foratvise
Get Started
Process defects (scrap and rework)

Quality control rejection at inspection stage

Process defects (scrap and rework)QualityInspection and checkweighing

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 0 of the 79 studies that could observe it (sparse evidence).

What happens

Units produced during otherwise stable operation fail to meet specified quality attributes (fill level, weight, seal integrity, appearance, contamination) and are rejected when checked at the quality control or inspection stage. The root cause is typically a drift in an upstream process parameter or material property that is only caught downstream at the inspection point rather than an outright machine stoppage.

What is done about it

Implement statistical process control with tighter in-line monitoring and automatic feedback loops to the upstream process parameter causing the drift, and perform root-cause analysis on recurring reject patterns to correct material, setpoint, or equipment variability before product reaches inspection.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.3%]
Expected share of lost time
0.2% [0.0–0.6%]
Share of lost time when present
48% [36–59%]
Studies / units
79 / 101
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.5% [0.0–2.0%]10 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.6%]26 studies
  • Brewing, wine and spirits
    0.5% [0.0–1.9%]12 studies
  • Bakery and pasta
    0.5% [0.0–2.1%]0 studies
  • Meat, poultry and seafood
    0.5% [0.0–2.1%]4 studies
  • Fruit and vegetable processing
    0.5% [0.0–2.1%]4 studies
  • Grain and oilseed milling
    0.5% [0.0–2.1%]3 studies
  • Sugar and confectionery
    0.5% [0.0–2.1%]3 studies
  • Snacks, coffee, tea and other foods
    0.5% [0.0–2.0%]4 studies
  • Animal feed and pet food
    0.5% [0.0–2.1%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.5% [0.0–2.1%]9 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Units produced during otherwise stable operation fail to meet specified quality attributes (fill level, weight, seal integrity, appearance, contamination) and are rejected when checked at the quality control or inspection stage. The root cause is typically a drift in an upstream process parameter or material property that is only caught downstream at the inspection point rather than an outright machine stoppage.

How it looks in SCADA data

Engineering guidance

MES/SCADA records show rising reject or downgrade counters at the inspection or checkweighing station while upstream machine states remain in normal run mode, with no corresponding fault alarm; quality parameter trends (weight, fill level, vision system scores) show gradual drift or step changes preceding the reject spikes.

Countermeasure

Engineering guidance

Implement statistical process control with tighter in-line monitoring and automatic feedback loops to the upstream process parameter causing the drift, and perform root-cause analysis on recurring reject patterns to correct material, setpoint, or equipment variability before product reaches inspection.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Defect rate: 2.80 % · as reported: “quality control stage losses”
    Show verbatim quote
    Losses at the quality control stage amounted to approximately 2.8 %, which is considered an acceptable level for high-volume continuous production in the food industry