foratvise
Get Started
Process defects (scrap and rework)

Dosing inaccuracy in forming/pelletizing

Process defects (scrap and rework)QualityForming, moulding and depositing

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 47 % of the line's lost time. Reported by 0 of the 76 studies that could observe it (sparse evidence).

What happens

The metering or feeding system that delivers raw material to the pelletizing/forming unit drifts from its set point because of wear, calibration error, material flow variability or control loop instability, so the mass or volume fed per cycle deviates from the target. This produces pellets or formed units with incorrect weight, density or dimensions even though the line is running under otherwise stable conditions.

What is done about it

Recalibrate and periodically verify the dosing/feeding mechanism against reference weights or flow standards, and tighten the control loop tuning or add closed-loop weight feedback to the feeder. Implement preventive maintenance on wear-prone metering components and set tighter in-process tolerance alarms so drift is caught before it generates nonconforming product.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.4%]
Expected share of lost time
0.2% [0.0–0.6%]
Share of lost time when present
47% [35–58%]
Studies / units
76 / 96
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.5% [0.0–2.0%]5 studies
  • Soft drinks, bottled water and juices
    0.5% [0.0–2.0%]11 studies
  • Brewing, wine and spirits
    0.5% [0.0–2.2%]0 studies
  • Bakery and pasta
    0.5% [0.0–1.8%]25 studies
  • Meat, poultry and seafood
    0.5% [0.0–2.3%]3 studies
  • Fruit and vegetable processing
    0.5% [0.0–2.1%]3 studies
  • Grain and oilseed milling
    0.6% [0.0–2.3%]0 studies
  • Sugar and confectionery
    0.5% [0.0–2.1%]8 studies
  • Snacks, coffee, tea and other foods
    0.5% [0.0–1.9%]7 studies
  • Animal feed and pet food
    0.5% [0.0–2.2%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.5% [0.0–2.2%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The metering or feeding system that delivers raw material to the pelletizing/forming unit drifts from its set point because of wear, calibration error, material flow variability or control loop instability, so the mass or volume fed per cycle deviates from the target. This produces pellets or formed units with incorrect weight, density or dimensions even though the line is running under otherwise stable conditions.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows the dosing or feeder actuator signal (screw speed, valve opening, belt feeder rate) oscillating or drifting away from the recipe set point while the machine remains in run state, together with increasing rejects flagged by downstream weight or dimension checks without any stop event being logged. Quality or checkweigher data trends show out-of-tolerance readings clustering in time with feeder parameter excursions.

Countermeasure

Engineering guidance

Recalibrate and periodically verify the dosing/feeding mechanism against reference weights or flow standards, and tighten the control loop tuning or add closed-loop weight feedback to the feeder. Implement preventive maintenance on wear-prone metering components and set tighter in-process tolerance alarms so drift is caught before it generates nonconforming product.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 3.40 % · as reported: “dosing deviations”
    Show verbatim quote
    mainly caused by mechanical failures due to the lack of preventive maintenance (48.4%), high levels of waste reprocessing (31.4%), and dosing deviations (3.4%)