), 2021. p. 18. doi:10.3390/su131810089
- US 9 562 209 B2, Dry lubricant for conveying containers (Ecolab USA Inc.), granted 2017-02-07 (opens in a new tab). United States Patent and Trademark Office (full text as published by Google Patents), 2017. US9562209B2
- us7745381b2_lubricant
- doi:10.3390/su131810089 — Bottling-plant simulation with measured set performances, MTBF and MTTR of every machine (Table A1).

