foratvise
Get Started
Process defects (scrap and rework)

Out-of-specification parts from press forming

Process defects (scrap and rework)QualityForming, moulding and depositing

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 47 % of the line's lost time. Reported by 0 of the 76 studies that could observe it (sparse evidence).

What happens

During stable press operation, variation in applied force, die alignment, material feed thickness or temperature causes formed parts to deviate from dimensional or cosmetic tolerances; the resulting units are either scrapped outright or routed back for rework before they can be accepted as first-pass good product.

What is done about it

Standardize and monitor press setpoints (force, stroke, temperature) with in-process checks or statistical process control, maintain die and tooling alignment through preventive maintenance, and verify incoming material consistency to keep formed parts within tolerance.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.4%]
Expected share of lost time
0.2% [0.0–0.7%]
Share of lost time when present
47% [36–59%]
Studies / units
76 / 96
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.5% [0.0–2.0%]5 studies
  • Soft drinks, bottled water and juices
    0.5% [0.0–2.2%]11 studies
  • Brewing, wine and spirits
    0.6% [0.0–2.2%]0 studies
  • Bakery and pasta
    0.5% [0.0–1.7%]25 studies
  • Meat, poultry and seafood
    0.6% [0.0–2.3%]3 studies
  • Fruit and vegetable processing
    0.5% [0.0–2.2%]3 studies
  • Grain and oilseed milling
    0.5% [0.0–2.1%]0 studies
  • Sugar and confectionery
    0.5% [0.0–2.0%]8 studies
  • Snacks, coffee, tea and other foods
    0.5% [0.0–2.1%]7 studies
  • Animal feed and pet food
    0.5% [0.0–2.1%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.5% [0.0–2.2%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During stable press operation, variation in applied force, die alignment, material feed thickness or temperature causes formed parts to deviate from dimensional or cosmetic tolerances; the resulting units are either scrapped outright or routed back for rework before they can be accepted as first-pass good product.

How it looks in SCADA data

Engineering guidance

MES/quality logs show elevated counts in scrap and rework tally fields for the press station while machine run-state remains in production, with no corresponding downtime or stop alarm; press force, stroke or position signals may show drift or increased variance correlated with the reject events.

Countermeasure

Engineering guidance

Standardize and monitor press setpoints (force, stroke, temperature) with in-process checks or statistical process control, maintain die and tooling alignment through preventive maintenance, and verify incoming material consistency to keep formed parts within tolerance.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 0.790 % · as reported: “Rework losses”
    Show verbatim quote
    Rework losses 2,60 0,79 100
  2. Lost time: 2.60 jam · as reported: “Rework losses”
    Show verbatim quote
    Rework losses 2,60 0,79 100
  3. Share of lost time: 0 % · as reported: “Scrap losses”
    Show verbatim quote
    Scrap losses 0 0 100
  4. Lost time: 0 jam · as reported: “Scrap losses”
    Show verbatim quote
    Scrap losses 0 0 100