foratvise
Get Started
Reduced speed

Laser Marking Machine Speed Loss

Reduced speedPerformanceLabeling and coding

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 63 % of the line's lost time. Reported by 1 of the 85 studies that could observe it (sparse evidence).

What happens

The laser marking machine runs below its rated throughput because the beam power, optics focus or marking parameters have drifted, forcing the control system or the operator to slow the marking pass to keep the code legible and durable on the substrate. Substrate variability (surface finish, curvature, material batch) can also require a lower effective speed to avoid incomplete or unreadable codes.

What is done about it

Apply a preventive maintenance routine on the laser source and optics, including cleaning, alignment checks and power verification, and standardize marking parameters by substrate and product type. Introduce real-time mark-quality feedback so that speed is only reduced when strictly necessary and restored automatically once conditions normalize.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.8% [0.2–2.3%]
Expected share of lost time
0.5% [0.1–1.5%]
Share of lost time when present
63% [49–75%]
Studies / units
85 / 113
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.9% [0.1–3.3%]11 studies
  • Soft drinks, bottled water and juices
    0.8% [0.1–2.6%]29 studies
  • Brewing, wine and spirits
    0.9% [0.1–3.1%]13 studies
  • Bakery and pasta
    1.5% [0.1–5.9%]1 study
  • Meat, poultry and seafood
    1.0% [0.1–3.7%]4 studies
  • Fruit and vegetable processing
    1.0% [0.1–3.7%]4 studies
  • Grain and oilseed milling
    1.0% [0.1–3.5%]3 studies
  • Sugar and confectionery
    1.0% [0.1–3.7%]3 studies
  • Snacks, coffee, tea and other foods
    0.9% [0.1–3.5%]4 studies
  • Animal feed and pet food
    1.0% [0.1–3.7%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.9% [0.1–3.4%]9 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The laser marking machine runs below its rated throughput because the beam power, optics focus or marking parameters have drifted, forcing the control system or the operator to slow the marking pass to keep the code legible and durable on the substrate. Substrate variability (surface finish, curvature, material batch) can also require a lower effective speed to avoid incomplete or unreadable codes.

How it looks in SCADA data

Engineering guidance

MES/SCADA shows the marker in a running state but with actual cycle time or throughput persistently above the nominal value, depressing the OEE performance factor without any associated fault or stop alarm. Logs may show repeated manual speed overrides, reduced line speed setpoints, or laser power/focus parameters outside their normal operating band.

Countermeasure

Engineering guidance

Apply a preventive maintenance routine on the laser source and optics, including cleaning, alignment checks and power verification, and standardize marking parameters by substrate and product type. Introduce real-time mark-quality feedback so that speed is only reduced when strictly necessary and restored automatically once conditions normalize.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 38.0 % · as reported: “performance losses”
    Show verbatim quote
    The analysis of the six significant losses reveals that performance losses are the dominant contributor to overall equipment inefficiency, accounting for 38% of the total OEE loss.