foratvise
Get Started
Process defects (scrap and rework)

Out-of-spec pellets requiring reprocessing

Process defects (scrap and rework)QualityForming, moulding and depositing

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 1 of the 76 studies that could observe it (sparse evidence).

What happens

Pellets leaving the pelletizing machine or pellet mill fail durability, size, moisture or density specifications because of die wear, inconsistent conditioning temperature, formulation variability or incorrect die/roll clearance, so the off-spec material and fines must be collected and fed back into the process instead of being accepted as first-pass product.

What is done about it

Standardize conditioning temperature and moisture before the die, schedule die and roll replacement based on wear rather than failure, and tighten formulation and particle-size control upstream to keep pellet durability and dimensions within specification.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.7% [0.1–2.1%]
Expected share of lost time
0.3% [0.1–1.0%]
Share of lost time when present
48% [36–60%]
Studies / units
76 / 96
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.8% [0.1–3.3%]5 studies
  • Soft drinks, bottled water and juices
    0.8% [0.1–2.8%]11 studies
  • Brewing, wine and spirits
    0.9% [0.1–3.4%]0 studies
  • Bakery and pasta
    0.7% [0.1–2.4%]25 studies
  • Meat, poultry and seafood
    0.9% [0.1–3.3%]3 studies
  • Fruit and vegetable processing
    0.8% [0.1–3.1%]3 studies
  • Grain and oilseed milling
    0.8% [0.1–3.2%]0 studies
  • Sugar and confectionery
    0.8% [0.1–3.1%]8 studies
  • Snacks, coffee, tea and other foods
    0.8% [0.1–3.0%]7 studies
  • Animal feed and pet food
    1.2% [0.1–4.4%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.8% [0.1–3.2%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Pellets leaving the pelletizing machine or pellet mill fail durability, size, moisture or density specifications because of die wear, inconsistent conditioning temperature, formulation variability or incorrect die/roll clearance, so the off-spec material and fines must be collected and fed back into the process instead of being accepted as first-pass product.

How it looks in SCADA data

Engineering guidance

MES/quality data show elevated fines or reject counts and recurring rework or recycle-loop batch entries tagged to the pelletizing step, while the pelletizer itself keeps running in normal production state without stopping, so the signature appears as a yield or scrap-rate deviation rather than a downtime event. Correlated signals include die temperature or motor load drift and repeated material recirculation flow on the return conveyor.

Countermeasure

Engineering guidance

Standardize conditioning temperature and moisture before the die, schedule die and roll replacement based on wear rather than failure, and tighten formulation and particle-size control upstream to keep pellet durability and dimensions within specification.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 31.4 % · as reported: “high levels of waste reprocessing”
    Show verbatim quote
    mainly caused by mechanical failures due to the lack of preventive maintenance (48.4%), high levels of waste reprocessing (31.4%), and dosing deviations (3.4%)
  2. Number of events: 11.5 events/round · as reported: “waste reprocessing events”
    Show verbatim quote
    Number of waste reprocessing events 11.5 11.4 0.88%