Cooking and frying
Hot-water blanching of cut green beans before freezing
In short
Cooking and frying can use at most 83 of every 100 planned hours. The rest goes to limits no plant can avoid.
- 83usable at most
- 17are a physical limit
The three limits that set it
Running time: up to 96 %
The rest are stops imposed by physics or by regulation: cleaning, changeovers, defrosting.
Speed: up to 86 %
How close to its maximum speed it can run without damaging the product or the equipment.
Good product: up to 100 %
Some product falls outside specification even with the process well under control.
Technical detail
Uncertainty intervals, physical models per station and sources, for anyone who wants to check each figure.
1Scenario
Washed green beans (Phaseolus vulgaris), stemmed and cut into segments about 5 cm long and 9.5 mm in diameter, pass through a continuous hot-water blancher at about 92 °C and are then cooled and frozen. Blanching must inactivate the enzymes that would spoil colour, flavour and texture during frozen storage; peroxidase, the most heat-resistant of them, is the industrial indicator. The slowest-heating point of each bean, its centre, must receive the reference treatment. The same ceiling is applied to the blanching of other vegetables cut to a similar size as an approximation (derivation, section 7).
2Results
- TheoreticalThermodynamic minimum energy per kg of blanched beans0 kJ/kg
- Heat absorbed by the beans without recovery (to the mass-average temperature at the design residence time)263 [215–281] kJ/kg
- Best available techniqueState-of-the-art on-site energy of blanching for frozen vegetables (DOE)205 kJ/kg
- TypicalCurrent typical on-site energy of blanching for frozen vegetables (DOE)372 kJ/kg
- Heat absorbed by the beans over the state-of-the-art blanching energy1.29 [1.05–1.37]
- Specific heat of the beans (Choi-Okos, USDA composition)3.9569 [3.9532–3.9583] kJ/kg/K
- Thermal diffusivity of the beans1.55 × 10⁻⁷ [1.54 × 10⁻⁷–1.56 × 10⁻⁷] m²/s
- Biot number h R / k of the mean bean7.61 [5.46–9.80]
- Bean diameter for which the residence time is set (capability margin)11.7 [11.0–12.4] mm
- TheoreticalMinimum residence time: centre of the mean bean reaches the reference treatment194 [169–272] s
- Residence time of the capable process (largest beans within the margin)225 [200–305] s
- TypicalTypical residence time of green beans in industrial blanchers500 s
- TheoreticalMaximum throughput per unit of blancher hold-up (kg/h per kg held)18.6 [13.2–21.3] 1/h
- TypicalThroughput per unit of hold-up at the typical residence time7.20 1/h
- TheoreticalMaximum yield (no mass has to leave the product)1.00
- Share of beans whose centre stays below the reference treatment0.00135 [0.00026–0.00580]
- TheoreticalMaximum OEE quality factor0.9987 [0.9942–0.9997]
- TheoreticalMaximum availability (daily minimum cleaning and water reheating)0.964 [0.952–0.975]
- TypicalAvailability with a typical cleaning duration0.917 [0.892–0.941]
- TheoreticalMaximum performance factor: minimum residence time over the residence time of the capable process0.861 [0.809–0.914]
- TheoreticalPhysics-bounded OEE0.828 [0.778–0.880]
3Ceilings per dimension
- Theoretical
- Best available technique
- Best documented
- Typical
- TheoreticalThermodynamic minimum energy per kg of blanched beans0 kJ/kg
- TheoreticalDOE bandwidth study: thermodynamic minimum of blanching for frozen vegetables set to zero (minimal chemical conversions) · Benchmark0 kJ/kg
- Best available techniqueState-of-the-art on-site energy of blanching for frozen vegetables (DOE)205 kJ/kg
- TypicalCurrent typical on-site energy of blanching for frozen vegetables (DOE)372 kJ/kg
- TheoreticalMinimum residence time: centre of the mean bean reaches the reference treatment194 [169–272] s
- TypicalTypical residence time of green beans in industrial blanchers500 s
- TheoreticalMaximum throughput per unit of blancher hold-up (kg/h per kg held)18.6 [13.2–21.3] 1/h
- TypicalThroughput per unit of hold-up at the typical residence time7.20 1/h
- TheoreticalMaximum yield (no mass has to leave the product)1.00
- TheoreticalMaximum OEE quality factor0.9987 [0.9942–0.9997]
- TheoreticalMaximum availability (daily minimum cleaning and water reheating)0.964 [0.952–0.975]
- TypicalAvailability with a typical cleaning duration0.917 [0.892–0.941]
