foratvise
Get Started
Filling and packaging line

Packaging (forming, sealing, wrapping, case packing, palletizing)

Heat sealing in intermittent-motion form-fill-seal packaging

Validated modelOEE bound 0.986 [0.959–0.995]20,000 Monte Carlo samples · seed 20261115 · computed November 16, 2026

In short

Packaging (forming, sealing, wrapping, case packing, palletizing) can use at most 99 of every 100 planned hours. The rest goes to limits no plant can avoid.

  1. 99usable at most
  2. 1are a physical limit

The three limits that set it

Running time: up to 100 %

The rest are stops imposed by physics or by regulation: cleaning, changeovers, defrosting.

Speed: up to 99 %

How close to its maximum speed it can run without damaging the product or the equipment.

Good product: up to 100 %

Some product falls outside specification even with the process well under control.

See the technical detail

Technical detail

Uncertainty intervals, physical models per station and sources, for anyone who wants to check each figure.

1Scenario

A vertical form-fill-seal machine forms pillow bags of frozen vegetables or a similar dry product from a reel of polyethylene film. Each cycle the film is advanced by one bag length, the cross-sealing jaws close on two layers of film, hold them at constant jaw temperature for the dwell time (the top seal of one bag and the bottom seal of the next are made together) and open again. The longitudinal fin seal is made while the film advances. The cross-seal dwell is the physics-limited step.

Provenance of inputsComputed1Declared assumption27Verified quote8

2Results

Point value from the nominal parameters and 95% interval from 20,000 Monte Carlo draws of the uncertain parameters.
  • Density of the semicrystalline sealant film (two-phase rule)914 [900–928] kg/m³
  • Specific heat of the semicrystalline film (crystalline and amorphous heat capacities weighted by crystallinity)1.95 [1.89–2.01] kJ/kg/K
  • Thermal diffusivity of the film0.186 [0.143–0.250] mm²/s
  • Fourier number at which the seal interface reaches the sealing temperature0.676 [0.584–0.819]
  • TheoreticalMinimum jaw dwell time (interface reaches the sealing temperature, ideal contact)0.00911 [0.00405–0.02034] s
  • Dwell time with the capability margin (jaw-temperature and film-thickness tolerances; declared tolerances, not a documented BAT)0.0146 [0.0064–0.0346] s
  • TypicalDwell time in operation (declared scenario)0.300 [0.162–0.589] s
  • Minimum indexing time per cycle (film advance and jaw stroke, bang-bang motion)0.370 [0.283–0.464] s
  • TheoreticalMaximum cycles per minute with the minimum dwell158 [126–205] 1/min
  • Cycles per minute with the capability-limited dwell (the rate of the capable process)156 [125–202] 1/min
  • TypicalCycles per minute with the operating dwell (declared scenario)89.6 [61.2–122.7] 1/min
  • Film mass in the seal areas per pack (two layers)0.393 [0.282–0.544] g
  • TheoreticalThermodynamic minimum energy per pack (the seal returns to ambient)0 J
  • Minimum heating duty per pack without heat recovery (seal mass at the sealing temperature, fusion included; a computed minimum, not a documented BAT)124 [87–182] J
  • Heat absorbed per pack by the film at the capability-limited dwell (conductive jaws)141 [100–207] J
  • TypicalHeat absorbed per pack by the film at the operating dwell (film close to jaw temperature)147 [104–214] J
  • Minimum sealing heat per kg of packed product0.247 [0.175–0.365] kJ/kg
  • Sealing heat absorbed by the film per kg of packed product at the operating dwell0.293 [0.207–0.429] kJ/kg
  • Nominal interface temperature at the capability-limited dwell139 [126–152] °C
  • Standard deviation of the interface temperature at the capability-limited dwell4.01 [2.77–5.59] K
  • Share of seals whose interface stays below the sealing temperature9.75 × 10⁻⁷ [4.14 × 10⁻⁹–8.55 × 10⁻⁵]
  • Share of seals overheated beyond the upper limit of the sealing window7.62 × 10⁻²⁴ [1.87 × 10⁻¹²⁰–1.10 × 10⁻⁶]
  • TheoreticalMaximum OEE quality factor (seal integrity)1.00000 [0.99990–1.00000]
  • Mean film speed at the capability-limited rate39.0 [31.1–50.4] m/min
  • Run time of one reel at the capability-limited rate51.2 [25.6–109.0] min
  • TheoreticalMaximum film yield (splice and start-up waste)0.9982 [0.9955–0.9994]
  • TheoreticalMaximum availability (no stop is forced by physics or regulation: reel splices are removable by an automatic splicer, changeovers are scenario)1.00
  • Availability with declared manual splices and changeovers0.909 [0.815–0.963]
  • TheoreticalPerformance factor: minimum cycle over capability-limited cycle0.986 [0.959–0.995]
  • TheoreticalPhysics-bounded OEE0.986 [0.959–0.995]
  • OEE with declared manual splices and changeovers0.896 [0.799–0.950]

