foratvise
Get Started
Setup and adjustments

Fallen-bottle detection sensor adjustment

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 56 % of the line's lost time. Reported by 2 of the 112 studies that could observe it (sparse evidence).

What happens

During changeover or format setup, the photoelectric or proximity sensor that detects fallen or tipped bottles on the packaging line must be repositioned and its height or alignment recalibrated to match the new container geometry. Until the sensor is correctly aligned it cannot reliably distinguish a fallen container from a normal one, so the line is held in adjustment mode rather than running production.

What is done about it

Use quick-adjust mounting brackets with pre-set, labeled height positions for each container format so the sensor can be repositioned without trial-and-error, and validate detection with a standard test piece before resuming the line. Document sensor settings per SKU in the changeover procedure to shorten future adjustments.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.4%]
Expected share of lost time
0.3% [0.1–0.8%]
Share of lost time when present
56% [44–66%]
Studies / units
112 / 155
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.1%]14 studies
  • Soft drinks, bottled water and juices
    0.7% [0.1–2.3%]33 studies
  • Brewing, wine and spirits
    0.5% [0.1–2.0%]14 studies
  • Bakery and pasta
    0.6% [0.1–2.3%]6 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.4%]6 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.4%]4 studies
  • Grain and oilseed milling
    0.6% [0.1–2.0%]4 studies
  • Sugar and confectionery
    0.6% [0.1–2.3%]4 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.3%]8 studies
  • Animal feed and pet food
    0.6% [0.1–2.1%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.1%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During changeover or format setup, the photoelectric or proximity sensor that detects fallen or tipped bottles on the packaging line must be repositioned and its height or alignment recalibrated to match the new container geometry. Until the sensor is correctly aligned it cannot reliably distinguish a fallen container from a normal one, so the line is held in adjustment mode rather than running production.

How it looks in SCADA data

Engineering guidance

SCADA/MES logs show a changeover or setup machine state coinciding with repeated manual sensor-position or threshold changes, often accompanied by short bursts of fallen-container alarms before stabilizing. No production counts accumulate during this window, and the event is time-stamped between the last good unit of the previous run and the first good unit of the new run.

Countermeasure

Engineering guidance

Use quick-adjust mounting brackets with pre-set, labeled height positions for each container format so the sensor can be repositioned without trial-and-error, and validate detection with a standard test piece before resuming the line. Document sensor settings per SKU in the changeover procedure to shorten future adjustments.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 10.0 min · as reported: “Adjusting the height of the fallen-bottle detection sensor unit”
    Show verbatim quote
    ปรับระยะความสูงชุดตรวจสอบขวดล้ม 1 10
  2. Lost time: 15.0 min · as reported: “Adjusting the fallen-bottle detection sensor”
    Show verbatim quote
    ปรับเซ็นเซอร์ตรวจสอบขวดล้ม 1 15