- TheoreticalMaximum performance factor: minimum residence time over the residence time of the capable process0.861 [0.809–0.914]
- TheoreticalPhysics-bounded OEE0.828 [0.778–0.880]
4Loss cascade
- TheoreticalBest available techniqueEnergy per unit of product0 kJ/kg → 205 kJ/kg (gap 205 kJ/kg)
The thermodynamic minimum is zero: blanching causes no significant net chemical change, and in the reversible limit the heat that warms the beans would be returned when they are cooled before freezing (the cooling water or air preheating the incoming beans). Without any recovery the blancher must deliver at least the heat the beans absorb, about two hundred and sixty kilojoules per kilogram for a rise from 25 °C to about 90 °C. The state-of-the-art level of the DOE study lies below that no-recovery heat, which is only possible with heat recovery: belt blanchers with water cooling preheat the incoming product with the heat released in the cooling zone, the technique the BREF calls the most energy-efficient.
- Best available techniqueTypicalEnergy per unit of product205 kJ/kg → 372 kJ/kg (gap 167 kJ/kg)
Current typical blanchers lose heat through open water surfaces and steam leaks at the product inlet and outlet (rotary valves and water seals reduce them), with the overflow of hot water that is replaced to limit the organic load, through uninsulated walls, and during idle running between products; they also heat the beans without recovering the heat removed in cooling.
- TheoreticalTypicalCycle or residence time194 [169–272] s → 500 s (gap 306 s)
The theoretical residence time brings the centre of the mean bean to the reference treatment with the documented bath coefficient. The capable process must cover the thickest beans (the capability margin of the diameter), and plants blanch longer still: the residence time is set for the coarsest grade and variety of the season, for the qualitative peroxidase test (which reacts to small residual activity of heat-stable isoenzymes) and for a safety margin against fluctuations of water temperature and load. The typical residence time of about 500 s is about two and a half times the theoretical time.
- TheoreticalTypicalQuality
Beans thicker than the design diameter stay under-blanched. Real lines add colour and texture defects from over-blanching of thin beans, which share the residence time of the thick ones, and uneven residence in the blancher (back-mixing of the screw or the belt).
5Physics-bounded OEE
- Loading time (ideal)1.000
- Availabilityfactor 0.964 [0.952–0.975]0.964 (−0.036)
- Performancefactor 0.861 [0.809–0.914]0.829 (−0.134)
- Qualityfactor 0.9987 [0.9942–0.9997]0.828 (−0.001)
- Physics-bounded OEE0.828 [0.778–0.880]
6Full derivation
Scope. Washed, stemmed green beans (Phaseolus vulgaris) cut into segments about 5 cm long and 9.5 mm in diameter pass through a continuous hot-water blancher at about 92 °C and are then cooled and frozen. This is the operation cooking_frying of the frozen-vegetable process. Blanching must inactivate the enzymes that would otherwise spoil colour, flavour and texture during frozen storage; peroxidase, the most heat-resistant of them, is the indicator used by industry. Symbols, values, units, uncertainty distributions and sources are listed in the parameter table generated from config/physics/cooking.yaml.
1. Mass balance — maximum yield
Blanching does not require any mass to leave the product. Hot water leaches some soluble solids and the tissue takes up or loses a little water, but neither is needed for the operation: a steam blancher or a shorter contact removes them without changing the purpose of the step. The yield ceiling is therefore
Leaching losses, which grow with the blanching intensity, are technology losses; they are mass losses of conforming product and would be reported as yield, never inside the OEE.
2. Energy balance — minimum energy per unit of product
Thermodynamic minimum. Blanching causes no significant net chemical change. In the reversible limit the heat that warms the beans would be returned when they are cooled before freezing, for example by preheating the incoming beans with the cooling water. The thermodynamic minimum is zero, as the US DOE bandwidth study also sets for blanching of frozen vegetables ("set to zero due to minimal chemical conversions").