3Ceilings per dimension

Each dimension shows the ceilings the model computes and, where units are comparable, documented benchmarks. Colour and marker shape identify the ceiling type throughout the Oracle.
  • Theoretical
  • Best available technique
  • Best documented
  • Typical
Cycle or residence times · lower is better
  • TheoreticalMinimum jaw dwell time (interface reaches the sealing temperature, ideal contact)0.00911 [0.00405–0.02034] s
  • TypicalDwell time in operation (declared scenario)0.300 [0.162–0.589] s
Throughput1/min · higher is better
  • TheoreticalMaximum cycles per minute with the minimum dwell158 [126–205] 1/min
  • TypicalCycles per minute with the operating dwell (declared scenario)89.6 [61.2–122.7] 1/min
Energy per unit of productJ · lower is better
  • TheoreticalThermodynamic minimum energy per pack (the seal returns to ambient)0 J
  • TypicalHeat absorbed per pack by the film at the operating dwell (film close to jaw temperature)147 [104–214] J
Qualityhigher is better
  • TheoreticalMaximum OEE quality factor (seal integrity)1.00000 [0.99990–1.00000]
Yieldhigher is better
  • TheoreticalMaximum film yield (splice and start-up waste)0.9982 [0.9955–0.9994]
Availabilityhigher is better
  • TheoreticalMaximum availability (no stop is forced by physics or regulation: reel splices are removable by an automatic splicer, changeovers are scenario)1.00
Performancehigher is better
  • TheoreticalPerformance factor: minimum cycle over capability-limited cycle0.986 [0.959–0.995]
OEEhigher is better
  • TheoreticalPhysics-bounded OEE0.986 [0.959–0.995]

4Loss cascade

What separates each ceiling from the next one, from the physical limit to typical operation.
  1. TheoreticalTypicalCycle or residence time
    0.00911 [0.00405–0.02034] s → 0.300 [0.162–0.589] s (gap 0.291 s)

    The minimum dwell brings the nominal seal interface exactly to the sealing temperature with ideal (zero-resistance) contact between jaw and film. Any real jaw temperature oscillates around its set point and the film thickness varies along the web, so a capable process must hold the jaws until the interface is z standard deviations of jaw temperature above the sealing temperature on the thickest film of the tolerance band. Because the remaining temperature difference decays exponentially with the Fourier number, the last few kelvin cost a disproportionate share of the dwell. Operating dwells are one or two orders of magnitude longer than the conduction limit of a bare polyethylene film. The causes are thermal resistances that the ideal model leaves out: non-stick jaw covers, imperfect contact on wrinkles and fin overlaps, outer laminate layers (oriented polypropylene or polyester) that must be crossed before the sealant, the latent heat of melting that slows the advance of the melt front, and the time the molten interface needs for chain interdiffusion and for the seal to gain strength while still under pressure.

  2. TheoreticalTypicalThroughput
    158 [126–205] 1/min → 89.6 [61.2–122.7] 1/min (gap 68.8 1/min)

    With the indexing motion (film advance and jaw stroke) fixed by the acceleration the film and the carriage can stand, the cycle rate falls from the theoretical value (minimum dwell) to the capable value and then to the operating value in proportion to the dwell gaps above; at operating dwells the dwell, not the motion, dominates the cycle.

  3. TheoreticalTypicalEnergy per unit of product
    0 J → 147 [104–214] J (gap 147 J)

    The seal is heated and cools back to ambient, so in the reversible limit (ideal heat recovery) no net energy is needed: the thermodynamic minimum is zero, as in the DOE bandwidth study. Without heat recovery the least heat is that of raising only the seal mass to the sealing temperature and melting its crystalline fraction. Conductive jaws at a constant temperature above the sealing temperature heat the whole film thickness towards the jaw temperature; at operating dwells the film reaches it, so the absorbed heat grows with (T_jaw - T0) instead of (T_s - T0). The heat absorbed by the film is still a small fraction of the electricity of the machine: jaw heaters lose heat continuously by convection and radiation and through the jaw mountings, and the drives, vacuum and compressed air dominate the energy of a packaging step, which is why the documented energy intensities of packaging are orders of magnitude above the sealing heat.

5Physics-bounded OEE

The highest OEE the operation can reach: availability, performance and quality limited only by unavoidable stops and physical capability.
Fraction of loading time that remains after each unavoidable loss. Axis starts at 0.90.
  • Loading time (ideal)
    1.000
  • Availability
    factor 1.00
    1.000 (−0.000)
  • Performance
    factor 0.986 [0.959–0.995]
    0.986 (−0.014)
  • Quality
    factor 1.00000 [0.99990–1.00000]
    0.986 (−0.000)
  • Physics-bounded OEE
    0.986 [0.959–0.995]

6Full derivation

Mass and energy balances, rate-limiting step, process capability and unavoidable stops, with every term explained.

