foratvise
Get Started
Setup and adjustments

Pre-batch equipment cleaning cycle

Setup and adjustmentsAvailabilityForming, moulding and depositing

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 56 % of the line's lost time. Reported by 0 of the 76 studies that could observe it (sparse evidence).

What happens

Before processing a new batch, the tamping/forming equipment must be stopped and manually or semi-automatically cleaned to remove residual product, prevent cross-contamination and avoid build-up that would affect compaction quality. This mandatory hygiene step occurs at every batch boundary and is counted as changeover time rather than running time.

What is done about it

Standardize and simplify the cleaning procedure (quick-release tooling, dedicated cleaning aids, checklists) to shorten the task, and evaluate automating or semi-automating the cleaning step so it can be partially overlapped with other changeover activities or run in parallel on duplicate tooling.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.2%]
Expected share of lost time
0.2% [0.0–0.7%]
Share of lost time when present
56% [44–67%]
Studies / units
76 / 96
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.5% [0.0–2.0%]5 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.6%]11 studies
  • Brewing, wine and spirits
    0.5% [0.0–2.2%]0 studies
  • Bakery and pasta
    0.4% [0.0–1.7%]25 studies
  • Meat, poultry and seafood
    0.5% [0.0–2.0%]3 studies
  • Fruit and vegetable processing
    0.5% [0.0–2.0%]3 studies
  • Grain and oilseed milling
    0.5% [0.0–2.0%]0 studies
  • Sugar and confectionery
    0.5% [0.0–1.9%]8 studies
  • Snacks, coffee, tea and other foods
    0.5% [0.0–1.8%]7 studies
  • Animal feed and pet food
    0.5% [0.0–1.8%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.5% [0.0–1.8%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Before processing a new batch, the tamping/forming equipment must be stopped and manually or semi-automatically cleaned to remove residual product, prevent cross-contamination and avoid build-up that would affect compaction quality. This mandatory hygiene step occurs at every batch boundary and is counted as changeover time rather than running time.

How it looks in SCADA data

Engineering guidance

MES/SCADA logs show a recurring machine state such as cleaning, standby or stopped inserted between the end-of-batch and start-of-next-batch events, with a fairly repeatable duration at every batch transition; upstream and downstream equipment show synchronized starvation or blocking during the same window.

Countermeasure

Engineering guidance

Standardize and simplify the cleaning procedure (quick-release tooling, dedicated cleaning aids, checklists) to shorten the task, and evaluate automating or semi-automating the cleaning step so it can be partially overlapped with other changeover activities or run in parallel on duplicate tooling.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of loss events: 14.4 % · as reported: “25-minute cleaning cycle of the tamping machine before each batch”
    Show verbatim quote
    Additionally, the frequent relocation of raw material pallets within the thawing area represents 18% of waste and the requirement for a 25-minute cleaning cycle of the tamping machine before each batch contributes 14.4%.