Heat absorbed by the product without recovery. A blancher that recovers nothing must deliver at least the heat the beans absorb. Per kilogram it is
where is the entry temperature, the water temperature, the mass-average dimensionless temperature of the bean of design diameter at the end of the design residence time (section 3), and the specific heat. The specific heat, the density and the thermal conductivity come from the Choi–Okos composition model (meo.physics.foodprops) with the USDA composition of raw green beans: water 90.32 %, protein 1.83 %, fat 0.22 %, ash 0.66 %, carbohydrate by difference 6.97 % of which 2.7 % is dietary fibre (treated separately by Choi and Okos). With the point values = 3.96 kJ kg⁻¹ K⁻¹ and ≈ 263 kJ/kg.
The energy ceilings. Theoretical: 0. Best available technique: the state-of-the-art on-site intensity of blanching for frozen vegetables in the DOE study, 88 Btu/lb (205 kJ/kg). Typical: the current typical intensity of the same row, 160 Btu/lb (372 kJ/kg). The state-of-the-art value lies below the no-recovery heat (the output product_heat_over_bat is their ratio), which is possible only with heat recovery: the BREF describes the belt blancher with water cooling, in which the heat released in the cooling zone preheats the incoming product, as the most energy-efficient blanching technique, with 0.09 t of steam per t of frozen vegetables. That steam figure is listed as a benchmark but not compared, because it is a mass of steam; at the latent heat of 7 bar steam it is of the same order as the DOE state of the art. The DOE practical minimum (75 Btu/lb) is a projection with technologies under research and carries no ceiling.
3. Rate-limiting step — minimum residence time
Heat conduction. A bean segment is about five times longer than it is thick, so it is treated, as in the source study, as an infinite cylinder of radius . Heat enters from the water through a surface coefficient and moves to the centre by conduction:
The exact solution (the Heisler–Fourier series of the cylinder) at the centre is
with the Fourier number , the ratio of the elapsed time to the time heat needs to diffuse over the radius, and the Biot number , the ratio of the internal conduction resistance to the surface resistance. and are Bessel functions of the first kind; the eigenvalues are found by bisection between consecutive zeros of and . The mass-average temperature used in section 2 has the coefficients . The bath coefficient = 1000 W m⁻² K⁻¹ was fitted by the source study to measured bean temperatures in hot-water baths; with it ≈ 7.6, so both the surface and the inside resist the heat flow and the centre lags clearly behind the water.
Enzyme criterion. Peroxidase inactivation is first order with an Arrhenius dependence on temperature, so any temperature history can be expressed as an equivalent time at a reference temperature :
The reference treatment is the example the BREF gives for blanching of vegetables, 75 °C for 5 min. The bean is blanched when its slowest-heating point, the centre, has received it: the minimum residence time is the first time with min, found on a 2 s grid with linear interpolation. The activation energy is 57 kJ/mol, one of the values listed for green-bean peroxidase in the appendix of the source study; the uncertainty range spans the three green-bean values of that table, 48 to 77 kJ/mol. The same study fits 0.37 MJ/mol to its own data; with such a high activation energy the criterion becomes almost a threshold on the centre temperature and the minimum time is shorter. With the point values ≈ 194 s for the mean bean.
Maximum throughput. A blancher of hold-up (mass of beans inside) delivers at most , so the throughput per unit hold-up is ≈ 18.6 h⁻¹; at the typical industrial residence time of about 500 s it is 7.2 h⁻¹. Two simplifications lengthen the computed time slightly: heat entering through the cut ends is neglected (exact for the middle of a long segment) and so is the inactivation during the cooling that follows. The time is therefore the conduction-limited minimum for the documented bath coefficient; a perfect surface () would give a shorter, strictly physical limit that no water bath reaches.
4. Process capability — quality ceiling
The beans are not all of the same thickness: in the source study 150 segments had a mean diameter of 9.5 mm and ranged from 7.2 to 11.0 mm. The range of 150 normal draws is on average = 5.30 standard deviations, so ≈ 0.72 mm. Thicker beans heat more slowly. A blancher has one residence time for all of them, so it is set for a design diameter
and the beans thicker than stay under-blanched. They are the non-conforming units counted here:
With the margin = 3 (the same convention as the other models) ≈ 11.65 mm, the design residence time is ≈ 225 s and = 0.99865. Over-blanching of the thin beans, which share the residence time of the thick ones, softens them and leaches more solids; it is a technology loss not counted in the bound.