Scope. An intermittent-motion vertical form-fill-seal machine makes pillow bags from a reel of polyethylene film. Each cycle the film advances one bag length, the cross-sealing jaws close on two film layers, hold them at a constant jaw temperature for the dwell time and open again; the longitudinal fin seal is made while the film moves. The cross-seal dwell is the physics-limited step. Symbols and their values, units, uncertainty distributions and sources are listed in the parameter table generated from config/physics/packaging.yaml. Numbers quoted here are point values; the output table gives the Monte Carlo intervals.

1. Mass balance — maximum film yield

Sealing consumes no product and no film: the seal is part of the bag. Film is lost only where it does not become a saleable bag. In a fin-sealed pillow bag there is no trim, so two losses remain:

  • Splice waste. A reel holds a finite length LrL_r. When it runs out the new web is spliced to the old one and a length LwL_w around the splice is discarded.
  • Start-up waste. After each changeover the machine needs nsun_{su} bags to stabilise registration, bag length and seal quality.

During a production campaign of duration tcampt_{camp} at web speed vv the film used for good bags is Lcamp=v tcampL_{camp} = v\,t_{camp}, the number of reels is nr=Lcamp/Lrn_r = L_{camp}/L_r, and

Ymax=LcampLcamp+nrLw+nsuLp=0.998,Y_{max} = \frac{L_{camp}}{L_{camp} + n_r L_w + n_{su} L_p} = 0.998,

where LpL_p is the film length per bag. No open source documents splice or start-up waste, so LwL_w and nsun_{su} are declared scenario values.

2. Energy balance — minimum energy per pack

Film properties. The sealant is semicrystalline polyethylene with mass crystallinity wcw_c. Its density follows the two-phase rule from the densities of the crystalline and amorphous phases at 298 K (ρc\rho_c = 1.0030 and ρa\rho_a = 0.8519 Mg/m³, Gaur and Wunderlich, 1981):

1ρ=wcρc+1−wcρa  ⇒  ρ=914 kg/m3.\frac{1}{\rho} = \frac{w_c}{\rho_c} + \frac{1-w_c}{\rho_a} \;\Rightarrow\; \rho = 914\ \text{kg/m}^3 .

The specific heat weights the recommended heat capacities of crystalline and amorphous polyethylene at 310 K (Cp,cC_{p,c} = 22.38 and Cp,aC_{p,a} = 31.33 J/(mol K) per CH2 repeat unit, MM = 14.027 g/mol):

cp=wcCp,c+(1−wc)Cp,aM=1.95 kJ/(kg K).c_p = \frac{w_c C_{p,c} + (1-w_c) C_{p,a}}{M} = 1.95\ \text{kJ/(kg K)} .

Heat capacity rises with temperature, so using the 310 K value over the whole heating range underestimates the sensible heat: every energy computed with it is a lower bound. Melting the crystalline fraction absorbs wc Δhf/Mw_c\,\Delta h_f/M, with the heat of fusion of fully crystalline polyethylene Δhf\Delta h_f = 4.051 kJ/mol at 380 K.

Seal mass. The cross seal covers the bag width WW times the jaw height hjh_j (the top seal of one bag and the bottom seal of the next), the fin seal the bag length LpL_p times the fin width wfw_f; both join two layers of thickness LL:

ms=ρ (Whj+Lpwf) 2L=0.39 g per pack.m_s = \rho\,(W h_j + L_p w_f)\,2L = 0.39\ \text{g per pack}.

Thermodynamic minimum. The seal is heated, fused and cooled back to ambient: its final state equals its initial state except for the new bond, whose interfacial energy is negligible. In the reversible limit all the heat could be recovered (ideal regeneration), so the thermodynamic minimum is zero, in agreement with the zero thermodynamic minimum the DOE bandwidth study assigns to packaging.

Minimum heating duty without recovery. Without heat recovery, the least heat is that of bringing the seal mass to the sealing temperature TsT_s and melting its crystalline fraction. Heat flows from the jaw to the interface, so when the interface reaches TsT_s every point between jaw and interface is at least at TsT_s; uniform heating to TsT_s is therefore the lowest possible duty:

Qmin=ms[cp(Ts−T0)+wc ΔhfM]=124 J per pack.Q_{min} = m_s\left[c_p (T_s - T_0) + \frac{w_c\,\Delta h_f}{M}\right] = 124\ \text{J per pack}.

