foratvise
Get Started
Process defects (scrap and rework)

Cut piece dimension/weight out of customer specification limits

Process defects (scrap and rework)QualityCutting, slicing and deboning

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 3 of the 39 studies that could observe it (sparse evidence).

What happens

Process variability in the cutting or portioning step, such as blade wear, inconsistent actuator positioning, or raw material size variation, makes the resulting piece dimension or weight drift away from the target. When the process mean shifts or the distribution becomes skewed, an increasing share of pieces falls beyond the upper or lower specification limit set by a given customer.

What is done about it

Apply statistical process control with corrective adjustment rules to recenter the cutting or portioning process before drift reaches the specification limits, including routine blade maintenance and actuator calibration. Segregate or pre-sort incoming raw material by size when feedstock variability is the dominant driver, and review customer-specific tolerance windows against actual process capability.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.9% [0.2–2.9%]
Expected share of lost time
0.5% [0.1–1.4%]
Share of lost time when present
48% [36–60%]
Studies / units
39 / 48
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.1% [0.1–4.2%]5 studies
  • Soft drinks, bottled water and juices
    1.1% [0.1–4.5%]1 study
  • Brewing, wine and spirits
    1.1% [0.1–4.6%]0 studies
  • Bakery and pasta
    1.1% [0.1–4.5%]0 studies
  • Meat, poultry and seafood
    1.6% [0.2–5.9%]5 studies
  • Fruit and vegetable processing
    1.1% [0.1–4.0%]6 studies
  • Grain and oilseed milling
    1.1% [0.1–4.4%]3 studies
  • Sugar and confectionery
    1.1% [0.1–4.4%]3 studies
  • Snacks, coffee, tea and other foods
    1.1% [0.1–4.7%]3 studies
  • Animal feed and pet food
    1.1% [0.1–4.2%]5 studies
  • Food manufacturing (unspecified or mixed)
    1.1% [0.1–3.9%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Process variability in the cutting or portioning step, such as blade wear, inconsistent actuator positioning, or raw material size variation, makes the resulting piece dimension or weight drift away from the target. When the process mean shifts or the distribution becomes skewed, an increasing share of pieces falls beyond the upper or lower specification limit set by a given customer.

How it looks in SCADA data

Engineering guidance

Statistical process control charts on the cutting line show the measured dimension or weight distribution shifting or becoming skewed toward one specification limit, with growing counts of individual points beyond USL or LSL for a specific customer product. Downstream checkweigher or inspection stations log corresponding rises in reject or hold counts tied to that product code.

Countermeasure

Engineering guidance

Apply statistical process control with corrective adjustment rules to recenter the cutting or portioning process before drift reaches the specification limits, including routine blade maintenance and actuator calibration. Segregate or pre-sort incoming raw material by size when feedstock variability is the dominant driver, and review customer-specific tolerance windows against actual process capability.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Defect rate: 88.0 % · as reported: “Customer D non-conforming at LSL”
    Show verbatim quote
    D | non-conforming at the lower specification limit at 84 and 88%, respectively
  2. Defect rate: 84.0 % · as reported: “Customer C non-conforming at LSL”
    Show verbatim quote
    C | non-conforming at the lower specification limit at 84 and 88%, respectively
  3. Defect rate: 100 % · as reported: “Customer C non-conforming below LSL”
    Show verbatim quote
    C | 100% non-conforming, where the results fell largely below the lower specification limit. No over-trimming
  4. Defect rate: 20.0 % · as reported: “Customer C non-conforming, left skewed toward LSL”
    Show verbatim quote
    C | 20% were non-conforming within the specifications left skewed of the target (i.e. the non-conforming longissimus dorsi were found towards the lower limit (LSL)
  5. Defect rate: 20.0 % · as reported: “Customer E outside specification”
    Show verbatim quote
    E | 20% outside specifications
  6. Defect rate: 16.0 % · as reported: “Customer A non-conforming at USL”
    Show verbatim quote
    Outlier observed A customer specification – however, it was the most conforming specification, with only 16% non-conforming in the USL
  7. Defect rate: 100 % · as reported: “Customer A outliers non-conforming”
    Show verbatim quote
    A | Outliers - 100% non-conforming with the specification requirements
  8. Defect rate: 20.0 % · as reported: “Customer E non-conforming, right skewed toward USL”
    Show verbatim quote
    E | 20% were non-conforming within the specifications -Right skewed of the target (i.e. that non-conforming were found towards the upper specification limit (USL))