5. Unavoidable stops — maximum availability
Leached solids, starch and plant debris accumulate in the blancher water and on the screw or belt; the water is drained and the blancher cleaned once per production day, and the refilled water must then be reheated to the blanching temperature before the first beans enter. No regulation in the registered sources fixes the interval (food-contact surfaces must be cleaned as often as necessary), so one cleaning per day is declared. The cleaning duration is linked to the minimum programme of the cleaning model (cip_time_min, about 22.5 min with its current result); that model is valid for recirculated pipe and plate circuits, so for an open blancher it is a lower bound, and a declared typical duration (1.5 h) gives availability_typical. With the reheating time :
6. Physics-bounded OEE
Scope of the bound. The theoretical label of means physics-bounded under the declared scenario: the ceiling follows from the physics of the operation for the declared product, equipment and schedule, and it is a bound only conditional on those declarations. It follows the common definition of all models: counts only stops required by regulation or forced by a physical mechanism, at their physical minimum duration, plus the start-up they force; is the ratio of the physics-limited ideal cycle to the cycle of the capable process; is the share of conforming units, and mass losses of conforming product are reported only as yield.
The capability margin lengthens the residence time, as the lethality margin does in the retort model, so it acts through performance:
The point values and the Monte Carlo intervals over the declared uncertainty of every input are reported in the output table.
7. Assumptions, validity and use for other processes
See the assumption and validity lists generated from the configuration file. The most influential inputs (sensitivity table) are the water temperature, the activation energy, the bath coefficient and the bean diameter for the residence time, the capability margin and the diameter spread for performance, and the cleaning and reheating times for availability.
Use for other processes. The codebook assigns this operation to the frozen-vegetable process, whose products include many vegetables. The same ceiling is applied to them as an approximation when they are cut to pieces with a similar smallest dimension (diced carrots, peas of 8–10 mm): the conduction solution and the criterion are the same, but each vegetable has its own peroxidase kinetics, composition and size, and a sphere or cube conducts faster than a cylinder of the same thickness, so the bean ceiling is conservative for small cubes and spheres. Steam blanching has a much larger surface coefficient; with the residence time would approach the pure conduction limit and the ceiling would be somewhat higher.
References
- van der Sman, R. G. M., Delbaere, S. M., Timmermans, R. A. H. (2026). Modeling of enzyme inactivation and quality changes during blanching of green beans. Current Research in Food Science, 12, 101424. doi:10.1016/j.crfs.2026.101424
- U.S. Department of Agriculture, Agricultural Research Service. USDA National Nutrient Database for Standard Reference, Release 28, food group 11, record 11052 (Beans, snap, green, raw), 2015.
- European Commission, Joint Research Centre. Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries, 2019 (section 8.2.2, blanching; Table 19.2).
- U.S. Department of Energy. Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing, 2017 (Table A1-1, frozen vegetables).
- Choi, Y. and Okos, M. R. (1986). Effects of temperature and composition on the thermal properties of food. In Food Engineering and Process Applications, Vol. 1, 93–101 (through the open reproductions cited by
config/physics/food_properties.yaml).