Conductive jaws. A jaw held at Tj>TsT_j > T_s heats the film towards TjT_j. The heat absorbed after a dwell tt follows from the mean temperature of the plane wall (Section 3):

Q(t)=ms[cp(Tj−T0) (1−θˉ(Fo))+wc ΔhfM],Q(t) = m_s\left[c_p (T_j - T_0)\,(1 - \bar\theta(Fo)) + \frac{w_c\,\Delta h_f}{M}\right],

141 J at the capability-limited dwell and 147 J at the operating dwell, where the film is practically at jaw temperature. Per kilogram of product (0.5 kg bags) the sealing heat is 0.25–0.29 kJ/kg, two orders of magnitude below the documented energy intensity of a whole packaging step (DOE, frozen vegetables: 14 Btu/lb state of the art, 15 Btu/lb typical, i.e. 33–35 kJ/kg). The rest is machinery: jaw heaters losing heat continuously by convection and radiation, drives, vacuum and compressed air.

3. Rate-limiting step — minimum dwell and maximum cycle rate

Heat conduction problem. The two film layers form a slab of thickness 2L2L whose two faces are suddenly brought to TjT_j when the jaws close; the seal interface is the mid-plane. With ideal contact (no thermal resistance between jaw and film) and constant properties, the temperature obeys the one-dimensional heat equation ∂T/∂t=α ∂2T/∂x2\partial T/\partial t = \alpha\,\partial^2 T/\partial x^2, with the thermal diffusivity

α=kρ cp=0.19 mm2/s,\alpha = \frac{k}{\rho\,c_p} = 0.19\ \text{mm}^2/\text{s},

where kk is the thermal conductivity of the film. No open source with a quotable conductivity of polyethylene film was found, so kk is a declared scenario value (0.33 W/(m K), range 0.25–0.45). The classical separation-of-variables solution for the plane wall of half-thickness LL gives the dimensionless mid-plane temperature

θc(Fo)=Tc−TjT0−Tj=∑n=0∞4(−1)n(2n+1)π exp⁡ ⁣[−((2n+1)π2)2Fo],Fo=αtL2,\theta_c(Fo) = \frac{T_c - T_j}{T_0 - T_j} = \sum_{n=0}^{\infty} \frac{4(-1)^n}{(2n+1)\pi}\, \exp\!\left[-\left(\frac{(2n+1)\pi}{2}\right)^2 Fo\right], \qquad Fo = \frac{\alpha t}{L^2},

and the dimensionless mean temperature

θˉ(Fo)=∑n=0∞8(2n+1)2π2exp⁡ ⁣[−((2n+1)π2)2Fo].\bar\theta(Fo) = \sum_{n=0}^{\infty} \frac{8}{(2n+1)^2\pi^2} \exp\!\left[-\left(\frac{(2n+1)\pi}{2}\right)^2 Fo\right].

FoFo, the Fourier number, compares the dwell with the time heat needs to diffuse across one film layer. For Fo>0.2Fo > 0.2 the first term alone is accurate to better than 0.2%.

Minimum dwell. The seal is sound when the interface reaches TsT_s, i.e. when θc=θs=(Tj−Ts)/(Tj−T0)\theta_c = \theta_s = (T_j - T_s)/(T_j - T_0). Solving θc(Fomin)=θs\theta_c(Fo_{min}) = \theta_s (bisection on the series):

tmin=Fomin L2α.t_{min} = \frac{Fo_{min}\,L^2}{\alpha} .

With Tj=Ts+30T_j = T_s + 30 K = 150 °C, T0T_0 = 25 °C and LL = 50 µm, θs\theta_s = 0.24, FominFo_{min} = 0.676 and tmint_{min} = 9.1 ms. The dwell scales with L2L^2 and with 1/k1/k: doubling the film thickness quadruples it. The latent heat of melting is left out of the conduction problem; it slows the advance of the melt front, so tmint_{min} is a lower bound.

Capability-limited dwell. The jaw temperature fluctuates with standard deviation σTj\sigma_{T_j} and the film thickness with coefficient of variation cLc_L. A capable process holds the jaws until the interface is z σTjz\,\sigma_{T_j} above TsT_s on the thickest film of the tolerance band, L(1+zcL)L(1 + z c_L):

θc(Focap)=Tj−(Ts+zσTj)Tj−T0,tcap=Focap L2(1+zcL)2α=14.6 ms.\theta_c(Fo_{cap}) = \frac{T_j - (T_s + z\sigma_{T_j})}{T_j - T_0}, \qquad t_{cap} = \frac{Fo_{cap}\,L^2 (1 + z c_L)^2}{\alpha} = 14.6\ \text{ms}.

Indexing motion. Between two seals the film advances one bag length LpL_p and each jaw travels its stroke sjs_j open and closed. The fastest motion over a distance ss with a maximum acceleration aa is bang-bang (accelerate half-way, decelerate half-way), lasting 2s/a2\sqrt{s/a}:

tindex=2Lpaf+2×2sjaj=0.37 s.t_{index} = 2\sqrt{\frac{L_p}{a_f}} + 2 \times 2\sqrt{\frac{s_j}{a_j}} = 0.37\ \text{s}.

