foratvise
Get Started
Idling and minor stops (micro-stops)

Gauge roller jam or material buildup

Idling and minor stops (micro-stops)PerformanceForming, moulding and depositing

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 53 % of the line's lost time. Reported by 0 of the 76 studies that could observe it (sparse evidence).

What happens

The gauge roller, which sets the thickness of the dough or sheet by compressing it between rolls, accumulates sticky product residue or encounters an oversized lump of material that jams the nip or throws off the roller gap. The resulting obstruction stalls the sheet feed and triggers an automatic stop or requires the operator to clear the roller before production can resume.

What is done about it

Implement scheduled cleaning or scraping of the gauge roller surface to prevent sticky buildup, and install upstream screening or lump detection to remove oversized material before it reaches the rollers. Adjusting roller gap tolerances and using non-stick coatings or surface treatments also reduces jam frequency.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.3%]
Expected share of lost time
0.2% [0.0–0.7%]
Share of lost time when present
53% [41–64%]
Studies / units
76 / 96
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.5% [0.0–2.1%]5 studies
  • Soft drinks, bottled water and juices
    0.5% [0.0–1.9%]11 studies
  • Brewing, wine and spirits
    0.5% [0.0–2.3%]0 studies
  • Bakery and pasta
    0.4% [0.0–1.7%]25 studies
  • Meat, poultry and seafood
    0.5% [0.0–2.1%]3 studies
  • Fruit and vegetable processing
    0.5% [0.0–2.1%]3 studies
  • Grain and oilseed milling
    0.5% [0.0–2.1%]0 studies
  • Sugar and confectionery
    0.5% [0.0–2.0%]8 studies
  • Snacks, coffee, tea and other foods
    0.5% [0.0–2.0%]7 studies
  • Animal feed and pet food
    0.5% [0.0–2.0%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.5% [0.0–1.9%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The gauge roller, which sets the thickness of the dough or sheet by compressing it between rolls, accumulates sticky product residue or encounters an oversized lump of material that jams the nip or throws off the roller gap. The resulting obstruction stalls the sheet feed and triggers an automatic stop or requires the operator to clear the roller before production can resume.

How it looks in SCADA data

Engineering guidance

Short-duration stop events logged at the forming/sheeting station, often with the roller drive showing a torque or current spike just before the stop, followed by a brief idle state cleared manually by the operator without a maintenance work order. Downstream equipment may show starvation during the stop.

Countermeasure

Engineering guidance

Implement scheduled cleaning or scraping of the gauge roller surface to prevent sticky buildup, and install upstream screening or lump detection to remove oversized material before it reaches the rollers. Adjusting roller gap tolerances and using non-stick coatings or surface treatments also reduces jam frequency.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 3.00 min · as reported: “Gauge Roller”
    Show verbatim quote
    Gauge Roller 1 2 3