7Parameters and provenance
- 0.9032
Water mass fraction of raw green beans
Property · Fixed
Verified quoteShow verbatim quote
90.32 31 131 1.83 0.22 0.66 6.97 2.7USDA National Nutrient Database for Standard Reference, Release 28 (2015): Food Group 11, Vegetables and Vegetable Products (nutrient report) (opens in a new tab). U.S. Department of Agriculture, Agricultural Research Service, Nutrient Data Laboratory, 2015. p. 163. USDA SR28, food group 11 report (sr28fg11.pdf)
- 0.0183
Protein mass fraction
Property · Fixed
Verified quoteShow verbatim quote
90.32 31 131 1.83 0.22 0.66 6.97 2.7USDA National Nutrient Database for Standard Reference, Release 28 (2015): Food Group 11, Vegetables and Vegetable Products (nutrient report) (opens in a new tab). U.S. Department of Agriculture, Agricultural Research Service, Nutrient Data Laboratory, 2015. p. 163. USDA SR28, food group 11 report (sr28fg11.pdf)
- 0.0022
Fat mass fraction
Property · Fixed
Verified quoteShow verbatim quote
90.32 31 131 1.83 0.22 0.66 6.97 2.7USDA National Nutrient Database for Standard Reference, Release 28 (2015): Food Group 11, Vegetables and Vegetable Products (nutrient report) (opens in a new tab). U.S. Department of Agriculture, Agricultural Research Service, Nutrient Data Laboratory, 2015. p. 163. USDA SR28, food group 11 report (sr28fg11.pdf)
- 0.0066
Ash mass fraction
Property · Fixed
Verified quoteShow verbatim quote
90.32 31 131 1.83 0.22 0.66 6.97 2.7USDA National Nutrient Database for Standard Reference, Release 28 (2015): Food Group 11, Vegetables and Vegetable Products (nutrient report) (opens in a new tab). U.S. Department of Agriculture, Agricultural Research Service, Nutrient Data Laboratory, 2015. p. 163. USDA SR28, food group 11 report (sr28fg11.pdf)
- 0.0697
Carbohydrate by difference (includes the fibre; the model uses carbohydrate minus fibre, as Choi and Okos treat fibre separately)
Property · Fixed
Verified quoteShow verbatim quote
90.32 31 131 1.83 0.22 0.66 6.97 2.7USDA National Nutrient Database for Standard Reference, Release 28 (2015): Food Group 11, Vegetables and Vegetable Products (nutrient report) (opens in a new tab). U.S. Department of Agriculture, Agricultural Research Service, Nutrient Data Laboratory, 2015. p. 163. USDA SR28, food group 11 report (sr28fg11.pdf)
- 0.027
Total dietary fibre mass fraction
Property · Fixed
Verified quoteShow verbatim quote
90.32 31 131 1.83 0.22 0.66 6.97 2.7USDA National Nutrient Database for Standard Reference, Release 28 (2015): Food Group 11, Vegetables and Vegetable Products (nutrient report) (opens in a new tab). U.S. Department of Agriculture, Agricultural Research Service, Nutrient Data Laboratory, 2015. p. 163. USDA SR28, food group 11 report (sr28fg11.pdf)
- 9.5 mm
Mean diameter of the green-bean segments
Property · Fixed
Verified quoteShow verbatim quote
The mean weight of 150 individual segments was 3.32 g (range: 2.16–4.30 g), with an average diameter of 9.5 mm (range: 7.2–11.0 mm).Modeling of enzyme inactivation and quality changes during blanching of green beans (van der Sman, Delbaere, Timmermans; Current Research in Food Science 12: 101424) (opens in a new tab). Elsevier (open access, CC BY 4.0); full text served by PubMed Central, 2026. doi:10.1016/j.crfs.2026.101424; PMC13217498
- 0.717 mm
Standard deviation of the bean diameter
Property · Uniform 0.55 to 0.9 mm
ComputedRange divided by the expected range of 150 normal draws: (11.0 - 7.2) mm / d2(150), d2(150) = 5.298 (numerical integral of 1 - Phi^n - (1 - Phi)^n), giving 0.717 mm; range and sample size from the same passage as d_mean. The uniform range 0.55-0.90 mm is a declared allowance for other lots and varieties.