Cycle rates.

n˙max=1tmin+tindex=158 min−1,n˙cap=1tcap+tindex=156 min−1,n˙typ=1top+tindex=90 min−1,\dot n_{max} = \frac{1}{t_{min} + t_{index}} = 158\ \text{min}^{-1}, \qquad \dot n_{cap} = \frac{1}{t_{cap} + t_{index}} = 156\ \text{min}^{-1}, \qquad \dot n_{typ} = \frac{1}{t_{op} + t_{index}} = 90\ \text{min}^{-1},

where topt_{op} = 0.30 s is the dwell set in operation (declared scenario). Operating dwells are one to two orders of magnitude above the conduction limit of a bare film because of jaw covers, contact resistance, outer laminate layers, latent heat and the time the molten interface needs for chain interdiffusion; these are explained in the loss cascade.

4. Process capability — quality ceiling

At the capability-limited dwell the interface temperature depends on the jaw temperature and on the film thickness. A first-order propagation of their variability gives

σint2=(∂Tint∂Tj σTj)2+(∂Tint∂L cLL)2=(4.0 K)2,\sigma_{int}^2 = \left(\frac{\partial T_{int}}{\partial T_j}\,\sigma_{T_j}\right)^2 + \left(\frac{\partial T_{int}}{\partial L}\,c_L L\right)^2 = (4.0\ \text{K})^2,

with the derivatives evaluated numerically on the conduction solution. Two defects are counted:

u=Φ ⁣(Ts−Tˉintσint)(under-seal),o=Φ ⁣(Tj−(Ts+ΔTw)σTj)(over-seal),u = \Phi\!\left(\frac{T_s - \bar T_{int}}{\sigma_{int}}\right) \quad\text{(under-seal)}, \qquad o = \Phi\!\left(\frac{T_j - (T_s + \Delta T_w)}{\sigma_{T_j}}\right) \quad\text{(over-seal)},

where Tˉint\bar T_{int} is the nominal interface temperature (139 °C), ΔTw\Delta T_w the width of the sealing window above TsT_s (beyond it the film thins, shrinks or burns through) and Φ\Phi the standard normal distribution function. Then

Qmax=1−u−o.Q_{max} = 1 - u - o .

With a 3σ margin the under-seal share is about 10−610^{-6}; the quality ceiling falls when the jaw set point approaches the upper limit of the window.

5. Unavoidable stops — maximum availability

A reel lasts Lr/vL_r/v = 51 min at the capability-limited web speed v=Lp n˙capv = L_p\,\dot n_{cap} = 39 m/min. Each manual reel change stops the machine for tspt_{sp}, but an automatic zero-speed splicer removes the stop (not the splice waste), and each campaign ends with a changeover of duration tcot_{co}, a decision of the product mix. Neither stop is forced by physics or regulation, and no cleaning-in-place applies to the machine (the cleaning model is not used), so

Amax=1.A_{max} = 1 .

With the declared manual splices and changeovers,

Ascen=tcamptcamp+nrtsp+tco=0.909,A_{scen} = \frac{t_{camp}}{t_{camp} + n_r t_{sp} + t_{co}} = 0.909 ,

which enters only oee_scenario.

6. Physics-bounded OEE

Scope of the bound. The theoretical label of OEEmaxOEE_{max} means physics-bounded under the declared scenario: the ceiling follows from the physics of the operation for the declared product, equipment and schedule, and it is a bound only conditional on those declarations. It follows the common definition of all models: AmaxA_{max} counts only stops required by regulation or forced by a physical mechanism, at their physical minimum duration, plus the start-up they force; PmaxP_{max} is the ratio of the physics-limited ideal cycle to the cycle of the capable process; QmaxQ_{max} is the share of conforming units, and mass losses of conforming product are reported only as yield.

OEEmax=Amax×Pmax×Qmax,Pmax=tmin+tindextcap+tindex=0.986.OEE_{max} = A_{max} \times P_{max} \times Q_{max}, \qquad P_{max} = \frac{t_{min} + t_{index}}{t_{cap} + t_{index}} = 0.986 .

The performance ceiling compares the capability-limited cycle with the pure conduction limit: it is the price of making every seal sound. The result is OEEmaxOEE_{max} = 0.986, set by the seal capability margin; with the declared manual splices and changeovers, oee_scenario = 0.896. The capability-limited dwell and rate use declared tolerances, so they are reported without the best-available-technique label.

7. Assumptions and validity

See the assumption and validity lists generated from the configuration file. The most influential inputs (sensitivity table) are the splice and changeover durations, the reel length and the campaign length for OEE; the film thickness, conductivity and jaw-to-seal temperature difference for the dwell.

References

  • Gaur, U., Wunderlich, B. (1981). Heat capacity and other thermodynamic properties of linear macromolecules. II. Polyethylene. Journal of Physical and Chemical Reference Data, 10, 119–152. doi:10.1063/1.555636
  • U.S. Department of Energy. Bandwidth Study on Energy Use and Potential Energy Saving Opportunities in U.S. Food and Beverage Manufacturing, 2017.

