foratvise
Get Started
Equipment failure (breakdowns)

Filler timing worm/synchronization fault

Equipment failure (breakdowns)AvailabilityFilling

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 120 studies that could observe it (sparse evidence).

What happens

The worm gear (timing screw) that indexes containers under the filling valves loses correct phase relative to the valve/turret drive because of mechanical wear, backlash, loose fasteners or an incorrectly set cam/gear train. The resulting mis-timing causes valves to open or close out of register with the container position, producing mechanical interference, spillage or jamming that stops the machine until the drive is realigned.

What is done about it

Perform periodic inspection and readjustment of the worm gear and valve-drive timing, tightening fasteners and resetting cam/gear phase to specification, and replace worn gear, bushing or bearing components proactively. Include timing-chain or gear-train alignment checks in the preventive-maintenance plan and verify synchronization with the container-indexing reference after any adjustment.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.6%]
Expected share of lost time
0.3% [0.1–0.9%]
Share of lost time when present
57% [46–68%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.3%]18 studies
  • Soft drinks, bottled water and juices
    0.5% [0.1–1.6%]44 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.2%]16 studies
  • Bakery and pasta
    0.7% [0.1–2.7%]0 studies
  • Meat, poultry and seafood
    0.7% [0.1–2.4%]6 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.6%]4 studies
  • Grain and oilseed milling
    1.0% [0.1–3.6%]6 studies
  • Sugar and confectionery
    0.7% [0.1–2.5%]3 studies
  • Snacks, coffee, tea and other foods
    0.7% [0.1–2.5%]6 studies
  • Animal feed and pet food
    0.7% [0.1–2.6%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.4%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The worm gear (timing screw) that indexes containers under the filling valves loses correct phase relative to the valve/turret drive because of mechanical wear, backlash, loose fasteners or an incorrectly set cam/gear train. The resulting mis-timing causes valves to open or close out of register with the container position, producing mechanical interference, spillage or jamming that stops the machine until the drive is realigned.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows discrete equipment-failure stops on the filler logged with mechanical/timing fault codes, often preceded by recurring short stops or jam alarms on the same station as wear progresses. Encoder or position-sensor data for the worm/valve drive shows phase drift or out-of-tolerance deviation relative to the container-indexing reference just before the stop.

Countermeasure

Engineering guidance

Perform periodic inspection and readjustment of the worm gear and valve-drive timing, tightening fasteners and resetting cam/gear phase to specification, and replace worn gear, bushing or bearing components proactively. Include timing-chain or gear-train alignment checks in the preventive-maintenance plan and verify synchronization with the container-indexing reference after any adjustment.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 50.7 % · as reported: “synching and worm adjustment issues”
    Show verbatim quote
    The filling machine caused 50.7% of downtime, primarily due to synching and worm adjustment issues.