- 1,000 W/m²/K
Surface heat transfer coefficient of the hot-water bath
Technology · Uniform 700 to 1,300 W/m²/K
Verified quoteShow verbatim quote
Good agreement was obtained for hext=1000 W m−2 K−1, as shown in Fig. 3Modeling of enzyme inactivation and quality changes during blanching of green beans (van der Sman, Delbaere, Timmermans; Current Research in Food Science 12: 101424) (opens in a new tab). Elsevier (open access, CC BY 4.0); full text served by PubMed Central, 2026. doi:10.1016/j.crfs.2026.101424; PMC13217498
- 92 °C
Temperature of the blanching water
Technology · Uniform 82 to 94 °C
Verified quoteShow verbatim quote
Data from experiment 1 were used, performed at bath temperatures of Te=42, 54, 72, and 92 °C.Modeling of enzyme inactivation and quality changes during blanching of green beans (van der Sman, Delbaere, Timmermans; Current Research in Food Science 12: 101424) (opens in a new tab). Elsevier (open access, CC BY 4.0); full text served by PubMed Central, 2026. doi:10.1016/j.crfs.2026.101424; PMC13217498
- 25 °C
Temperature of the beans entering the blancher
Scenario · Uniform 20 to 30 °C
Verified quoteShow verbatim quote
where T0≈25°C is the initial temperatureModeling of enzyme inactivation and quality changes during blanching of green beans (van der Sman, Delbaere, Timmermans; Current Research in Food Science 12: 101424) (opens in a new tab). Elsevier (open access, CC BY 4.0); full text served by PubMed Central, 2026. doi:10.1016/j.crfs.2026.101424; PMC13217498
- 75 °C
Temperature of the reference blanching treatment
Technology · Fixed
Verified quoteShow verbatim quote
Blanching of vegetables Variable, e.g. 75 °C/5 min Enzyme deactivation and tissue softeningBest Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (opens in a new tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. p. 785. EUR 29978 EN; JRC118627; doi:10.2760/243911
- 5 min
Holding time of the reference blanching treatment
Technology · Fixed
Verified quoteShow verbatim quote
Blanching of vegetables Variable, e.g. 75 °C/5 min Enzyme deactivation and tissue softeningBest Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (opens in a new tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. p. 785. EUR 29978 EN; JRC118627; doi:10.2760/243911
- 57 kJ/mol
Activation energy of the thermal inactivation of green-bean peroxidase
Property · Uniform 48 to 77 kJ/mol
Verified quoteShow verbatim quote
Green Beans POD biphasic ΔEa,II 57 kJ/mol Güneş and Bayindirli (1993)Modeling of enzyme inactivation and quality changes during blanching of green beans (van der Sman, Delbaere, Timmermans; Current Research in Food Science 12: 101424) (opens in a new tab). Elsevier (open access, CC BY 4.0); full text served by PubMed Central, 2026. doi:10.1016/j.crfs.2026.101424; PMC13217498
- 3
Capability margin on the bean diameter, in standard deviations
Scenario · Uniform 2.5 to 3.5
Declared assumptionOperating choice of the processor at the centre of the range 2.5-3.5 used by the other models; it sets the under-blanched share and the performance margin.
- 500 s
Typical residence time of green beans in industrial blanchers
Benchmark · Fixed
Verified quoteShow verbatim quote
Given that typical residence times of green beans in industrial blanchers are about 500 s, internal heat conduction within the bean is expected to significantly influence enzyme inactivation.Modeling of enzyme inactivation and quality changes during blanching of green beans (van der Sman, Delbaere, Timmermans; Current Research in Food Science 12: 101424) (opens in a new tab). Elsevier (open access, CC BY 4.0); full text served by PubMed Central, 2026. doi:10.1016/j.crfs.2026.101424; PMC13217498
- 88 Btu/lb
State-of-the-art on-site energy intensity of blanching, frozen vegetables (DOE bandwidth study)
Benchmark · Fixed
Verified quoteShow verbatim quote
Blanching 20,639 160 88 75 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 56. DOE/EE-1571; OSTI ID 1512366
- 160 Btu/lb
Current typical on-site energy intensity of blanching, frozen vegetables (DOE bandwidth study)
Benchmark · Fixed
Verified quoteShow verbatim quote
Blanching 20,639 160 88 75 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 56. DOE/EE-1571; OSTI ID 1512366
- 0.374294 h
Minimum duration of the daily cleaning: physical minimum of the kinetic and displacement phases plus declared hold times (output cip_time_min of the cleaning model)
Property · Triangular 0.242184, 0.374294, 0.536161 h
ComputedOutput `cip_time_min` of the cleaning model: 22.46 min [14.53, 32.17].
- 1.5 h
Typical duration of the daily cleaning of a blancher (draining, removal of debris, washing, refilling)
Scenario · Uniform 1 to 2 h
Declared assumptionDeclared typical duration; no open source with a value was found.