7Parameters and provenance

Every input with its value, unit, role, uncertainty distribution and provenance. Open a quote to read the passage of the source that states the value.
  • wcw_c0.45

    Mass-fraction crystallinity of the polyethylene sealant film

    Scenario · Uniform 0.35 to 0.55

    Declared assumption

    Range of low-density polyethylene films; declared assumption.

  • ρc\rho_c1.003 Mg/m³

    Density of crystalline polyethylene at 298 K

    Property · Fixed

    Verified quote
    Show verbatim quote
    recalculated using eq (2) and p,. = 1.0030 Mg mHeat capacity and other thermodynamic properties of linear macromolecules. II. Polyethylene (Gaur, U.; Wunderlich, B.), Journal of Physical and Chemical Reference Data 10, 119 (1981) (opens in a new tab). American Institute of Physics for the National Institute of Standards and Technology (NIST reprint), 1981. p. 5. doi:10.1063/1.555636
  • ρa\rho_a0.8519 Mg/m³

    Density of amorphous polyethylene at 298 K

    Property · Fixed

    Verified quote
    Show verbatim quote
    The amorphous density has been well established at 0.8519Heat capacity and other thermodynamic properties of linear macromolecules. II. Polyethylene (Gaur, U.; Wunderlich, B.), Journal of Physical and Chemical Reference Data 10, 119 (1981) (opens in a new tab). American Institute of Physics for the National Institute of Standards and Technology (NIST reprint), 1981. p. 4. doi:10.1063/1.555636
  • Cp,cC_{p,c}22.38 J/mol/K

    Heat capacity of crystalline polyethylene at 310 K, per mole of CH2 repeat unit (recommended data)

    Property · Fixed

    Verified quote
    Show verbatim quote
    310.0 22.38 3796Heat capacity and other thermodynamic properties of linear macromolecules. II. Polyethylene (Gaur, U.; Wunderlich, B.), Journal of Physical and Chemical Reference Data 10, 119 (1981) (opens in a new tab). American Institute of Physics for the National Institute of Standards and Technology (NIST reprint), 1981. p. 30. doi:10.1063/1.555636
  • Cp,aC_{p,a}31.33 J/mol/K

    Heat capacity of amorphous polyethylene at 310 K, per mole of CH2 repeat unit (recommended data)

    Property · Fixed

    Verified quote
    Show verbatim quote
    310.0 31.33 4849.Heat capacity and other thermodynamic properties of linear macromolecules. II. Polyethylene (Gaur, U.; Wunderlich, B.), Journal of Physical and Chemical Reference Data 10, 119 (1981) (opens in a new tab). American Institute of Physics for the National Institute of Standards and Technology (NIST reprint), 1981. p. 26. doi:10.1063/1.555636
  • Δhf\Delta h_f4.051 kJ/mol

    Heat of fusion of fully crystalline polyethylene at 380 K, per mole of CH2

    Property · Fixed

    Verified quote
    Show verbatim quote
    380 4.051 390 4.084Heat capacity and other thermodynamic properties of linear macromolecules. II. Polyethylene (Gaur, U.; Wunderlich, B.), Journal of Physical and Chemical Reference Data 10, 119 (1981) (opens in a new tab). American Institute of Physics for the National Institute of Standards and Technology (NIST reprint), 1981. p. 32. doi:10.1063/1.555636
  • MM14.027 g/mol

    Molar mass of the CH2 repeat unit

    Property · Fixed

    Computed

    12.011 + 2 x 1.008 g/mol (standard atomic weights).

  • kk0.33 W/m/K

    Thermal conductivity of the polyethylene film

    Scenario · Uniform 0.25 to 0.45 W/m/K

    Declared assumption

    No open source with a quotable conductivity of polyethylene film was found; declared assumption with a wide range. It enters the dwell time inversely.

  • LL50 micrometer

    Thickness of one film layer (distance from the jaw face to the seal interface)

    Scenario · Uniform 35 to 70 micrometer

    Declared assumption
  • cLc_L0.05

    Coefficient of variation of the film thickness

    Scenario · Uniform 0.03 to 0.08

    Declared assumption
  • T0T_025 °C

    Initial film temperature

    Scenario · Uniform 15 to 30 °C

    Declared assumption
  • TsT_s120 °C

    Interface temperature required for a sound seal (seal initiation temperature of the sealant)

    Scenario · Uniform 110 to 130 °C

    Declared assumption

    Must lie above the melting range of the crystallites and below the equilibrium melting temperature of polyethylene (414.6 K); no open source with a quotable seal initiation temperature was used.

