foratvise
Get Started
Equipment failure (breakdowns)

Product pusher bushing wear/failure

Equipment failure (breakdowns)AvailabilityForming, moulding and depositing

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 1 of the 76 studies that could observe it (sparse evidence).

What happens

The bushing that guides and supports the reciprocating product pusher arm on the forming machine wears down through repeated friction and mechanical cycling, or fails due to lack of lubrication or misalignment. As clearance increases, the pusher loses precise motion, binds, or jams, interrupting the forming cycle and requiring mechanical intervention to repair or replace the component.

What is done about it

Implement a preventive maintenance schedule with periodic inspection, lubrication and timely replacement of the pusher bushing based on wear condition, and verify shaft alignment during installation to minimize abnormal loading.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.7% [0.1–2.0%]
Expected share of lost time
0.4% [0.1–1.2%]
Share of lost time when present
58% [47–68%]
Studies / units
76 / 96
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.9% [0.1–3.2%]5 studies
  • Soft drinks, bottled water and juices
    0.8% [0.1–2.9%]11 studies
  • Brewing, wine and spirits
    0.9% [0.1–3.4%]0 studies
  • Bakery and pasta
    0.7% [0.1–2.6%]25 studies
  • Meat, poultry and seafood
    0.9% [0.1–3.4%]3 studies
  • Fruit and vegetable processing
    0.9% [0.1–3.4%]3 studies
  • Grain and oilseed milling
    0.9% [0.1–3.6%]0 studies
  • Sugar and confectionery
    0.8% [0.1–3.0%]8 studies
  • Snacks, coffee, tea and other foods
    1.2% [0.1–4.6%]7 studies
  • Animal feed and pet food
    0.9% [0.1–3.3%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.9% [0.1–3.2%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The bushing that guides and supports the reciprocating product pusher arm on the forming machine wears down through repeated friction and mechanical cycling, or fails due to lack of lubrication or misalignment. As clearance increases, the pusher loses precise motion, binds, or jams, interrupting the forming cycle and requiring mechanical intervention to repair or replace the component.

How it looks in SCADA data

Engineering guidance

SCADA/MES data shows an unplanned stop state on the forming machine with a mechanical fault or jam alarm associated with the pusher axis, often preceded by increasing cycle time variability or torque/current fluctuations on the pusher drive before the full stop. Downstream stations may show starvation once the fault halts product flow.

Countermeasure

Engineering guidance

Implement a preventive maintenance schedule with periodic inspection, lubrication and timely replacement of the pusher bushing based on wear condition, and verify shaft alignment during installation to minimize abnormal loading.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 601 menit · as reported: “pendorong produk (bushing)”
    Show verbatim quote
    equipment failure yang mendominasi pada mesin Sapal adalah pendorong produk (bushing) yaitu sebanyak 601 menit atau 10,01 jam.