foratvise
Get Started
Process defects (scrap and rework)

Batch product out of composition specification

Process defects (scrap and rework)QualityWhole line or unspecified equipment

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 0 of the 127 studies that could observe it (sparse evidence).

What happens

Variability in raw materials, dosing, fermentation kinetics or mixing ratios causes a batch in the fermentation or mixing tank to drift outside the accepted composition window (for example excess acidity or an incorrect blend/consistency), so the whole batch fails first-pass quality criteria. Because the defect is generated in a shared vessel, the entire batch volume is affected rather than individual units.

What is done about it

Install or tighten inline monitoring of pH, acidity or composition with automatic alarms and batch hold logic, standardize raw-material incoming checks and dosing recipes, and review fermentation time/temperature or mixing ratio set points through root-cause analysis whenever a deviation occurs.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.0%]
Expected share of lost time
0.2% [0.0–0.5%]
Share of lost time when present
48% [36–60%]
Studies / units
127 / 161
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.5%]13 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.5%]26 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.5%]11 studies
  • Bakery and pasta
    0.4% [0.0–1.4%]24 studies
  • Meat, poultry and seafood
    0.4% [0.0–1.5%]9 studies
  • Fruit and vegetable processing
    0.4% [0.0–1.6%]7 studies
  • Grain and oilseed milling
    0.4% [0.0–1.6%]6 studies
  • Sugar and confectionery
    0.4% [0.0–1.6%]9 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.7%]5 studies
  • Animal feed and pet food
    0.4% [0.0–1.6%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.7%]10 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Variability in raw materials, dosing, fermentation kinetics or mixing ratios causes a batch in the fermentation or mixing tank to drift outside the accepted composition window (for example excess acidity or an incorrect blend/consistency), so the whole batch fails first-pass quality criteria. Because the defect is generated in a shared vessel, the entire batch volume is affected rather than individual units.

How it looks in SCADA data

Engineering guidance

Tank-level pH, titratable acidity or composition sensors trend outside the control band during or at the end of the batch cycle, triggering a quality alarm or an automatic hold/diversion of the tank to rework or disposal. MES batch records show the lot flagged as non-conforming with no corresponding equipment fault or stop code.

Countermeasure

Engineering guidance

Install or tighten inline monitoring of pH, acidity or composition with automatic alarms and batch hold logic, standardize raw-material incoming checks and dosing recipes, and review fermentation time/temperature or mixing ratio set points through root-cause analysis whenever a deviation occurs.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 24.3 Ton · as reported: “Producto Acido”
    Show verbatim quote
    esto mostró un beneficio tangible al reducir los desvíos por producto ácido de 29.3 a 24.3 toneladas, un beneficio del 16.8% dentro del periodo de estudio.
  2. Lost time: 29.3 Ton · as reported: “Producto Acido”
    Show verbatim quote
    esto mostró un beneficio tangible al reducir los desvíos por producto ácido de 29.3 a 24.3 toneladas, un beneficio del 16.8% dentro del periodo de estudio.
  3. Lost time: 32.6 Ton · as reported: “Producto PIP's”
    Show verbatim quote
    esto representó una reducción de 56.1 a 32.6 toneladas durante el primero y tercer trimestre del 2013 respectivamente, un 41.7% de beneficio registrado.
  4. Lost time: 56.1 Ton · as reported: “Producto PIP's”
    Show verbatim quote
    esto representó una reducción de 56.1 a 32.6 toneladas durante el primero y tercer trimestre del 2013 respectivamente, un 41.7% de beneficio registrado.