foratvise
Get Started
Process defects (scrap and rework)

Excessive Scalding

Process defects (scrap and rework)QualityCooking and frying

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 47 % of the line's lost time. Reported by 0 of the 57 studies that could observe it (sparse evidence).

What happens

Product remains exposed to the hot water or steam scalding medium for longer than required, or at a temperature above the intended set point, because of poor control-loop tuning, sensor drift, or mismatched conveyor/belt speed relative to scalder residence time. This thermal over-exposure overcooks the surface tissue, degrades color and texture, and increases moisture loss, producing out-of-specification product.

What is done about it

Retune and periodically calibrate the scalder temperature and dwell-time control loops, verify sensor accuracy, and synchronize conveyor or belt speed with the intended residence time. Configure automated alarms for set-point deviation so operators can intervene before product is affected.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.6%]
Expected share of lost time
0.2% [0.0–0.7%]
Share of lost time when present
47% [34–59%]
Studies / units
57 / 69
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.6%]5 studies
  • Soft drinks, bottled water and juices
    0.6% [0.0–2.4%]1 study
  • Brewing, wine and spirits
    0.6% [0.1–2.5%]0 studies
  • Bakery and pasta
    0.5% [0.0–1.9%]24 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.4%]2 studies
  • Fruit and vegetable processing
    0.6% [0.0–2.7%]2 studies
  • Grain and oilseed milling
    0.6% [0.0–2.6%]0 studies
  • Sugar and confectionery
    0.6% [0.1–2.1%]8 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.0–2.4%]4 studies
  • Animal feed and pet food
    0.6% [0.0–2.5%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.3%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Product remains exposed to the hot water or steam scalding medium for longer than required, or at a temperature above the intended set point, because of poor control-loop tuning, sensor drift, or mismatched conveyor/belt speed relative to scalder residence time. This thermal over-exposure overcooks the surface tissue, degrades color and texture, and increases moisture loss, producing out-of-specification product.

How it looks in SCADA data

Engineering guidance

SCADA/MES trends show scalder temperature or dwell-time readings exceeding the programmed set point band, often accompanied by conveyor speed deviations or control-loop oscillation. These deviations correlate in time with spikes in downstream inspection rejects or quality-hold counters, without any associated equipment fault alarm.

Countermeasure

Engineering guidance

Retune and periodically calibrate the scalder temperature and dwell-time control loops, verify sensor accuracy, and synchronize conveyor or belt speed with the intended residence time. Configure automated alarms for set-point deviation so operators can intervene before product is affected.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of loss events: 20.8 % · as reported: “excessive scalding”
    Show verbatim quote
    As principais causas de condenação total foram contaminação, escaldagem excessiva e evisceração retardada (57,0, 20,8 e 16,8%, respectivamente) totalizando 94,6% das condenações, conforme apresentado na Figura 1.