  • ΔTj\Delta T_j30 K

    Jaw set-point above the sealing temperature

    Scenario · Uniform 20 to 40 K

    Declared assumption
  • σTj\sigma_{T_j}3 K

    Standard deviation of the jaw face temperature under control

    Scenario · Uniform 1.5 to 4 K

    Declared assumption
  • zz3

    Capability margin in standard deviations used to set the capable dwell

    Scenario · Uniform 2.5 to 3.5

    Declared assumption

    Operating choice, point value at the centre of the declared range 2.5-3.5; a larger margin lengthens the dwell and lowers the under-seal share.

  • ΔTw\Delta T_w60 K

    Width of the sealing window above the sealing temperature (beyond it the film thins

    Scenario · Uniform 50 to 70 K

    Declared assumption
  • topt_{op}0.3 s

    Jaw dwell time set in operation (jaw covers, contact resistance and laminate layers lengthen it)

    Scenario · Uniform 0.15 to 0.6 s

    Declared assumption

    No open source with documented dwell times was used; declared assumption.

  • LpL_p0.25 m

    Film length per bag (index length)

    Scenario · Fixed

    Declared assumption
  • WW0.15 m

    Flat width of the bag (length of the cross seal)

    Scenario · Fixed

    Declared assumption
  • hjh_j0.012 m

    Height of the cross-seal jaws (top seal of one bag plus bottom seal of the next)

    Scenario · Fixed

    Declared assumption
  • wfw_f0.01 m

    Width of the longitudinal fin seal

    Scenario · Fixed

    Declared assumption
  • mpm_p0.5 kg

    Mass of product per bag

    Scenario · Fixed

    Declared assumption
  • afa_f20 m/s²

    Maximum acceleration of the film transport (limited by film tension and slip of the pull belts)

    Scenario · Uniform 10 to 40 m/s²

    Declared assumption
  • sjs_j0.04 m

    Opening stroke of each jaw

    Scenario · Fixed

    Declared assumption
  • aja_j30 m/s²

    Maximum acceleration of the jaw carriage

    Scenario · Uniform 15 to 50 m/s²

    Declared assumption
  • LrL_r2,000 m

    Film length on one reel

    Scenario · Uniform 1,000 to 4,000 m

    Declared assumption
  • LwL_w3 m

    Film wasted at each reel splice

    Scenario · Uniform 1 to 6 m

    Declared assumption
  • tspt_{sp}3 min

    Machine stop per manual reel change and splice (zero with an automatic zero-speed splicer)

    Scenario · Uniform 1 to 6 min

    Declared assumption
  • tcampt_{camp}8 h

    Production time between two format or product changeovers

    Scenario · Uniform 4 to 24 h

    Declared assumption
  • tcot_{co}20 min

    Duration of a changeover

    Scenario · Uniform 10 to 45 min

    Declared assumption
  • nsun_{su}20

    Bags wasted while the machine stabilises after a changeover

    Scenario · Uniform 5 to 50

    Declared assumption

8Benchmarks

Documented values from open sources used to check the ceilings; no documented value may beat the theoretical limit.
BenchmarkCeilingValueProvenance
DOE bandwidth study, thermodynamic minimum energy intensity of packaging of frozen vegetables
Show verbatim quote
Freezing -53.5 to 586 279 279 -48.6 12.1 5.8 5.8 -1.02 Packaging 15 14 14 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 56. DOE/EE-1571; OSTI ID 1512366
Theoretical0 Btu/lbVerified quote
DOE bandwidth study, state-of-the-art on-site energy intensity of packaging of frozen vegetables, per lb of product (whole packaging step; the theoretical output of this model is per pack, compare with heat_min_seal_per_kg)
Show verbatim quote
Freezing -53.5 to 586 279 279 -48.6 12.1 5.8 5.8 -1.02 Packaging 15 14 14 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 56. DOE/EE-1571; OSTI ID 1512366
Best available technique14 Btu/lbVerified quote
DOE bandwidth study, current typical on-site energy intensity of packaging of frozen vegetables, per lb of product (whole packaging step; the theoretical output of this model is per pack, compare with heat_typical_per_kg)
Show verbatim quote
Freezing -53.5 to 586 279 279 -48.6 12.1 5.8 5.8 -1.02 Packaging 15 14 14 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 56. DOE/EE-1571; OSTI ID 1512366
Typical15 Btu/lbVerified quote

9Unavoidable stops

Stops that physics or regulation impose; they set the maximum availability.
  • Reel change and splice (scenario stop with a manual splicer: availability_scenario only)Declared assumption

    A reel holds a finite film length; at the web speed of the machine it runs out after L_r / v. A manual splice stops the machine for t_sp; an automatic zero-speed splicer removes the stop but not the splice waste.

  • Format or product changeover (scenario stop: availability_scenario only)Declared assumption

    Change of bag size, film or product requires stopping, adjusting forming set and jaws, and restarting with start-up waste. Declared scenario values.

