foratvise
Get Started
Reduced speed

Fouled/dirty forming dies

Reduced speedPerformanceForming, moulding and depositing

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 64 % of the line's lost time. Reported by 1 of the 76 studies that could observe it (sparse evidence).

What happens

Product residue, grease or process debris gradually accumulates on the working surfaces of the forming dies, altering material flow, release and dimensional accuracy. To avoid defects or jamming, operators deliberately run the forming station below its design rate until the dies are cleaned.

What is done about it

Implement a scheduled die cleaning or wipe-down routine based on run time or visual/sensor inspection, and consider improved release coatings or automated in-process cleaning cycles to limit residue buildup.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.9% [0.2–2.4%]
Expected share of lost time
0.6% [0.1–1.6%]
Share of lost time when present
64% [51–76%]
Studies / units
76 / 96
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.0% [0.1–3.9%]5 studies
  • Soft drinks, bottled water and juices
    0.9% [0.1–3.2%]11 studies
  • Brewing, wine and spirits
    1.1% [0.1–4.2%]0 studies
  • Bakery and pasta
    0.9% [0.1–3.0%]25 studies
  • Meat, poultry and seafood
    1.1% [0.1–4.1%]3 studies
  • Fruit and vegetable processing
    1.0% [0.1–4.2%]3 studies
  • Grain and oilseed milling
    1.1% [0.1–4.1%]0 studies
  • Sugar and confectionery
    1.0% [0.1–3.6%]8 studies
  • Snacks, coffee, tea and other foods
    1.4% [0.2–5.2%]7 studies
  • Animal feed and pet food
    1.0% [0.1–3.6%]6 studies
  • Food manufacturing (unspecified or mixed)
    1.0% [0.1–3.6%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Product residue, grease or process debris gradually accumulates on the working surfaces of the forming dies, altering material flow, release and dimensional accuracy. To avoid defects or jamming, operators deliberately run the forming station below its design rate until the dies are cleaned.

How it looks in SCADA data

Engineering guidance

MES/SCADA shows the forming station running continuously but at a cycle rate persistently below the ideal set point, with no fault or stop alarms raised; the slow period typically ends with a short cleaning or maintenance state before speed returns to normal. Trend data often shows a gradual decline in rate between cleaning events, correlating with run time since the last die cleaning.

Countermeasure

Engineering guidance

Implement a scheduled die cleaning or wipe-down routine based on run time or visual/sensor inspection, and consider improved release coatings or automated in-process cleaning cycles to limit residue buildup.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of planned time: 14.4 % · as reported: “dies kotor”
    Show verbatim quote
    nilai six big losses tertinggi pada faktor reduced speed losses yaitu 14,37%
  2. Share of planned time: 5.48 % · as reported: “dies kotor”
    Show verbatim quote
    nilai reduced losses yang memiliki kontribusi terbesar terhadap rendahnya nilai six big losses yang sebelumnya 14.37% menjadi 5.48%