foratvise
Get Started
Setup and adjustments

Film and film-holding equipment changeover

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 56 % of the line's lost time. Reported by 1 of the 112 studies that could observe it (sparse evidence).

What happens

To switch to a different film size or specification, the operator must stop the packaging machine, remove the current film reel and its holding/mounting fixtures, fit the new reel and adjust the holders, guides and sealing elements to the new dimensions, then verify tracking and seal quality before resuming production. This mechanical reconfiguration consumes non-productive time between the last good pack of the previous run and the first good pack of the new run.

What is done about it

Apply quick-changeover (SMED) principles: pre-stage the new film reel and holding fixtures near the line, use standardized or tool-less quick-release holders, and pre-set guide and sealing adjustments offline on a secondary fixture so only final fine-tuning is done on the running machine. Sequencing production to group runs by similar film size further reduces the frequency and duration of these changeovers.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.4%]
Expected share of lost time
0.3% [0.1–0.8%]
Share of lost time when present
56% [44–67%]
Studies / units
112 / 155
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–1.9%]14 studies
  • Soft drinks, bottled water and juices
    0.7% [0.1–2.3%]33 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.1%]14 studies
  • Bakery and pasta
    0.6% [0.1–2.1%]6 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.4%]6 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.3%]4 studies
  • Grain and oilseed milling
    0.6% [0.1–2.3%]4 studies
  • Sugar and confectionery
    0.6% [0.1–2.2%]4 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.2%]8 studies
  • Animal feed and pet food
    0.6% [0.1–2.2%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.0%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

To switch to a different film size or specification, the operator must stop the packaging machine, remove the current film reel and its holding/mounting fixtures, fit the new reel and adjust the holders, guides and sealing elements to the new dimensions, then verify tracking and seal quality before resuming production. This mechanical reconfiguration consumes non-productive time between the last good pack of the previous run and the first good pack of the new run.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows an extended machine-stopped or changeover state between two production orders with no fault alarm active, often tagged manually by the operator as a format or size change. Downstream conveyors show starvation while upstream units may continue running, and the event log records a changeover reason code aligned with a product or film-size code change.

Countermeasure

Engineering guidance

Apply quick-changeover (SMED) principles: pre-stage the new film reel and holding fixtures near the line, use standardized or tool-less quick-release holders, and pre-set guide and sealing adjustments offline on a secondary fixture so only final fine-tuning is done on the running machine. Sequencing production to group runs by similar film size further reduces the frequency and duration of these changeovers.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 5.00 min · as reported: “Changing the film guide bar to a double bar”
    Show verbatim quote
    เปลี่ยนราว (Bar) พาฟิล์ม เป็นราวคู่ 1 5
  2. Lost time: 10.0 min · as reported: “Changing film size and film-holding equipment”
    Show verbatim quote
    เปลี่ยนขนาดฟิล์ม และอุปกรณ์ช่วยยึดฟิล์ม 1 10