foratvise
Get Started
Process defects (scrap and rework)

Impurity/dirt carryover from first-press separation

Process defects (scrap and rework)QualitySeparation (centrifugation, filtration, membranes)

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 1 of the 37 studies that could observe it (sparse evidence).

What happens

During the first mechanical pressing/separation stage, fine solids, fibers, sludge and other foreign matter are not fully separated from the extracted liquid (e.g. oil) and remain entrained in the output stream. This happens when screen openings, press clearances or clarification conditions let particulate contamination pass through instead of being rejected with the cake or sludge fraction.

What is done about it

Inspect and maintain press screens, cones and clearances to ensure proper solid-liquid separation, and adjust press settings (pressure, throughput, screen mesh) to match feed characteristics. Reinforce downstream clarification or filtration steps and schedule regular cleaning to prevent buildup that bypasses solids into the clarified stream.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.0% [0.2–3.0%]
Expected share of lost time
0.5% [0.1–1.4%]
Share of lost time when present
48% [35–60%]
Studies / units
37 / 44
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.1% [0.1–4.7%]5 studies
  • Soft drinks, bottled water and juices
    1.1% [0.1–4.7%]1 study
  • Brewing, wine and spirits
    1.1% [0.1–4.5%]1 study
  • Bakery and pasta
    1.2% [0.1–4.8%]0 studies
  • Meat, poultry and seafood
    1.1% [0.1–4.4%]2 studies
  • Fruit and vegetable processing
    1.1% [0.1–4.6%]3 studies
  • Grain and oilseed milling
    1.6% [0.2–6.4%]6 studies
  • Sugar and confectionery
    1.1% [0.1–4.4%]3 studies
  • Snacks, coffee, tea and other foods
    1.1% [0.1–4.5%]4 studies
  • Animal feed and pet food
    1.1% [0.1–4.3%]5 studies
  • Food manufacturing (unspecified or mixed)
    1.1% [0.1–4.2%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During the first mechanical pressing/separation stage, fine solids, fibers, sludge and other foreign matter are not fully separated from the extracted liquid (e.g. oil) and remain entrained in the output stream. This happens when screen openings, press clearances or clarification conditions let particulate contamination pass through instead of being rejected with the cake or sludge fraction.

How it looks in SCADA data

Engineering guidance

Quality or lab systems log out-of-spec dirt/impurity content readings on batches from the first press, often with repeated downgrade or rework flags on the same equipment; process parameters show normal run states with no stoppage, so the loss appears purely as a quality deviation rather than a downtime event.

Countermeasure

Engineering guidance

Inspect and maintain press screens, cones and clearances to ensure proper solid-liquid separation, and adjust press settings (pressure, throughput, screen mesh) to match feed characteristics. Reinforce downstream clarification or filtration steps and schedule regular cleaning to prevent buildup that bypasses solids into the clarified stream.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Defect rate: 10.8 % · as reported: “dirty (kotoran)”
    Show verbatim quote
    1 Agustus 286.221 10,76 30.797 89,24
  2. Defect rate: 10.6 % · as reported: “dirty (kotoran)”
    Show verbatim quote
    2 September 273.539 10,58 28.940 89,42
  3. Defect rate: 11.4 % · as reported: “dirty (kotoran)”
    Show verbatim quote
    3 Oktober 434.209 11,39 49.456 88,61
  4. Defect rate: 9.89 % · as reported: “dirty (kotoran)”
    Show verbatim quote
    4 November 391.254 9,89 38.695 90,11
  5. Defect rate: 9.83 % · as reported: “dirty (kotoran)”
    Show verbatim quote
    5 Desember 478.645 9,83 47.051 90,17