- 0.5 h
Reheating of the refilled blancher water to the blanching temperature
Scenario · Uniform 0.25 to 0.75 h
Declared assumptionSet by the water volume and the steam injection capacity; declared assumption.
- 24 h
Production period between two cleanings (one production day)
Scenario · Fixed
Declared assumptionNo regulation in the registered sources fixes a cleaning interval for vegetable blanchers (food-contact surfaces must be cleaned as often as necessary); one cleaning per production day is declared.
8Benchmarks
| Benchmark | Ceiling | Value | Provenance |
|---|---|---|---|
DOE bandwidth study: thermodynamic minimum of blanching for frozen vegetables set to zero (minimal chemical conversions)Show verbatim quoteBlanching 20,639 160 88 75 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 56. DOE/EE-1571; OSTI ID 1512366 | Theoretical | 0 Btu/lb | Verified quote |
DOE practical minimum of blanching for frozen vegetables (projected with technologies under research, not a documented achievement)Show verbatim quoteBlanching 20,639 160 88 75 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 56. DOE/EE-1571; OSTI ID 1512366 | — | 75 Btu/lb | Verified quote |
Steam of a belt blancher with water cooling, the most energy-efficient blanching technique of the BREF: 0.09 t of steam (7 bar) per t of frozen vegetables. Not compared: steam mass, not energy; at the latent heat of 7 bar steam (about 2.07 MJ/kg) it is about 190 kJ/kg, of the same order as the DOE state of the artShow verbatim quoteSteam (t/t frozen vegetables) 0.09Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (opens in a new tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. p. 484. EUR 29978 EN; JRC118627; doi:10.2760/243911 | — | 0.09 | Verified quote |
Shortest residence time in blanchers for fruits and vegetables in general (about 1 min). Not compared: it covers leafy and thin products whose conduction time is much shorter than that of a 9.5 mm beanShow verbatim quoteThe residence time in the blancher can vary from approximately 1 to 5 minutes depending on the fruit or vegetable being blanched.Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (opens in a new tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. p. 483. EUR 29978 EN; JRC118627; doi:10.2760/243911 | Best documented | 1 min | Verified quote |
Longest residence time in blanchers for fruits and vegetables in general (about 5 min)Show verbatim quoteThe residence time in the blancher can vary from approximately 1 to 5 minutes depending on the fruit or vegetable being blanched.Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (opens in a new tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. p. 483. EUR 29978 EN; JRC118627; doi:10.2760/243911 | Typical | 5 min | Verified quote |
9Unavoidable stops
- Daily cleaning of the blancherDeclared assumption
Leached solids, starch and plant debris accumulate in the blancher water and on the conveying screw or belt (blanching water carries a high organic load); the water is drained and the equipment cleaned once per production day. The minimum duration is the cleaning model's programme, a lower bound for an open blancher.
- Reheating of the blancher water after cleaningDeclared assumption
The refilled water must reach the blanching temperature before the first beans enter; the time is the water mass times the temperature rise divided by the steam injection capacity.
10Assumptions
- Each bean segment is an infinite cylinder (length about five times the diameter, as in the source study); heat enters only through the curved surface, so the centre time is an upper estimate for the short end pieces and exact for the middle of long segments.
- Thermal properties are constant, evaluated with the Choi–Okos model at the mean of the entry and water temperatures from the USDA composition; the internal air of the pod and the seeds are not resolved.
- Peroxidase inactivation is first order with an Arrhenius temperature dependence, so the treatment is measured by the equivalent time at the reference temperature; the reference treatment (75 °C for 5 min at the slowest point) is the generic example of the BREF, not a value fitted to green beans. Inactivation during cooling after the blancher is neglected, which lengthens the computed time slightly.
- Bean diameters are normally distributed; the residence time is set for the diameter d + z sigma_d, beans beyond it are under-blanched and count as quality losses; the margin acts through performance (minimum residence time of the mean bean over that of the design bean). Leaching and water uptake are not losses required by the operation: yield_max = 1.
