foratvise
Get Started
Equipment failure (breakdowns)

Mold Safety Cam/Closure Mechanism Fault

Equipment failure (breakdowns)AvailabilityForming, moulding and depositing

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 76 studies that could observe it (sparse evidence).

What happens

In blow molding machines, the mold halves are closed and held shut by a cam-driven safety interlock that must fully engage before the blowing cycle can proceed. Wear, misalignment or contamination of the cam, linkage or locking pins prevents proper closure or triggers the safety interlock, stopping the machine or forcing manual readjustment, and the same mechanism often needs recalibration whenever mold tooling is changed over.

What is done about it

Implement preventive maintenance covering inspection, cleaning and lubrication of the cam profile, linkage and interlock sensors, with scheduled replacement based on wear condition. Standardize the mold closure verification and calibration step within the changeover procedure so the safety mechanism is checked and adjusted whenever tooling or format is changed.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.7% [0.1–2.1%]
Expected share of lost time
0.4% [0.1–1.2%]
Share of lost time when present
57% [46–68%]
Studies / units
76 / 96
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.9% [0.1–3.2%]5 studies
  • Soft drinks, bottled water and juices
    1.1% [0.1–4.1%]11 studies
  • Brewing, wine and spirits
    0.9% [0.1–3.3%]0 studies
  • Bakery and pasta
    0.7% [0.1–2.5%]25 studies
  • Meat, poultry and seafood
    0.9% [0.1–3.2%]3 studies
  • Fruit and vegetable processing
    0.9% [0.1–3.2%]3 studies
  • Grain and oilseed milling
    0.9% [0.1–3.4%]0 studies
  • Sugar and confectionery
    0.8% [0.1–2.9%]8 studies
  • Snacks, coffee, tea and other foods
    0.8% [0.1–3.1%]7 studies
  • Animal feed and pet food
    0.8% [0.1–3.3%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.8% [0.1–3.2%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

In blow molding machines, the mold halves are closed and held shut by a cam-driven safety interlock that must fully engage before the blowing cycle can proceed. Wear, misalignment or contamination of the cam, linkage or locking pins prevents proper closure or triggers the safety interlock, stopping the machine or forcing manual readjustment, and the same mechanism often needs recalibration whenever mold tooling is changed over.

How it looks in SCADA data

Engineering guidance

SCADA/MES logs show discrete fault or alarm tags referencing mold closure, safety cam or interlock position, recurring short-to-medium machine-state stops at the mold-close step of the cycle, and a cluster of downtime events immediately following changeover or tooling-change timestamps. Cycle-time traces often show the mold-close phase taking longer or timing out before the fault is raised.

Countermeasure

Engineering guidance

Implement preventive maintenance covering inspection, cleaning and lubrication of the cam profile, linkage and interlock sensors, with scheduled replacement based on wear condition. Standardize the mold closure verification and calibration step within the changeover procedure so the safety mechanism is checked and adjusted whenever tooling or format is changed.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 135 menit · as reported: “Mold Safety Cam Closure”
    Show verbatim quote
    Mold Safety Cam Closure 135
  2. Share of lost time: 6.10 % · as reported: “Equipment Failure Losses”
    Show verbatim quote
    Rata - rata 6,10 0,95 11,47 0,00 0,00 0,21
  3. Share of lost time: 0.950 % · as reported: “Set Up & Adjustment Losses”
    Show verbatim quote
    Rata - rata 6,10 0,95 11,47 0,00 0,00 0,21