10Assumptions

  1. No stop is forced by physics or regulation: an automatic zero-speed splicer removes the reel-change stop (the splice waste remains in the film yield) and changeovers follow the product mix, so availability_max = 1 and both stops enter only availability_scenario and oee_scenario. No cleaning-in-place applies to a form-fill-seal machine, so the cleaning model is not used. Dwell and rate with the capability margin use declared tolerances and are reported without the bat label.
  2. One-dimensional transient conduction through two identical film layers between two jaws at the same constant temperature (symmetric plane wall with fixed surface temperature, ideal contact).
  3. Constant properties evaluated near room temperature; the latent heat of fusion is not included in the conduction problem, which makes the computed dwell a lower bound, and it is included in the energy balance.
  4. A seal is sound when the interface reaches the sealing temperature during the dwell; under-seals and over-seals are the only quality losses (contamination of the seal area by product is not modelled).
  5. Film and jaw carriage move with bang-bang (triangular velocity) profiles at their maximum acceleration; the longitudinal seal does not limit the rate.
  6. Film yield counts splice and start-up waste only; trim does not exist in a fin-sealed pillow bag.

11Range of validity

  • Polyolefin sealant films sealed with constant-temperature (hot) jaws on both sides; impulse and ultrasonic sealing are outside the model.
  • Sealing temperatures below the equilibrium melting temperature of polyethylene (414.6 K) and film thicknesses of 20 to 100 micrometres per layer.

12Sensitivity

Elasticity: relative change of the output for a relative change of each parameter. Spearman rank correlation from the Monte Carlo draws is shown alongside.
  • LLThickness of one film layer (distance from the jaw face to the seal interface)
    elasticity -0.028Spearman ρ -0.72
  • zzCapability margin in standard deviations used to set the capable dwell
    elasticity -0.018Spearman ρ -0.21
  • MMMolar mass of the CH2 repeat unit
    elasticity +0.014Spearman ρ —
  • kkThermal conductivity of the polyethylene film
    elasticity +0.014Spearman ρ +0.29
  • ΔTj\Delta T_jJaw set-point above the sealing temperature
    elasticity +0.011Spearman ρ +0.28
  • cLc_LCoefficient of variation of the film thickness
    elasticity -0.010Spearman ρ -0.36
  • Cp,aC_{p,a}Heat capacity of amorphous polyethylene at 310 K, per mole of CH2 repeat unit (recommended data)
    elasticity -0.009Spearman ρ —
  • ρa\rho_aDensity of amorphous polyethylene at 298 K
    elasticity -0.008Spearman ρ —
  • σTj\sigma_{T_j}Standard deviation of the jaw face temperature under control
    elasticity -0.008Spearman ρ -0.24
  • ρc\rho_cDensity of crystalline polyethylene at 298 K
    elasticity -0.006Spearman ρ —
  • Cp,cC_{p,c}Heat capacity of crystalline polyethylene at 310 K, per mole of CH2 repeat unit (recommended data)
    elasticity -0.005Spearman ρ —
  • LpL_pFilm length per bag (index length)
    elasticity +0.004Spearman ρ —
  • afa_fMaximum acceleration of the film transport (limited by film tension and slip of the pull belts)
    elasticity -0.004Spearman ρ -0.19
  • TsT_sInterface temperature required for a sound seal (seal initiation temperature of the sealant)
    elasticity -0.004Spearman ρ -0.03
  • aja_jMaximum acceleration of the jaw carriage
    elasticity -0.003Spearman ρ -0.13
  • sjs_jOpening stroke of each jaw
    elasticity +0.003Spearman ρ —
  • wcw_cMass-fraction crystallinity of the polyethylene sealant film
    elasticity +0.001Spearman ρ +0.01
  • T0T_0Initial film temperature
    elasticity +0.001Spearman ρ +0.02
  • Output rises with the parameter
  • Output falls with the parameter

13Validation checks

A model is published only when every check passes.
  • Dimensional analysis31 outputs converted to their declared unitsPassed
  • Every cited value verified against its source8 verified, 0 failedPassed
  • No documented value beats the theoretical limitPassed
  • Ceilings in physical orderPassed
  • Fractions within 0 and 1Passed

14Causes of loss in this operation

Probability that each cause is documented as a relevant loss of a line, pooled over all segments.

15References

  1. Heat capacity and other thermodynamic properties of linear macromolecules. II. Polyethylene (Gaur, U.; Wunderlich, B.), Journal of Physical and Chemical Reference Data 10, 119 (1981) (opens in a new tab). American Institute of Physics for the National Institute of Standards and Technology (NIST reprint), 1981. p. 5. doi:10.1063/1.555636
  2. Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (opens in a new tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. p. 56. DOE/EE-1571; OSTI ID 1512366
  3. doi:10.1063/1.555636 — Heat capacity, heat of fusion and densities of polyethylene.