- Availability: the daily cleaning is counted at the minimum programme duration of the cleaning model (from_model link) and the reheating of the refilled water it forces at a declared duration. The cleaning model is valid for recirculated pipe and plate circuits; an open blancher with a screw or belt also needs draining and removal of debris, so the linked duration is a lower bound and a declared typical duration gives availability_typical. No regulation fixes the cleaning interval; one cleaning per production day is declared.
11Range of validity
- Hot-water blanching of cut green beans of 7–11 mm diameter at 82–94 °C before freezing.
- Approximation for other vegetables cut to pieces with a similar smallest dimension (diced carrots, peas); their own peroxidase kinetics and properties change the times.
12Sensitivity
- Temperature of the blanching waterelasticity -0.366Spearman ρ -0.49
- Temperature of the reference blanching treatmentelasticity +0.301Spearman ρ —
- Standard deviation of the bean diameterelasticity -0.149Spearman ρ -0.63
- Capability margin on the bean diameter, in standard deviationselasticity -0.135Spearman ρ -0.37
- Activation energy of the thermal inactivation of green-bean peroxidaseelasticity -0.104Spearman ρ -0.38
- Holding time of the reference blanching treatmentelasticity +0.071Spearman ρ —
- Production period between two cleanings (one production day)elasticity +0.038Spearman ρ —
- Reheating of the refilled blancher water to the blanching temperatureelasticity -0.022Spearman ρ -0.20
- Temperature of the beans entering the blancherelasticity +0.017Spearman ρ +0.05
- Minimum duration of the daily cleaning: physical minimum of the kinetic and displacement phases plus declared hold times (output cip_time_min of the cleaning model)elasticity -0.016Spearman ρ -0.07
- Mean diameter of the green-bean segmentselasticity +0.006Spearman ρ —
- Water mass fraction of raw green beanselasticity +0.001Spearman ρ —
- Carbohydrate by difference (includes the fibre; the model uses carbohydrate minus fibre, as Choi and Okos treat fibre separately)elasticity -0.001Spearman ρ —
- Protein mass fractionelasticity 0.000Spearman ρ —
- Total dietary fibre mass fractionelasticity 0.000Spearman ρ —
- Fat mass fractionelasticity 0.000Spearman ρ —
- Ash mass fractionelasticity 0.000Spearman ρ —
- Surface heat transfer coefficient of the hot-water bathelasticity 0.000Spearman ρ +0.02
- Output rises with the parameter
- Output falls with the parameter
13Validation checks
- Dimensional analysis21 outputs converted to their declared unitsPassed
- Every cited value verified against its source21 verified, 0 failedPassed
- No documented value beats the theoretical limitPassed
- Ceilings in physical orderPassed
- Fractions within 0 and 1Passed
14Causes of loss in this operation
- Unwanted crystallization in cooked productProcess defects (scrap and rework)0.8% [0.1–2.3%]D57 studies
- Toasting degree deviation (under/over-toasting)Process defects (scrap and rework)0.5% [0.1–1.6%]D57 studies
- Excessive ScaldingProcess defects (scrap and rework)0.5% [0.1–1.6%]D57 studies
- Raw material staging and setup for cookingSetup and adjustments0.4% [0.1–1.5%]D57 studies
- Cooking equipment start-up and warm-upSetup and adjustments0.4% [0.1–1.4%]D57 studies
15References
- Modeling of enzyme inactivation and quality changes during blanching of green beans (van der Sman, Delbaere, Timmermans; Current Research in Food Science 12: 101424) (opens in a new tab). Elsevier (open access, CC BY 4.0); full text served by PubMed Central, 2026. doi:10.1016/j.crfs.2026.101424; PMC13217498
- USDA National Nutrient Database for Standard Reference, Release 28 (2015): Food Group 11, Vegetables and Vegetable Products (nutrient report) (opens in a new tab). U.S. Department of Agriculture, Agricultural Research Service, Nutrient Data Laboratory, 2015. p. 163. USDA SR28, food group 11 report (sr28fg11.pdf)
- Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (opens in a new tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. p. 785. EUR 29978 EN; JRC118627; doi:10.2760/243911
- Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 56. DOE/EE-1571; OSTI ID 1512366
- doi:10.1016/j.crfs.2026.101424 — Bean geometry, bath heat transfer coefficient, initial and bath temperatures, typical industrial residence time and the activation energies of peroxidase inactivation.

